Fabrication and electrical properties of stacked graphene monolayers.
Ontology highlight
ABSTRACT:
SUBMITTER: Chen JJ
PROVIDER: S-EPMC4033920 | biostudies-other | 2014
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Impregnation of expandable graphite (EG) after thermal treatment with an epoxy resin containing surface-active agents (SAAs) enhanced the intercalation of epoxy monomer between EG layers and led to further exfoliation of the graphite, resulting in stacks of few graphene layers, so-called "stacked" graphene (SG). This process enabled electrical conductivity of cured epoxy/SG composites at lower percolation thresholds, and improved thermo-mechanical properties were measured with either Kevlar, carbon or glass-fiber-reinforced composites. Several compositions with SAA-modified SG led to higher dynamic moduli especially at high temperatures, reflecting the better wetting ability of the modified nanoparticles. The hydrophilic/hydrophobic nature of the SAA dictates the surface energy balance. More hydrophilic SAAs promoted localization of the SG at the Kevlar/epoxy interface, and morphology seems to be driven by thermodynamics, rather than the kinetic effect of viscosity. This effect was less obvious with carbon or glass fibers, due to the lower surface energy of the carbon fibers or some incompatibility with the glass-fiber sizing. Proper choice of the surfactant and fine-tuning of the crosslink density at the interphase may provide further enhancements in thermo-mechanical behavior.
| S-EPMC5629411 | biostudies-literature
Project description:Hybrid nanomaterials based on graphene and PbS quantum dots (QDs) have demonstrated promising applications in optoelectronics. However, the formation of high-quality large-area hybrid films remains technologically challenging. Here, we demonstrate that ligand-assisted self-organization of covalently bonded PbS QDs and reduced graphene oxide (rGO) can be utilized for the formation of highly uniform monolayers. After the post-deposition ligand exchange, these films demonstrated high conductivity and photoresponse. The obtained films demonstrate a remarkable improvement in morphology and charge transport compared to those obtained by the spin-coating method. It is expected that these materials might find a range of applications in photovoltaics and optoelectronics.
| S-EPMC7221828 | biostudies-literature
Project description:The performance of devices and systems based on two-dimensional material systems depends critically on the quality of the contacts between 2D material and metal. A low contact resistance is an imperative requirement to consider graphene as a candidate material for electronic and optoelectronic devices. Unfortunately, measurements of contact resistance in the literature do not provide a consistent picture, due to limitations of current graphene technology, and to incomplete understanding of influencing factors. Here we show that the contact resistance is intrinsically dependent on graphene sheet resistance and on the chemistry of the graphene-metal interface. We present a physical model of the contacts based on ab-initio simulations and extensive experiments carried out on a large variety of samples with different graphene-metal contacts. Our model explains the spread in experimental results as due to uncontrolled graphene doping and suggests ways to engineer contact resistance. We also predict an achievable contact resistance of 30 Ω·μm for nickel electrodes, extremely promising for applications.
| S-EPMC5506027 | biostudies-literature
Project description:Graphene has been received a considerable amount of attention as a transparent conducting electrode (TCE) which may be able to replace indium tin oxide (ITO) to overcome the significant weakness of the poor flexibility of ITO. Given that graphene is the thinnest 2-dimensional (2D) material known, it shows extremely high flexibility, and its lateral periodic honeycomb structure of sp(2)-bonded carbon atoms enables ~2.3% of incident light absorption per layer. However, there is a trade-off between the electrical resistance and the optical transmittance, and the fixed absorption rate in graphene limits is use when fabricating devices. Therefore, a more efficient method which continuously controls the optical and electrical properties of graphene is needed. Here, we introduce a method which controls the optical transmittance and the electrical resistance of graphene through various thicknesses of the top Cu layers with a Cu/Ni metal catalyst structure used to fabricate a planar mesh pattern of single and multi-layer graphene. We exhibit a continuous transmittance change from 85% (MLG) to 97.6% (SLG) at an incident light wavelength of 550 nm on graphene samples simultaneously grown in a CVD quartz tube. We also investigate the relationships between the sheet resistances.
| S-EPMC4832197 | biostudies-literature
Project description:We fabricated the stacked bilayer molybdenum disulfide (MoS2) by using reduced graphene oxide (rGO) as a spacer for increasing the optoelectronic properties of MoS2. The rGO can decrease the interlayer coupling between the stacked bilayer MoS2 and retain the direct band gap property of MoS2. We observed a twofold enhancement of the photoluminescence intensity of the stacked MoS2 bilayer. In the Raman scattering, we observed that the E12g and A1g modes of the stacked bilayer MoS2 with rGO were further shifted compared to monolayer MoS2, which is due to the van der Waals (vdW) interaction and the strain effect between the MoS2 and rGO layers. The findings of this study will expand the applicability of monolayer MoS2 for high-performance optoelectronic devices by enhancing the optical properties using a vdW spacer.
| S-EPMC6459906 | biostudies-literature
Project description:Semi-infinite single-atom-thick graphene is an ideal reinforcing material that can simultaneously improve the mechanical, electrical, and thermal properties of matrix. Here, we present a float-stacking strategy to accurately align the monolayer graphene reinforcement in polymer matrix. We float graphene-poly(methylmethacrylate) (PMMA) membrane (GPM) at the water-air interface, and wind-up layer-by-layer by roller. During the stacking process, the inherent water meniscus continuously induces web tension of the GPM, suppressing wrinkle and folding generation. Moreover, rolling-up and hot-rolling mill process above the glass transition temperature of PMMA induces conformal contact between each layer. This allows for pre-tension of the composite, maximizing its reinforcing efficiency. The number and spacing of the embedded graphene fillers are precisely controlled. Notably, we accurately align 100 layers of monolayer graphene in a PMMA matrix with the same intervals to achieve a specific strength of about 118.5 MPa g-1 cm3, which is higher than that of lightweight Al alloy, and a thermal conductivity of about 4.00 W m-1 K-1, which is increased by about 2,000 %, compared to the PMMA film.
| S-EPMC10928174 | biostudies-literature
Project description:Two-dimensional (2D) nanosheets show promise for the development of water treatment membranes with extraordinary separation properties and the advantages of atomic thickness with micrometer-sized lateral dimensions. Stacked graphene oxide (GO)-based membranes can demonstrate unique molecular sieving properties with fast water permeation. However, improvements to the structural stability of the membranes in water to avoid problems such as swelling, disruption of the ordered GO layer and decreased rejection are crucial issues. This study reports the fabrication of stacked GO nanosheet membranes by simple vacuum filtration using triethanolamine (TEOA) as a crosslinker and mild reducing agent for improved structural stability and membrane performance. Results show that GO membranes modified with TEOA (GO-TEOA membranes) have a higher structural stability in water than unmodified GO membranes, resulting in improved salt rejection performance. Furthermore, GO-TEOA membranes show stable water permeance at applied pressures up to 9 bar with Na?SO? rejection of 85%, suggesting the potential benefits for water treatment applications.
| S-EPMC6315452 | biostudies-literature
Project description:Dry-spinning method is extensively employed in fiber industry, comparing to the counter-part of wet-spinning process, it has advantages of environmentally friendly, high yield rate and no need for purification. Here, we report the synthesis of graphene oxide (GO) fibers via dry spinning GO inks with extremely high concentrations. The proper rheology properties of such GO inks allow us to dry spin GO fiber directly. Various dry spinning conditions are investigated, and the relationship between mechanical performance and micro-structure of the obtained GO fiber are established. We found that the existence of larger GO liquid crystal domains does not necessarily result to higher mechanical properties, and it is because those large GO liquid crystal domains evolve into thick GO films during drying process and thus prevent the intimate compaction of the whole GOF and leave behind gaps. This is detrimental for the mechanical properties, and thus the dry spin GOF are much weaker than that of wet spin ones. Importantly, Barus effects, that generally arise during the melt spinning of polymers, were not observed, indicating that caution must be taken when classical polymer rheology theories are applied to investigate the dynamic behaviors of GO solution.
| S-EPMC6050277 | biostudies-literature
Project description:The performance of graphene devices is often limited by defects and impurities induced during device fabrication. Polymer residue left on the surface of graphene after photoresist processing can increase electron scattering and hinder electron transport. Furthermore, exposing graphene to plasma-based processing such as sputtering of metallization layers can increase the defect density in graphene and alter the device performance. Therefore, the preservation of the high-quality surface of graphene during thin-film deposition and device manufacturing is essential for many electronic applications. Here, we show that the use of self-assembled monolayers (SAMs) of hexamethyldisilazane (HMDS) as a buffer layer during the device fabrication of graphene can significantly reduce damage, improve the quality of graphene, and enhance device performance. The role of HMDS has been systematically investigated using surface analysis techniques and electrical measurements. The benefits of HMDS treatment include a significant reduction in defect density compared with as-treated graphene and more than a 2-fold reduction of contact resistance. This surface treatment is simple and offers a practical route for improving graphene device interfaces, which is important for the integration of graphene into functional devices such as electronics and sensor devices.
| S-EPMC7905810 | biostudies-literature
Project description:Structural defects strongly impact the electrical transport properties of graphene nanostructures. In this Perspective, we give a brief overview of different types of defects in graphene and their effect on transport properties. We discuss recent experimental progress on graphene self-repair of defects, with a focus on in situ transmission electron microscopy studies. Finally, we present the outlook for graphene self-repair and in situ experiments.
| S-EPMC4415450 | biostudies-other