Calibration and algorithm development for estimation of nitrogen in wheat crop using tractor mounted N-sensor.
Ontology highlight
ABSTRACT:
SUBMITTER: Singh M
PROVIDER: S-EPMC4354967 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:PURPOSE:Optical prospective motion correction substantially reduces sensitivity to motion in neuroimaging of human subjects. However, a major barrier to clinical deployment has been the time-consuming cross-calibration between the camera and MRI scanner reference frames. This work addresses this challenge. METHODS:A single camera was mounted onto the head coil for tracking head motion. Two new methods were developed: (1) a rapid calibration method for camera-to-scanner cross-calibration using a custom-made tool incorporating wireless active markers, and (2) a calibration adjustment method to compensate for table motion between scans. Both methods were tested at 1.5T and 3T in vivo. Simulations were performed to determine the required mechanical tolerance for repositioning of the camera. RESULTS:The rapid calibration method is completed in a short (<30 s) scan, which is carried out only once per installation. The calibration adjustment method requires no extra scan time and runs automatically whenever the system is used. The mechanical tolerance analysis indicates that most motion (90% reduction in voxel displacement) could be corrected even with far larger camera repositioning errors than are observed in practice. CONCLUSION:The methods presented here allow calibration of sufficient quality to be carried out and maintained with no additional technologist workload. Magn Reson Med 79:1911-1921, 2018. © 2017 International Society for Magnetic Resonance in Medicine.
| S-EPMC5899426 | biostudies-literature
Project description:Critical nitrogen (N) dilution curves (CNDCs) have been developed to describe the dilution dynamic of N and to diagnose N status in plants. In this study, to develop a convenient alternative CNDC determination method, four field experiments involving different N rates (0-360 kg N ha-1) and six wheat varieties were performed at different eco-sites from 2014 to 2019. The normalised difference red-edge (NDRE) index extracted from the RapidSCAN CS-45 (Holland Scientific Inc., Lincoln, NE, USA) sensor was used as a driving factor instead of plant dry matter (PDM) to establish a new alternative winter wheat CNDC. The newly developed CNDC was described by the equation Nc = 0.90NDRE-0.88, when NDRE values were ? 0.19 and constant Nc = 3.81%, which was independent of the NDRE values. Compared to PDM-derived CNDC (R2 = 0.73) developed with the same dataset, a comparable precision was obtained using NDRE-derived CNDC (R2 = 0.76) and both CNDCs could accurately discriminate wheat N status. Moreover, the NDRE could be inexpensively and rapidly measured using the active sensor. The relationship between NDRE-derived CNDC and grain yield was also analysed to facilitate in-season N management, and the R2 value reached 0.79 and 0.87 at jointing and booting stages, respectively. The NDRE-based CNDC can be used to effectively diagnose wheat N status and as an alternative approach for non-destructive determination of crop N levels.
| S-EPMC7146448 | biostudies-literature
Project description:In this article, we present a novel stochastic algorithm called simultaneous sensor calibration and deformation estimation (SCADE) to address the problem of modeling deformation behavior of a generic continuum manipulator (CM) in free and obstructed environments. In SCADE, using a novel mathematical formulation, we introduce a priori model-independent filtering algorithm to fuse the continuous and inaccurate measurements of an embedded sensor (e.g., magnetic or piezoelectric sensors) with an intermittent but accurate data of an external imaging system (e.g., optical trackers or cameras). The main motivation of this article is the crucial need of obtaining an accurate shape/position estimation of a CM utilized in a surgical intervention. In these robotic procedures, the CM is typically equipped with an embedded sensing unit (ESU) while an external imaging modality (e.g., ultrasound or a fluoroscopy machine) is also available in the surgical site. The results of two different set of prior experiments in free and obstructed environments were used to evaluate the efficacy of SCADE algorithm. The experiments were performed with a CM specifically designed for orthopaedic interventions equipped with an inaccurate Fiber Bragg Grating (FBG) ESU and overhead camera. The results demonstrated the successful performance of the SCADE algorithm in simultaneous estimation of unknown deformation behavior of the utilized unmodeled CM together with realizing the time-varying drift of the poor-calibrated FBG sensing unit. Moreover, the results showed the phenomenal out-performance of the SCADE algorithm in estimation of the CM's tip position as compared to FBG-based position estimations.
| S-EPMC7357879 | biostudies-literature
Project description:Forefoot load (FL) contributes to callus formation, which is one of the pathways to diabetic foot ulcers (DFU). In this study, we hypothesized that excessive FL, which cannot be detected by plantar load measurements within laboratory settings, occurs in daily walks. To demonstrate this, we created a FL estimation algorithm using foot motion data. Acceleration and angular velocity data were obtained from a motion sensor attached to each shoe of the subjects. The accuracy of the estimated FL was validated by correlation with the FL measured by force sensors on the metatarsal heads, which was assessed using the Pearson correlation coefficient. The mean of correlation coefficients of all the subjects was 0.63 at a level corridor, while it showed an intersubject difference at a slope and stairs. We conducted daily walk measurements in two diabetic patients, and additionally, we verified the safety of daily walk measurement using a wearable motion sensor attached to each shoe. We found that excessive FL occurred during their daily walks for approximately three hours in total, when any adverse event was not observed. This study indicated that FL evaluation method using wearable motion sensors was one of the promising ways to prevent DFUs.
| S-EPMC5559913 | biostudies-other
Project description:Chlorophyll meters are widely used to guide nitrogen (N) management by monitoring leaf N status in agricultural systems, but the effects of environmental factors and leaf characteristics on leaf N estimations are still unclear. In the present study, we estimated the relationships among SPAD readings, chlorophyll content and leaf N content per leaf area for seven species grown in multiple environments. There were similar relationships between SPAD readings and chlorophyll content per leaf area for the species groups, but the relationship between chlorophyll content and leaf N content per leaf area, and the relationship between SPAD readings and leaf N content per leaf area varied widely among the species groups. A significant impact of light-dependent chloroplast movement on SPAD readings was observed under low leaf N supplementation in both rice and soybean but not under high N supplementation. Furthermore, the allocation of leaf N to chlorophyll was strongly influenced by short-term changes in growth light. We demonstrate that the relationship between SPAD readings and leaf N content per leaf area is profoundly affected by environmental factors and leaf features of crop species, which should be accounted for when using a chlorophyll meter to guide N management in agricultural systems.
| S-EPMC4548214 | biostudies-other
Project description:Falls are one of the main concerns in the elderly population due to their high prevalence and associated consequences. Guidelines for the management of the elder with falls are comprised of multidimensional assessments, especially gait and balance. Daily clinical practice needs for timely, effortless, and precise tools to assess gait. This work presents the clinical validation of the G-STRIDE system, a 6-axis inertial measurement unit (IMU) with onboard processing algorithms, that allows the calculation of walking-related metrics correlated with clinical markers of fall risk. A cross-sectional case-control study was conducted with 163 participants (falls and non-falls groups). All volunteers were assessed with clinical scales and conducted a 15-min walking test at a self-selected pace while wearing the G-STRIDE. G-STRIDE is a low-cost solution to facilitate the transfer to society and clinical evaluations. It is open hardware and flexible and, thus, has the advantage of providing runtime data processing. Walking descriptors were derived from the device, and a correlation analysis was conducted between walking and clinical variables. G-STRIDE allowed measuring walking parameters in non-restricted walking conditions (e.g. hallway). Walking parameters statistically discriminate between falls and non-falls groups. We found good/excellent estimation accuracy (ICC = 0.885; [Formula: see text]) for walking speed, showing good/excellent correlation between gait speed and several clinical variables. G-STRIDE can calculate walking-related metrics that allow for discrimination between falls and non-falls groups, which correlates with clinical indicators of fall risk. A preliminary fall-risk assessment based on the walking parameters was found to improve the Timed Up and Go test in the identification of fallers.
| S-EPMC10244449 | biostudies-literature
Project description:Immersion in virtual environments is an important analog for scientists. Situations that cannot be safely organized in the real world are being simulated virtually to observe, evaluate, and train aspects of human behavior for psychology, therapy, and assessment. However, creating an immersive environment using traditional graphics practices may create conflict with a researcher's goal of evaluating user response to well-defined visual stimuli. Standard computer monitors may display color-accurate stimuli, but it is generally viewed from a seating position, where the participant can see real-world visual context. In this article, we propose a novel means to allow vision scientists to exert finer control over the participants visual stimuli and context. We propose and verify a device-agnostic approach to color calibration by analyzing display properties such as luminance, spectral distribution, and chromaticity. We evaluated five different head-mounted displays from different manufacturers and showed how our approach produces conforming visual outputs.
| S-EPMC10278547 | biostudies-literature
Project description:In this research, we focus on the use of Unmanned Aerial Vehicles (UAVs) for the delivery of payloads and navigation towards safe-landing zones, specifically on the modeling of flight dynamics of lightweight vehicles denoted Precision Aerial Delivery Systems (PADSs). While a wide range of nonlinear models has been developed and tested on high-end applications considering various degrees of freedom (DOF), linear models suitable for low-cost applications have not been explored thoroughly. In this study, we propose and compare two linear models, a linearized version of a 6-DOF model specifically developed for micro-lightweight systems, and an alternative model based on a double integrator. Both linear models are implemented with a sensor fusion algorithm using a Kalman filter to estimate the position and attitude of PADSs, and their performance is compared to a nonlinear 6-DOF model. Simulation results demonstrate that both models, when incorporated into a Kalman filter estimation scheme, can determine the flight dynamics of PADSs during smooth flights. While it is validated that the double integrator model can adequately operate under the proposed estimation scheme for up to small acceleration changes, the linearized model proves to be capable of reproducing the nonlinear model characteristics even during moderately steep turns.
| S-EPMC7570822 | biostudies-literature
Project description:The soft robot manipulator is attracting attention in the surgical fields with its intrinsic softness, lightness in its weight, and safety toward the human organ. However, it cannot be used widely because of its difficulty of control. To control a soft robot manipulator accurately, shape sensing is essential. This paper presents a method of estimating the shape of a soft robot manipulator by using a skin-type stretchable sensor composed of a multiwalled carbon nanotube (MWCNT) and silicone (p7670). The sensor can be easily fabricated and applied by simply attaching it to the surface of the soft manipulator. In its fabrication, MWCNT is sprayed on a teflon sheet, and liquid-state silicone is poured on it. After curing, we turn it over and cover it with another silicone layer. The sensor is fabricated with a sandwich structure to decrease the hysteresis of the sensor. After calibration and determining the relationship between the resistance of the sensor and the strain, three sensors are attached at 120° intervals. Using the obtained data, the curvature of the manipulator is calculated, and the entire shape is reconstructed. To validate its accuracy, the estimated shape is compared with the camera data. We experiment with three, six, and nine sensors attached, and the result of the error of shape estimation is compared. As a result, the minimum tip position error is approximately 8.9 mm, which corresponded to 4.45% of the total length of the manipulator when using nine sensors.
| S-EPMC9494719 | biostudies-literature
Project description:This paper presents a novel approach to predicting self-calibration in a pressure sensor using a proposed Levenberg Marquardt Back Propagation Artificial Neural Network (LMBP-ANN) model. The self-calibration algorithm should be able to fix major problems in the pressure sensor such as hysteresis, variation in gain and lack of linearity with high accuracy. The traditional calibration process for this kind of sensor is a time-consuming task because it is usually done through manual and repetitive identification. Furthermore, a traditional computational method is inadequate for solving the problem since it is extremely difficult to resolve the mathematical formula among multiple confounding pressure variables. Accordingly, this paper describes a new self-calibration methodology for nonlinear pressure sensors based on an LMBP-ANN model. The proposed method was achieved using a collected dataset from pressure sensors in real time. The load cell will be used as a reference for measuring the applied force. The proposed method was validated by comparing the output pressure of the trained network with the experimental target pressure (reference). This paper also shows that the proposed model exhibited a remarkable performance than traditional methods with a max mean square error of 0.17325 and an R-value over 0.99 for the total response of training, testing and validation. To verify the proposed model's capability to build a self-calibration algorithm, the model was tested using an untrained input data set. As a result, the proposed LMBP-ANN model for self-calibration purposes is able to successfully predict the desired pressure over time, even the uncertain behaviour of the pressure sensors due to its material creep. This means that the proposed model overcomes the problems of hysteresis, variation in gain and lack of linearity over time. In return, this can be used to enhance the durability of the grasping mechanism, leading to a more robust and secure grasp for paralyzed hands. Furthermore, the exposed analysis approach in this paper can be a useful methodology for the user to evaluate the performance of any measurement system in a real-time environment.
| S-EPMC6111596 | biostudies-literature