Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Light-output enhancement of GaN-based light-emitting diodes with three-dimensional backside reflectors patterned by microscale cone array.

ABSTRACT: Three-dimensional (3D) backside reflector, compared with flat reflectors, can improve the probability of finding the escape cone for reflecting lights and thus enhance the light-extraction efficiency (LEE) for GaN-based light-emitting diode (LED) chips. A triangle-lattice of microscale SiO2 cone array followed by a 16-pair Ti3O5/SiO2 distributed Bragg reflector (16-DBR) was proposed to be attached on the backside of sapphire substrate, and the light-output enhancement was demonstrated by numerical simulation and experiments. The LED chips with flat reflectors or 3D reflectors were simulated using Monte Carlo ray tracing method. It is shown that the LEE increases as the reflectivity of backside reflector increases, and the light-output can be significantly improved by 3D reflectors compared to flat counterparts. It can also be observed that the LEE decreases as the refractive index of the cone material increases. The 3D 16-DBR patterned by microscale SiO2 cone array benefits large enhancement of LEE. This microscale pattern was prepared by standard photolithography and wet-etching technique. Measurement results show that the 3D 16-DBR can provide 12.1% enhancement of wall-plug efficiency, which is consistent with the simulated value of 11.73% for the enhancement of LEE.

SUBMITTER: Huang H

PROVIDER: S-EPMC4124249 | biostudies-other | 2014

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Transfer-printed, tandem microscale light-emitting diodes for full-color displays.

Project description:Inorganic semiconductor-based microscale light-emitting diodes (micro-LEDs) have been widely considered the key solution to next-generation, ubiquitous lighting and display systems, with their efficiency, brightness, contrast, stability, and dynamic response superior to liquid crystal or organic-based counterparts. However, the reduction of micro-LED sizes leads to the deteriorated device performance and increased difficulties in manufacturing. Here, we report a tandem device scheme based on stacked red, green, and blue (RGB) micro-LEDs, for the realization of full-color lighting and displays. Thin-film micro-LEDs (size ∼100 μm, thickness ∼5 μm) based on III-V compound semiconductors are vertically assembled via epitaxial liftoff and transfer printing. A thin-film dielectric-based optical filter serves as a wavelength-selective interface for performance enhancement. Furthermore, we prototype arrays of tandem RGB micro-LEDs and demonstrate display capabilities. These materials and device strategies provide a viable path to advanced lighting and display systems.

| S-EPMC8106345 | biostudies-literature

Stable and efficient transfer-printing including repair using a GaN-based microscale light-emitting diode array for deformable displays.

Project description:GaN-based microscale light-emitting diodes (μLEDs) are reported for assembly into deformable displays and repair systems. A stamp-imprinting method that enables large area assembly without spatial limitation is involved in the system, and a selective pick-up method is presented that includes a method for removing detected defective chips through micro-pulsed laser scanning. The photosensitive functional material, which is an accepted layer for the stable imprinting of chips, is determined by controlling the adhesion. In addition, selective pick-up and adhesion-controlled functional materials allow the implementation of defect-free displays through two pick-and-place cycles. Displays and related systems fabricated with this method can offer interesting optical and electrical properties.

| S-EPMC6689111 | biostudies-literature

Ultraviolet GaN Light-Emitting Diodes with Porous-AlGaN Reflectors.

Project description:A GaN/AlGaN ultraviolet light emitting diode (UV-LED) structure with a porous AlGaN reflector structure has been demonstrated. Inside the UV-LED, the n+-AlGaN/undoped-AlGaN stack structure was transformed into a porous-AlGaN/undoped-AlGaN stack structure through a doping-selective electrochemical etching process. The reflectivity of the porous AlGaN reflector was 93% at 374 nm with a stop-bandwidth of 35 nm. In an angle-dependent reflectance measurement, the central wavelength of the porous AlGaN reflector had blueshift phenomenon by increasing light-incident angle from 10° to 50°. A cut-off wavelength was observed at 349 nm due to the material absorption of the porous-AlGaN/u-AlGaN stack structure. In the treated UV-LED structure, the photoluminescence emission wavelength was measured at 362 nm with a 106° divergent angle covered by the porous-AlGaN reflector. The light output power of the treated UV-LED structure was higher than that of the non-treated UV-LED structure due to the high light reflectance on the embedded porous AlGaN reflector.

| S-EPMC5504019 | biostudies-other

Efficient sky-blue perovskite light-emitting diodes via photoluminescence enhancement.

Project description:The efficiencies of green and red perovskite light-emitting diodes (PeLEDs) have been increased close to their theoretical upper limit, while the efficiency of blue PeLEDs is lagging far behind. Here we report enhancing the efficiency of sky-blue PeLEDs by overcoming a major hurdle of low photoluminescence quantum efficiency in wide-bandgap perovskites. Blending phenylethylammonium chloride into cesium lead halide perovskites yields a mixture of two-dimensional and three-dimensional perovskites, which enhances photoluminescence quantum efficiency from 1.1% to 19.8%. Adding yttrium (III) chloride into the mixture further enhances photoluminescence quantum efficiency to 49.7%. Yttrium is found to incorporate into the three-dimensional perovskite grain, while it is still rich at grain boundaries and surfaces. The yttrium on grain surface increases the bandgap of grain shell, which confines the charge carriers inside grains for efficient radiative recombination. Record efficiencies of 11.0% and 4.8% were obtained in sky-blue and blue PeLEDs, respectively.

| S-EPMC6904584 | biostudies-literature

Effects of GaN/AlGaN/Sputtered AlN nucleation layers on performance of GaN-based ultraviolet light-emitting diodes.

Project description:We report on the demonstration of GaN-based ultraviolet light-emitting diodes (UV LEDs) emitting at 375 nm grown on patterned sapphire substrate (PSS) with in-situ low temperature GaN/AlGaN nucleation layers (NLs) and ex-situ sputtered AlN NL. The threading dislocation (TD) densities in GaN-based UV LEDs with GaN/AlGaN/sputtered AlN NLs were determined by high-resolution X-ray diffraction (XRD) and cross-sectional transmission electron microscopy (TEM), which revealed that the TD density in UV LED with AlGaN NL was the highest, whereas that in UV LED with sputtered AlN NL was the lowest. The light output power (LOP) of UV LED with AlGaN NL was 18.2% higher than that of UV LED with GaN NL owing to a decrease in the absorption of 375 nm UV light in the AlGaN NL with a larger bandgap. Using a sputtered AlN NL instead of the AlGaN NL, the LOP of UV LED was further enhanced by 11.3%, which is attributed to reduced TD density in InGaN/AlInGaN active region. In the sputtered AlN thickness range of 10-25 nm, the LOP of UV LED with 15-nm-thick sputtered AlN NL was the highest, revealing that optimum thickness of the sputtered AlN NL is around 15 nm.

| S-EPMC5353678 | biostudies-literature

Defect-selective-etched porous GaN as a buffer layer for high efficiency InGaN/GaN light-emitting diodes.

Project description:Substrate-induced biaxial compressive stress and threading dislocations (TDs) have been recognized to severely impair the performance, stability, and reliability of InGaN/GaN light-emitting diodes (LEDs) for quite some time. In this study, a defect-selective-etched (DSE) porous GaN layer is fabricated employing electro-chemical etching and applied as a buffer layer for the development of InGaN/GaN LEDs with high quantum efficiency. Based on the analysis of photoluminescence and micro-Raman spectra, it has been revealed that the overgrown GaN epilayer on the DSE porous GaN has a relatively low TDs and relaxation of compressive stress in comparison to the conventional GaN epilayer. The remarkable improvement in the internal quantum efficiency of the InGaN/GaN LEDs is directly attributable to the strong radiative recombination in InGaN/GaN multi-quantum-wells caused by stress relaxation and TDs annihilation. Our findings indicate that the use of DSE porous GaN as a buffer layer may be a viable approach for producing crystalline GaN epilayers and high-performance LEDs.

| S-EPMC9671350 | biostudies-literature

Less strained and more efficient GaN light-emitting diodes with embedded silica hollow nanospheres.

Project description:Light-emitting diodes (LEDs) become an attractive alternative to conventional light sources due to high efficiency and long lifetime. However, different material properties between GaN and sapphire cause several problems such as high defect density in GaN, serious wafer bowing, particularly in large-area wafers, and poor light extraction of GaN-based LEDs. Here, we suggest a new growth strategy for high efficiency LEDs by incorporating silica hollow nanospheres (S-HNS). In this strategy, S-HNSs were introduced as a monolayer on a sapphire substrate and the subsequent growth of GaN by metalorganic chemical vapor deposition results in improved crystal quality due to nano-scale lateral epitaxial overgrowth. Moreover, well-defined voids embedded at the GaN/sapphire interface help scatter lights effectively for improved light extraction, and reduce wafer bowing due to partial alleviation of compressive stress in GaN. The incorporation of S-HNS into LEDs is thus quite advantageous in achieving high efficiency LEDs for solid-state lighting.

| S-EPMC3826094 | biostudies-literature

Remote heteroepitaxy of GaN microrod heterostructures for deformable light-emitting diodes and wafer recycle.

Project description:There have been rapidly increasing demands for flexible lighting apparatus, and micrometer-scale light-emitting diodes (LEDs) are regarded as one of the promising lighting sources for deformable device applications. Herein, we demonstrate a method of creating a deformable LED, based on remote heteroepitaxy of GaN microrod (MR) p-n junction arrays on c-Al2O3 wafer across graphene. The use of graphene allows the transfer of MR LED arrays onto a copper plate, and spatially separate MR arrays offer ideal device geometry suitable for deformable LED in various shapes without serious device performance degradation. Moreover, remote heteroepitaxy also allows the wafer to be reused, allowing reproducible production of MR LEDs using a single substrate without noticeable device degradation. The remote heteroepitaxial relation is determined by high-resolution scanning transmission electron microscopy, and the density functional theory simulations clarify how the remote heteroepitaxy is made possible through graphene.

| S-EPMC7269673 | biostudies-literature

High-efficiency and high-resolution patterned quantum dot light emitting diodes by electrohydrodynamic printing.

Project description:The development of quantum dot light-emitting diode (QLED) fabrication technologies for high-definition and low-cost displays is an important research topic. However, commercially available piezoelectric inkjet printing has reached its limit in reducing pixel sizes, which restricts its potential use in high-resolution displays. Here, we exhibit an electrohydrodynamic (EHD) printing method for manufacturing QLEDs with a high resolution of 500 ppi that remarkably surpasses the resolution of conventional inkjet printing displays. By optimizing the EHD printing process, a high-resolution pixelated bottom-emitting passive matrix QLED with a maximal current efficiency of 14.4 cd A-1 in a pixel size of 5 μm × 39 μm was achieved, indicating the capability of the EHD method in superfine printing and high efficiency QLED. Moreover, a top-emitting device is designed using a capping layer; the maximal current efficiency of top-emission passive matrix QLED devices can reach up to 16.5 cd A-1. Finally, a two-color (red and green) bottom-emission QLED device with 500 ppi was fabricated. The successful fabrication of these high-efficiency QLEDs with 500 ppi demonstrated that the EHD printing strategy has numerous potential applications in high-resolution and high-performance QLEDs for a range of applications, such as mobile or wearable devices.

| S-EPMC9926896 | biostudies-literature

Vacuum nanohole array embedded phosphorescent organic light emitting diodes.

Project description:Light extraction from organic light-emitting diodes that utilize phosphorescent materials has an internal efficiency of 100% but is limited by an external quantum efficiency (EQE) of 30%. In this study, extremely high-efficiency organic light emitting diodes (OLEDs) with an EQE of greater than 50% and low roll-off were produced by inserting a vacuum nanohole array (VNHA) into phosphorescent OLEDs (PhOLEDs). The resultant extraction enhancement was quantified in terms of EQE by comparing experimentally measured results with those produced from optical modeling analysis, which assumes the near-perfect electric characteristics of the device. A comparison of the experimental data and optical modeling results indicated that the VNHA extracts the entire waveguide loss into the air. The EQE obtained in this study is the highest value obtained to date for bottom-emitting OLEDs.

| S-EPMC4346830 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data