Cone beam CT analysis of Haller cells: prevalence and clinical significance.
Ontology highlight
ABSTRACT:
SUBMITTER: Mathew R
PROVIDER: S-EPMC3828019 | biostudies-other | 2013
REPOSITORIES: biostudies-other
Similar Datasets
Project description:BackgroundHigh-resolution, low-noise detectors with minimal dead-space at chest-wall could improve posterior coverage and microcalcification visibility in the dedicated cone-beam breast CT (CBBCT). However, the smaller field-of-view necessitates laterally-shifted detector geometry to enable optimizing the air-gap for x-ray scatter rejection.ObjectiveTo evaluate laterally-shifted detector geometry for CBBCT with clinical projection datasets that provide for anatomical structures and lesions.MethodsCBBCT projection datasets (n = 17 breasts) acquired with a 40×30 cm detector (1024×768-pixels, 0.388-mm pixels) were truncated along the fan-angle to emulate 20.3×30 cm, 22.2×30 cm and 24.1×30 cm detector formats and correspond to 20, 120, 220 pixels overlap in conjugate views, respectively. Feldkamp-Davis-Kress (FDK) algorithm with 3 different weighting schemes were used for reconstruction. Visual analysis for artifacts and quantitative analysis of root-mean-squared-error (RMSE), absolute difference between truncated and 40×30 cm reconstructions (Diff), and its power spectrum (PSDiff) were performed.ResultsArtifacts were observed for 20.3×30 cm, but not for other formats. The 24.1×30 cm provided the best quantitative results with RMSE and Diff (both in units of μ, cm-1) of 4.39×10-3±1.98×10-3 and 4.95×10-4±1.34×10-4, respectively. The PSDiff (>0.3 cycles/mm) was in the order of 10-14μ2mm3 and was spatial-frequency independent.ConclusionsLaterally-shifted detector CBBCT with at least 220 pixels overlap in conjugate views (24.1×30 cm detector format) provides quantitatively accurate and artifact-free image reconstruction.
| S-EPMC7347391 | biostudies-literature
Project description:PurposeTo provide initial assessment of image quality and dose for a cone-beam computed tomographic (CT) scanner dedicated to extremity imaging.Materials and methodsA prototype cone-beam CT scanner has been developed for imaging the extremities, including the weight-bearing lower extremities. Initial technical assessment included evaluation of radiation dose measured as a function of kilovolt peak and tube output (in milliampere seconds), contrast resolution assessed in terms of the signal difference-to-noise ratio (SDNR), spatial resolution semiquantitatively assessed by using a line-pair module from a phantom, and qualitative evaluation of cadaver images for potential diagnostic value and image artifacts by an expert CT observer (musculoskeletal radiologist).ResultsThe dose for a nominal scan protocol (80 kVp, 108 mAs) was 9 mGy (absolute dose measured at the center of a CT dose index phantom). SDNR was maximized with the 80-kVp scan technique, and contrast resolution was sufficient for visualization of muscle, fat, ligaments and/or tendons, cartilage joint space, and bone. Spatial resolution in the axial plane exceeded 15 line pairs per centimeter. Streaks associated with x-ray scatter (in thicker regions of the patient--eg, the knee), beam hardening (about cortical bone--eg, the femoral shaft), and cone-beam artifacts (at joint space surfaces oriented along the scanning plane--eg, the interphalangeal joints) presented a slight impediment to visualization. Cadaver images (elbow, hand, knee, and foot) demonstrated excellent visibility of bone detail and good soft-tissue visibility suitable to a broad spectrum of musculoskeletal indications.ConclusionA dedicated extremity cone-beam CT scanner capable of imaging upper and lower extremities (including weight-bearing examinations) provides sufficient image quality and favorable dose characteristics to warrant further evaluation for clinical use.
| S-EPMC4263642 | biostudies-literature
Project description:Background & purposeFour dimensional Cone beam CT (CBCT) has many potential benefits for radiotherapy but suffers from poor image quality, long acquisition times, and/or long reconstruction times. In this work we present a fast iterative reconstruction algorithm for 4D reconstruction of fast acquisition cone beam CT, as well as a new method for temporal regularization and compare to state of the art methods for 4D CBCT.Materials & methodsRegularization parameters for the iterative algorithms were found automatically via computer optimization on 60 s acquisitions using the XCAT phantom. Nineteen lung cancer patients were scanned with 60 s arcs using the onboard image on a Varian trilogy linear accelerator. Images were reconstructed using an accelerated ordered subset algorithm. A frequency based temporal regularization algorithm was developed and compared to the McKinnon-Bates algorithm, 4D total variation and prior images compressed sensing (PICCS).ResultsAll reconstructions were completed in 60 s or less. The proposed method provided a structural similarity of 0.915, compared with 0.786 for the classic McKinnon-bates method. For the patient study, it provided fewer image artefacts than PICCS, and better spatial resolution than 4D TV.ConclusionFour dimensional iterative CBCT reconstruction was done in less than 60 s, demonstrating the clinical feasibility. The frequency based method outperformed 4D total variation and PICCS on the simulated data, and for patients allowed for tumor location based on 60 s acquisitions, even for slowly breathing patients. It should thus be suitable for routine clinical use.
| S-EPMC7807579 | biostudies-literature
Project description:PurposeA clinical-prototype, dedicated, cone-beam breast computed tomography (CBBCT) system with offset detector is undergoing clinical evaluation at our institution. This study is to estimate the normalized glandular dose coefficients ( DgNCT ) that provide air kerma-to-mean glandular dose conversion factors using Monte Carlo simulations.Materials and methodsThe clinical prototype CBBCT system uses 49 kV x-ray spectrum with 1.39 mm 1st half-value layer thickness. Monte Carlo simulations (GATE, version 8) were performed with semi-ellipsoidal, homogeneous breasts of various fibroglandular weight fractions ( fg=0.01,0.15,0.5,1) , chest wall diameters ( d=8,10,14,18,20 cm), and chest wall to nipple length ( l=0.75d ), aligned with the axis of rotation (AOR) located at 65 cm from the focal spot to determine the DgNCT . Three geometries were considered - 40×30 -cm detector with no offset that served as reference and corresponds to a clinical CBBCT system, 30×30 -cm detector with 5 cm offset, and a 30×30 -cm detector with 10 cm offset.ResultsFor 5 cm lateral offset, the DgNCT ranged 0.177-0.574 mGy/mGy and reduction in DgNCT with respect to reference geometry was observed only for 18 cm ( 6.4%±0.23% ) and 20 cm ( 9.6%±0.22% ) diameter breasts. For the 10 cm lateral offset, the DgNCT ranged 0.221-0.581 mGy/mGy and reduction in DgNCT was observed for all breast diameters. The reduction in DgNCT was 1.4%±0.48% , 7.1%±0.13% , 17.5%±0.19% , 25.1%±0.15% , and 27.7%±0.08% for 8, 10, 14, 18, and 20 cm diameter breasts, respectively. For a given breast diameter, the reduction in DgNCT with offset-detector geometries was not dependent on fg . Numerical fits of DgNCTd,l,fg were generated for each geometry.ConclusionThe DgNCT and the numerical fit, DgNCTd,l,fg would be of benefit for current CBBCT systems using the reference geometry and for future generations using offset-detector geometry. There exists a potential for radiation dose reduction with offset-detector geometry, provided the same technique factors as the reference geometry are used, and the image quality is clinically acceptable.
| S-EPMC9007273 | biostudies-literature
Project description:To provide a proof of concept validation of a novel 4D cone-beam CT (4DCBCT) reconstruction algorithm and to determine the best methods to train and optimize the algorithm.The algorithm animates a patient fan-beam CT (FBCT) with a patient specific parametric motion model in order to generate a time series of deformed CTs (the reconstructed 4DCBCT) that track the motion of the patient anatomy on a voxel by voxel scale. The motion model is constrained by requiring that projections cast through the deformed CT time series match the projections of the raw patient 4DCBCT. The motion model uses a basis of eigenvectors that are generated via principal component analysis (PCA) of a training set of displacement vector fields (DVFs) that approximate patient motion. The eigenvectors are weighted by a parameterized function of the patient breathing trace recorded during 4DCBCT. The algorithm is demonstrated and tested via numerical simulation.The algorithm is shown to produce accurate reconstruction results for the most complicated simulated motion, in which voxels move with a pseudo-periodic pattern and relative phase shifts exist between voxels. The tests show that principal component eigenvectors trained on DVFs from a novel 2D/3D registration method give substantially better results than eigenvectors trained on DVFs obtained by conventionally registering 4DCBCT phases reconstructed via filtered backprojection.Proof of concept testing has validated the 4DCBCT reconstruction approach for the types of simulated data considered. In addition, the authors found the 2D/3D registration approach to be our best choice for generating the DVF training set, and the Nelder-Mead simplex algorithm the most robust optimization routine.
| S-EPMC3247929 | biostudies-literature
Project description:ObjectiveThis study aims to evaluate the feasibility of using cone beam computed tomography (CBCT) scans to assess the odontoid process diameter in the Arab population and to determine whether one or two cortical screws can be used for treating odontoid fractures.MethodsThe odontoid process of 142 individuals aged 12-75 years, including 72 males (mean age: 35.5) and 70 females (mean age: 36.2), were analyzed using CBCT scans. The sagittal and coronal CBCT views were used to evaluate the antero-posterior (AP) and transverse diameters of the odontoid process.ResultsMales had substantially bigger transverse and AP diameters of the odontoid process than females (p < 0.05 & P < 0.01 respectively). Among the sample, 97 individuals (67.4%) had external transverse diameter (METD) of less than 9 mm which is slightly bigger than that of Indians and 48 individuals (31.83%) had enough room for two 3.5 mm or two 2.7 mm screws as their METD was more than 9 mm like that of Greek and Turkish. Age had no significant impact on the morphometric measurements of the odontoid process.ConclusionMore than sixty percent of the sample had METDs of less than 9 millimeters, indicating that a single 4.5-mm Herbert screw may be suggested for fixing fractured odontoid processes in the Arab population.
| S-EPMC10215736 | biostudies-literature
Project description:Background and purposeThe limited image quality in Cone Beam CT (CBCT) stemming primarily from scattered radiation hinders accurate CBCT based dose calculation in radiotherapy. We investigated the use of a stoichiometric calibration for dose calculation on CBCT images of lung cancer patients.Materials and methodsCBCT calibrations were performed with thorax scan protocols, using a phantom with approximately the diameter of an average human thorax and a central cavity simulating the thoracic cavity. Thus scatter conditions resembling those in clinical thorax CBCT scans were simulated. A published stoichiometric parametrization was used. A treatment plan was simulated on CBCT and CT scans of an anthropomorphic phantom, the dose distributions were calculated, and clinically relevant DVH parameters were compared. Twelve lung cancer patients had surveillance CT scans (s-CT) taken twice during their treatment course in addition to daily setup CBCTs. Dose calculations were performed on the s-CTs and the corresponding CBCTs taken on the same day, and DVH parameters were compared.ResultsEighty percent of CBCT DVH parameters found for the phantom were within ±1% of CT doses, and 98% were within ±3%. For patients, the median CT/CBCT dose difference was within ±2%, and 98% of DVH parameters were within ±4%. Minimum dose to the tumor was underestimated (median 1.9%) on CBCT, while maximum doses to most organs at risk were slightly overestimated.ConclusionDirect dose calculations on CBCTs of lung cancer patients were feasible within ∼4% accuracy using a simple calibration method, which is easily implemented in a clinical setting.
| S-EPMC7807659 | biostudies-literature
Project description:Pulmonary nodules with intermediate to high risk of malignancy should preferably be diagnosed with image guide minimally invasive diagnostics before treatment. Several technological innovations have been developed to endobronchially navigate to these lesions and obtain tissue for diagnosis. This review addresses these technological advancements in navigation bronchoscopy in three basic steps: navigation, position confirmation and acquisition, with a specific focus on cone-beam computed tomography (CBCT). For navigation purposes ultrathin bronchoscopy combined with virtual bronchoscopy navigation, electromagnetic navigation and robotic assisted bronchoscopy all achieve good results as a navigation guidance tool, but cannot confirm location or guide biopsy positioning. Diagnostic yield has seen improvement by combining these techniques with a secondary imaging tool like radial endobronchial ultrasound (rEBUS) and fluoroscopy. For confirmation of lesion access, rEBUS provides local detailed ultrasound-imaging and can be used to confirm lesion access in combination with fluoroscopy, measure nodule-contact area length and determine catheter position for sampling. CBCT is the only technology that can provide precise 3D positioning confirmation. When focusing on tissue acquisition, there is often more than 10% difference between reaching the target and getting a diagnosis. This discrepancy is multifactorial and caused by breathing movements, small samples sizes, instrument tip displacements by tool rigidity and tumour inhomogeneity. Yield can be improved by targeting fluorodeoxyglucose (FDG)-avid regions, immediate feedback of rapid onsite evaluation, choosing sampling tools with different passive stiffnesses, by increasing the number biopsies taken and (future) catheter modifications like (robotic assisted-) active steering. CBCT with augmented fluoroscopy (CBCT-AF) based navigation bronchoscopy combines navigation guidance with 3D-image confirmation of instrument-in-lesion positioning in one device. CBCT-AF allows for overlaying the lesion and navigation pathway and the possibility to outline trans-parenchymal pathways. It can help guide and verify sampling in 3D in near real-time. Disadvantages are the learning curve, the inherent use of radiation and limited availability/access to hybrid theatres. A mobile C-arm can provide 3D imaging, but lower image quality due to lower power and lower contrast-to-noise ratio is a limiting factor. In conclusion, a multi-modality approach in experienced hands seems the best option for achieving a diagnostic accuracy >85%. Either adequate case selection or detailed 3D imaging are essential to obtain high accuracy. For current and future transbronchial treatments, high-resolution (CBCT) 3D-imaging is essential.
| S-EPMC10477635 | biostudies-literature
Project description:Stiffness and shear moduli of human trabecular bone may be analyzed in vivo by finite element (FE) analysis from image data obtained by clinical imaging equipment such as high resolution peripheral quantitative computed tomography (HR-pQCT). In clinical practice today, this is done in the peripheral skeleton like the wrist and heel. In this cadaveric bone study, fourteen bone specimens from the wrist were imaged by two dental cone beam computed tomography (CBCT) devices and one HR-pQCT device as well as by dual energy X-ray absorptiometry (DXA). Histomorphometric measurements from micro-CT data were used as gold standard. The image processing was done with an in-house developed code based on the automated region growing (ARG) algorithm. Evaluation of how well stiffness (Young's modulus E3) and minimum shear modulus from the 12, 13, or 23 could be predicted from the CBCT and HR-pQCT imaging data was studied and compared to FE analysis from the micro-CT imaging data. Strong correlations were found between the clinical machines and micro-CT regarding trabecular bone structure parameters, such as bone volume over total volume, trabecular thickness, trabecular number and trabecular nodes (varying from 0.79 to 0.96). The two CBCT devices as well as the HR-pQCT showed the ability to predict stiffness and shear, with adjusted R2-values between 0.78 and 0.92, based on data derived through our in-house developed code based on the ARG algorithm. These findings indicate that clinically used CBCT may be a feasible method for clinical studies of bone structure and mechanical properties in future osteoporosis research.
| S-EPMC4981445 | biostudies-literature
Project description:BackgroundMinimally invasive surgery (MIS) for evacuation of spontaneous intracerebral hemorrhage (ICH) has shown promise but there remains a need for intraoperative performance assessment considering the wide range of evacuation effectiveness. In this feasibility study, we analyzed the benefit of intraoperative 3-dimensional imaging during navigated endoscopy-assisted ICH evacuation by mechanical clot fragmentation and aspiration.Methods18 patients with superficial or deep supratentorial ICH underwent MIS for clot evacuation followed by intraoperative computerized tomography (iCT) or cone-beam CT (CBCT) imaging. Eligibility for MIS required (a) availability of intraoperative iCT or CBCT, (b) spontaneous lobar or deep ICH without vascular pathology, (c) a stable ICH volume (20-90 ml), (d) a reduced level of consciousness (GCS 5-14), and (e) a premorbid mRS ≤ 1. Demographic, clinical, and radiographic patient data were analyzed by two independent observers.ResultsNine female and 9 male patients with a median age of 76 years (42-85) presented with an ICH score of 3 (1-4), GCS of 10 (5-14) and ICH volume of 54 ± 26 ml. Clot fragmentation and aspiration was feasible in all cases and intraoperative imaging determined an overall evacuation rate of 80 ± 19% (residual hematoma volume: 13 ± 17 ml; p < 0.0001 vs. Pre-OP). Based on the intraoperative imaging results, 1/3rd of all patients underwent an immediate re-aspiration attempt. No patient experienced hemorrhagic complications or required conversion to open craniotomy. However, routine postoperative CT imaging revealed early hematoma re-expansion with an adjusted evacuation rate of 59 ± 30% (residual hematoma volume: 26 ± 37 ml; p < 0.001 vs. Pre-OP).ConclusionsRoutine utilization of iCT or CBCT imaging in MIS for ICH permits direct surgical performance assessment and the chance for immediate re-aspiration, which may optimize targeting of an ideal residual hematoma volume and reduce secondary revision rates.
| S-EPMC7593312 | biostudies-literature