Controlling defects in graphene for optimizing the electrical properties of graphene nanodevices.
Ontology highlight
ABSTRACT:
SUBMITTER: Vicarelli L
PROVIDER: S-EPMC4415450 | biostudies-other | 2015 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:A simple method for fabricating single-layer graphene nanoribbons (sGNRs) from double-walled carbon nanotubes (DWNTs) was developed. A sonication treatment was employed to unzip the DWNTs by inducing defects in them through annealing at 500 °C. The unzipped DWNTs yielded double-layered GNRs (dGNRs). Further sonication allowed each dGNR to be unpeeled into two sGNRs. Purification performed using a high-speed centrifuge ensured that more than 99% of the formed GNRs were sGNRs. The changes induced in the electrical properties of the obtained sGNR by the absorption of nanoparticles of planar molecule, naphthalenediimide (NDI), were investigated. The shape of the I-V curve of the sGNRs varied with the number of NDI nanoparticles adsorbed. This was suggestive of the existence of a band gap at the narrow-necked part near the NDI-adsorbing area of the sGNRs.
| S-EPMC4513291 | biostudies-literature
Project description:The performance of devices and systems based on two-dimensional material systems depends critically on the quality of the contacts between 2D material and metal. A low contact resistance is an imperative requirement to consider graphene as a candidate material for electronic and optoelectronic devices. Unfortunately, measurements of contact resistance in the literature do not provide a consistent picture, due to limitations of current graphene technology, and to incomplete understanding of influencing factors. Here we show that the contact resistance is intrinsically dependent on graphene sheet resistance and on the chemistry of the graphene-metal interface. We present a physical model of the contacts based on ab-initio simulations and extensive experiments carried out on a large variety of samples with different graphene-metal contacts. Our model explains the spread in experimental results as due to uncontrolled graphene doping and suggests ways to engineer contact resistance. We also predict an achievable contact resistance of 30 Ω·μm for nickel electrodes, extremely promising for applications.
| S-EPMC5506027 | biostudies-literature
Project description:In recent years, graphene oxide has been considered as a soluble precursor of graphene for electronic applications. However, the performance lags behind that of graphene due to lattice defects. Here, the relation between the density of defects in the range of 0.2 % and 1.5 % and the transport properties is quantitatively studied. Therefore, the related flakes of monolayers of graphene were prepared from oxo-functionalized graphene (oxo-G). The morphologic structure of oxo-G was imaged by atomic force microscopy (AFM) and scanning tunneling microscopy (STM). Field-effect mobility values were determined to range between 0.3 cm2 V-1 s-1 and 33.2 cm2 V-1 s-1 , which were inversely proportional to the density of defects. These results provide the first quantitative description of the density of defects and transport properties, which plays an important role for potential applications.
| S-EPMC7317977 | biostudies-literature
Project description:Penta-graphene is a quasi-two-dimensional carbon allotrope consisting of a pentagonal lattice in which both sp2 and sp3-like carbons are present. Unlike graphene, penta-graphene exhibits a non-zero bandgap, which opens the possibility of its use in optoelectronic applications. However, as the observed bandgap is large, gap tuning strategies such as doping are required. In this work, density functional theory calculations are used to determine the effects of the different number of line defects of substitutional nitrogen or silicon atoms on the penta-graphene electronic behavior. Our results show that this doping can induce semiconductor, semimetallic, or metallic behavior depending on the doping atom and targeted hybridization (sp2 or sp3-like carbons). In particular, we observed that nitrogen doping of sp2-like carbons atoms can produce a bandgap modulation between semimetallic and semiconductor behavior. These results show that engineering line defects can be an effective way to tune penta-graphene electronic behavior.
| S-EPMC7229116 | biostudies-literature
Project description:We develop a simple method to fabricate the two-stacked graphene monolayers and investigate the electronic transport in such a system. The independence of the two graphene monolayers gives rise to the asymmetric resistance-gate voltage curves and an eight-fold degeneracy of Landau level. The position of the maximum resistance of the transfer curves shifts towards higher gate voltage with increasing magnetic field, which is attributed to the magnetic field induced interlayer decoupling of the stacked graphene monolayers.
| S-EPMC4033920 | biostudies-other
Project description:Dry-spinning method is extensively employed in fiber industry, comparing to the counter-part of wet-spinning process, it has advantages of environmentally friendly, high yield rate and no need for purification. Here, we report the synthesis of graphene oxide (GO) fibers via dry spinning GO inks with extremely high concentrations. The proper rheology properties of such GO inks allow us to dry spin GO fiber directly. Various dry spinning conditions are investigated, and the relationship between mechanical performance and micro-structure of the obtained GO fiber are established. We found that the existence of larger GO liquid crystal domains does not necessarily result to higher mechanical properties, and it is because those large GO liquid crystal domains evolve into thick GO films during drying process and thus prevent the intimate compaction of the whole GOF and leave behind gaps. This is detrimental for the mechanical properties, and thus the dry spin GOF are much weaker than that of wet spin ones. Importantly, Barus effects, that generally arise during the melt spinning of polymers, were not observed, indicating that caution must be taken when classical polymer rheology theories are applied to investigate the dynamic behaviors of GO solution.
| S-EPMC6050277 | biostudies-literature
Project description:Laser-induced graphene (LIG) on paper substrates is a desirable material for single-use point-of-care sensing with its high-quality electrical properties, low fabrication cost, and ease of disposal. While a prior study has shown how the repeated lasing of substrates enables the synthesis of high-quality porous graphitic films, however, the process-property correlation of lasing process on the surface microstructure and electrochemical behavior, including charge-transfer kinetics, is missing. The current study presents a systematic in-depth study on LIG synthesis to elucidate the complex relationship between the surface microstructure and the resulting electroanalytical properties. The observed improvements were then applied to develop high-quality LIG-based electrochemical biosensors for uric acid detection. We show that the optimal paper LIG produced via a dual pass (defocused followed by focused lasing) produces high-quality graphene in terms of crystallinity, sp2 content, and electrochemical surface area. The highest quality LIG electrodes achieved a high rate constant k0 of 1.5 × 10-2 cm s-1 and a significant reduction in charge-transfer resistance (818 Ω compared with 1320 Ω for a commercial glassy carbon electrode). By employing square wave anodic stripping voltammetry and chronoamperometry on a disposable two-electrode paper LIG-based device, the improved charge-transfer kinetics led to enhanced performance for sensing of uric acid with a sensitivity of 24.35 ± 1.55 μA μM-1 and a limit of detection of 41 nM. This study shows how high-quality, sensitive LIG electrodes can be integrated into electrochemical paper analytical devices.
| S-EPMC9284512 | biostudies-literature
Project description:In this study, the mechanical and thermal properties of graphene were systematically investigated using molecular dynamic simulations. The effects of temperature, strain rate and defect on the mechanical properties, including Young's modulus, fracture strength and fracture strain, were studied. The results indicate that the Young's modulus, fracture strength and fracture strain of graphene decreased with the increase of temperature, while the fracture strength of graphene along the zigzag direction was more sensitive to the strain rate than that along armchair direction by calculating the strain rate sensitive index. The mechanical properties were significantly reduced with the existence of defect, which was due to more cracks and local stress concentration points. Besides, the thermal conductivity of graphene followed a power law of λ~L0.28, and decreased monotonously with the increase of defect concentration. Compared with the pristine graphene, the thermal conductivity of defective graphene showed a low temperature-dependent behavior since the phonon scattering caused by defect dominated the thermal properties. In addition, the corresponding underlying mechanisms were analyzed by the stress distribution, fracture structure during the deformation and phonon vibration power spectrum.
| S-EPMC6474032 | biostudies-literature
Project description:The recent development of eumelanin pigment-based blends integrating "classical" organic conducting materials is expanding the scope of eumelanin in bioelectronics. Beyond the achievement of high conductivity level, another major goal lays in the knowledge and feasible control of structure/properties relationship. We systematically investigated different hybrid materials prepared by in situ polymerization of the eumelanin precursor 5,6-dihydroxyindole (DHI) in presence of various amounts of graphene-like layers. Spectroscopic studies performed by solid state nuclear magnetic resonance (ss-NMR), x-ray photoemission, and absorption spectroscopies gave a strong indication of the direct impact that the integration of graphene-like layers into the nascent polymerized DHI-based eumelanin has on the structural organization of the pigment itself, while infrared, and photoemission spectroscopies indicated the occurrence of negligible changes as concerns the chemical units. A tighter packing of the constituent units could represent a strong factor responsible for the observed improved electrical conductivity of the hybrid materials, and could be possible exploited as a tool for electrical conductivity tuning.
| S-EPMC6432792 | biostudies-literature
Project description:The reduction of CO2 emissions and its elimination from the atmosphere has become one of the major problems worldwide, since CO2 is the main cause of the greenhouse effect and climate change. In recent years, a great number of carbonaceous materials that can be used as CO2 adsorbents have been synthesized. The strategy is usually to synthesize the materials and determine their adsorption capacity without studying previously the factors that influence this capacity. In this work, different properties of the adsorbents are analyzed to study their influence on the CO2 adsorption capacity. For this purpose, 10 adsorbents have been synthesized using different strategies and characterized with X-ray photoelectron spectroscopy, X-ray diffraction, and micro-Raman spectroscopy. The percentage of sp2 carbons, the position of the D + D' peak of the second-order Raman spectrum, the micropore volume, and the grain size of the C sp2 domains have been related to the amount of CO2 adsorbed by the adsorbents. The results confirm a linear relationship between the volume of the micropores and the CO2 uptake and it proves that CO2 retention is favored in those materials that, in addition to having a high volume of micropores, also have low grain size of C.
| S-EPMC8796650 | biostudies-literature