Dataset Information

Finite Element Analysis and Biomechanical Comparison of Short Posterior Spinal Instrumentation with Divergent Bridge Construct versus Parallel Tension Band Construct for Thoracolumbar Spine Fractures.

ABSTRACT: The ideal treatment for unstable thoracolumbar fractures remains controversial with posterior reduction and stabilization, anterior reduction and stabilization, combined posterior and anterior reduction and stabilization, and even nonoperative management advocated. Short segment posterior osteosynthesis of these fractures has less comorbidities compared with the other operative approaches but settles into kyphosis over time. Biomechanical comparison of the divergent bridge construct versus the parallel tension band construct was performed for anteriorly destabilized T11-L1 spine segments using three different models: (1) finite element analysis (FEA), (2) a synthetic model, and (3) a human cadaveric model. Outcomes measured were construct stiffness and ultimate failure load. Our objective was to determine if the divergent pedicle screw bridge construct would provide more resistance to kyphotic deforming forces. All three modalities showed greater stiffness with the divergent bridge construct. The FEA calculated a stiffness of 21.6 N/m for the tension band construct versus 34.1 N/m for the divergent bridge construct. The synthetic model resulted in a mean stiffness of 17.3 N/m for parallel tension band versus 20.6 N/m for the divergent bridge (p = 0.03), whereas the cadaveric model had an average stiffness of 15.2 N/m in the parallel tension band compared with 18.4 N/m for the divergent bridge (p = 0.02). Ultimate failure load with the cadaveric model was found to be 622 N for the divergent bridge construct versus 419 N (p = 0.15) for the parallel tension band construct. This study confirms our clinical experience that the short posterior divergent bridge construct provides greater stiffness for the management of unstable thoracolumbar fractures.

SUBMITTER: Ouellet JA

PROVIDER: S-EPMC3854578 | biostudies-other | 2013 Jun

REPOSITORIES: biostudies-other

ACCESS DATA

Similar Datasets

Project description:BackgroundIn the follow-up after internal fixation of thoracolumbar fractures, the imaging of some patients shows "crater-like" collapse of the superior endplate of the injured vertebra, with variable collapse area and depth, even involving the anterior edge of the vertebral body. Though many papers had described the phenomenon, but nearly no one did biomechanical research about this. So we did this research in a creative way by using finite element model.MethodsA healthy male volunteer was selected. The 64-slice thin-section spiral computed tomography images at the level of T11-L3 were collected. Data were imported into Mimics 15.0 medical image processing software to establish three-dimensional finite element skeletal models of T11 to L3 containing only three-dimensional surface elements without entities. The model was assigned values and verified. Then the pedicle screw-rod system was added to this model, and five models containing the screw-rod system with different defect sizes as well as five models that simulated the removal of the screw-rod system were derived at the same time (the defect volume was 1/5, 2/5, 3/5, 4/5, or 5/5 of the anterior vertebral column, respectively). Biomechanical analysis was then performed on this basis.ResultsAfter the removal of the internal fixator, as defect volume increased, the stress difference between the 4/5 defect group and the 5/5 defect group had the greatest magnitude of combined stress under the seven working conditions. When the volume of the collapse defect reached 4/5 of the anterior column of the vertebral body, the concentration of stress increased significantly, suggesting that the risk of continued compression or even refracture of the injured vertebra increased if the internal fixator was removed at that time.ConclusionsWhen the volume of the defect in the superior endplate of the injured vertebra reaches 4/5 of the anterior column, the removal of the internal fixator should be carefully considered to avoid refracture of the anterior column of the injured vertebra.

Project description:ObjectiveThe aim of this study was to verify the biomechanical properties of a newly designed angulated lateral plate (mini-LP) suited for two-level oblique lumbar interbody fusion (OLIF). The mini-LP is placed through the lateral ante-psoas surgical corridor, which reduces the operative time and complications associated with prolonged anesthesia and placement in the prone position.MethodsA three-dimensional nonlinear finite element (FE) model of an intact L1-L5 lumbar spine was constructed and validated. The intact model was modified to generate a two-level OLIF surgery model augmented with three types of lateral fixation (stand-alone, SA; lateral rod screw, LRS; miniature lateral plate, mini-LP); the operative segments were L2-L3 and L3-L4. By applying a 500 N follower load and 7.5 Nm directional moment (flexion-extension, lateral bending, and axial rotation), all models were used to simulate human spine movement. Then, we extracted the range of motion (ROM), peak contact force of the bony endplate (PCFBE), peak equivalent stress of the cage (PESC), peak equivalent stress of fixation (PESF), and stress contour plots.ResultsWhen compared with the intact model, the SA model achieved the least reduction in ROM to surgical segments in all motions. The ROM of the mini-LP model was slightly smaller than that of the LRS model. There were no significant differences in surgical segments (L1-L2, L4-L5) between all surgical models and the intact model. The PCFBE and PESC of the LRS and the mini-LP fixation models were lower than those of the SA model. However, the differences in PCFBE or PESC between the LRS- and mini-LP-based models were not significant. The fixation stress of the LRS- and mini-LP-based models was significantly lower than the yield strength under all loading conditions. In addition, the variances in the PESF in the LRS- and mini-LP-based models were not obvious.ConclusionOur biomechanical FE analysis indicated that LRS or mini-LP fixation can both provide adequate biomechanical stability for two-level OLIF through a single incision. The newly designed mini-LP model seemed to be superior in installation convenience, and equally good outcomes were achieved with both LRS and mini-LP for two-level OLIF.

Project description:PurposeThe purpose of this study was to investigate finite element biomechanical properties of the novel transpedicular transdiscal (TPTD) screw fixation with interbody arthrodesis technique in lumbar spine.MethodsAn L4-L5 finite element model was established and validated. Then, two fixation models, TPTD screw system and bilateral pedicle screw system (BPSS), were established on the validated L4-L5 finite element model. The inferior surface of the L5 vertebra was set immobilised, and moment of 7.5 Nm was applied on the L4 vertebra to test the range of motion (ROM) and stress at flexion, extension, lateral bending and axial rotation.ResultsThe intact model was validated for prediction accuracy by comparing two previously published studies. Both of TPTD and BPSS fixation models displayed decreased motion at L4-L5. The ROMs of six moments of flexion, extension, left lateral bending, right lateral bending, left axial rotation and right axial rotation in TPTD model were 1.92, 2.12, 1.10, 1.11, 0.90 and 0.87°, respectively; in BPSS model, they were 1.48, 0.42, 0.35, 0.38, 0.74 and 0.75°, respectively. The screws' peak stress of above six moments in TPTD model was 182.58, 272.75, 133.01, 137.36, 155.48 and 150.50 MPa, respectively; and in BPSS model, it was 103.16, 129.74, 120.28, 134.62, 180.84 and 169.76 MPa, respectively.ConclusionBoth BPSS and TPTD can provide stable biomechanical properties for lumbar spine. The decreased ROM of flexion, extension and lateral bending was slightly more in BPSS model than in TPTD model, but TPTD model had similar ROM of axial rotation with BPSS model. The screws' peak stress of TPTD screw focused on the L4-L5 intervertebral space region, and more caution should be put at this site for the fatigue breakage.The translational potential of this articleOur finite element study provides the biomechanical properties of novel TPTD screw fixation, and promotes this novel transpedicular transdiscal screw fixation with interbody arthrodesis technique be used clinically.

Project description:Posterior screw-rod constructs can be used to stabilize spinal segments; however, the stiffness is not absolute, and some motion can persist. While the effect of crosslink-augmentation has been evaluated in multiple studies, the fundamental explanation of their effectiveness has not been investigated. The aim of this study was to quantify the parameters "screw rotation" and "parallelogram deformation" in posterior instrumentations with and without crosslinks to analyze and explain their fundamental effect. Biomechanical testing of 15 posteriorly instrumented human spinal segments (Th10/11-L4/L5) was conducted in axial rotation, lateral bending, and flexion-extension with ± 7.5 Nm. Screw rotation and parallelogram deformation were compared for both configurations. Parallelogram deformation occurred predominantly during axial rotation (2.6°) and was reduced by 60% (-1.45°, p = 0.02) by the addition of a crosslink. Simultaneously, screw rotation (0.56°) was reduced by 48% (-0.27°, p = 0.02) in this loading condition. During lateral bending, 0.38° of parallelogram deformation and 1.44° of screw rotation was measured and no significant reduction was achieved by crosslink-augmentation (8%, -0.03°, -p = 0.3 and -13%, -0.19°, p = 0.7 respectively). During flexion-extension, parallelogram deformation was 0.4° and screw rotation was 0.39° and crosslink-augmentation had no significant effect on these values (-0.12°, -30%, p = 0.5 and -0°, -0%, p = 0.8 respectively). In axial rotation, crosslink-augmentation can reduce parallelogram deformation and with that, screw rotation. In lateral bending and flexion-extension parallelogram deformation is minimal and crosslink-augmentation has no significant effect. Since the relatively large screw rotation in lateral bending is not caused by parallelogram deformation, crosslink-augmentation is no adequate countermeasure. The fundamental understanding of the biomechanical effect of crosslink-augmentation helps better understand its potential and limitations in increasing construct stiffness.

Project description:PurposeMany minimally invasive surgical (MIS) techniques have been developed for instrumentation of spine. These MIS techniques restore stability, alignment while achieving return to function quite early as compared to open spine surgeries. The main aim of this review was to evaluate role, indications and complications of these MIS techniques in Thoracolumbar and Lumbar fractures.MethodsPubmed search using key words such as"Percutaneous pedicle screw for Thoracolumbar fractures" and "Video Assisted Thoracoscopy, Thoracoscopic, VATS for thoracolumbar, Lumbar and Spine fractures" were used till July 2016 while doing literature search. Authors analyzed all the articles, which came after search; the articles relevant to the topic were selected and used for the study. Both prospective and retrospective case control studies and randomized control trials (RCT's) were included in this review. Case reports and reviews were excluded. Studies demonstrating use of MIS in cases other than spine trauma and studies with lack of clinical follow up were excluded from this review. Variables such as number of patients, operative time and complications were evaluated in each study.ResultsAfter pubmed search, we found total 68 studies till July 2016 out of which eight studies were relevant for analysis of Video Assisted Thoracoscopy for thoracolumbar and lumbar fractures. Total 72 articles for Percutaneous pedicle screws in thoracolumbar and lumbar fractures were retrieved out of which percutaneous pedicle screws were analyzed in eleven studies and twelve studies involved comparison of percutaneous pedicle screws and conventional open techniques.ConclusionRole and Indications of the MIS techniques in spinal trauma are expanding quite rapidly. MIS techniques restore stability, alignment while achieving early return to function and lower infection rates as compared to open spine surgeries. In long term, they provide good kyphosis correction and stable fixation and fusion of spine. They are associated with long learning curve and technical challenges but with careful patient selection and in expert hands, MIS techniques may produce better results than open trauma spine surgeries.

Dataset Information

Finite Element Analysis and Biomechanical Comparison of Short Posterior Spinal Instrumentation with Divergent Bridge Construct versus Parallel Tension Band Construct for Thoracolumbar Spine Fractures.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets