The Rebirth of Waste Cooking Oil to Novel Bio-based Surfactants.
Ontology highlight
ABSTRACT:
SUBMITTER: Zhang QQ
PROVIDER: S-EPMC4421825 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Publications
The Rebirth of Waste Cooking Oil to Novel Bio-based Surfactants.
Zhang Qi-Qi QQ Cai Bang-Xin BX Xu Wen-Jie WJ Gang Hong-Ze HZ Liu Jin-Feng JF Yang Shi-Zhong SZ Mu Bo-Zhong BZ
Scientific reports 20150506
Waste cooking oil (WCO) is a kind of non-edible oil with enormous quantities and its unreasonable dispose may generate negative impact on human life and environment. However, WCO is certainly a renewable feedstock of bio-based materials. To get the rebirth of WCO, we have established a facile and high-yield method to convert WCO to bio-based zwitterionic surfactants with excellent surface and interfacial properties. The interfacial tension between crude oil and water could reach ultra-low value ...[more]
Similar Datasets
Project description:Solvent-free copolymerization of epoxides derived from fatty esters of waste cooking oil with phthalic anhydride using (salen)CrIIICl as catalyst and n-Bu₄NCl/DMAP (tetrabutylammonium chloride/4-(dimethylamino)pyridine) as co-catalysts was carried out for the first time under microwave irradiation, where reaction time was reduced from a number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3100-6750 g/mol) and dispersity values (D = 1.18-1.92) when (salen)CrIIICl/n-Bu₄NCl was used as catalysts. Moreover, in the case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5500-6950 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIIICl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (¹H-NMR) spectroscopy, gel permeation chromatography (GPC), thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) Techniques.
| S-EPMC5503379 | biostudies-literature
Project description:The world biodiesel production is increasing at a rapid rate. Despite its perceived safety for the environment, more detailed toxicity studies are mandatory, especially in the field of aquatic toxicology. While considerable attention has been paid to biodiesel combustion emissions, the toxicity of biodiesel in the aquatic environment has been poorly understood. In our study, we used an algae culture growth-inhibition test (OECD 201) for the comparison of the toxicity of B100 (pure biodiesel), produced by methanol transesterification of waste cooking oil (yellow grease), B0 (petroleum diesel fuel) and B20 (diesel-biodiesel blended of 20% biodiesel and 80% petroleum diesel fuel by volume). Two marine diatoms Attheya ussuriensis and Chaetoceros muelleri, the red algae Porphyridium purpureum and Raphidophyte Heterosigma akashiwo were employed as the aquatic test organisms. A sample of biodiesel from waste cooking oil without dilution with petroleum diesel (B100) showed the highest level of toxicity for the microalgae A. ussuriensis, C. muelleri and H. akashiwo, compared to hexane, methanol, petroleum diesel (B0) and diluted sample (B20). The acute EC50 in the growth-inhibition test (96 h exposure) of B100 for the four species was in the range of 3.75-23.95 g/L whereas the chronic toxicity EC50 (7d exposure) was in the range of 0.42-16.09 g/L.
| S-EPMC6317304 | biostudies-literature
Project description:Cooking oil waste leads to well-known environmental impacts and its bioremediation by lipase-based enzymatic activity can minimize the high cytotoxic potential. In addition, they are among the biocatalysts most commercialized worldwide due to the versatility of reactions and substrates. However, although lipases are able to process cooking oil wastes, the products generated from this process do not necessarily become less toxic. Thus, the aim of the current study is to analyze the bioremediation of lipase-catalyzed cooking oil wastes, as well as their effect on the cytotoxicity of both the oil and its waste before and after enzymatic treatment. Thus, assessed the post-frying modification in soybean oil and in its waste, which was caused by hydrolysis reaction catalyzed by commercial and home-made lipases. The presence of lipases in the extracts obtained from orange wastes was identified by zymography. The profile of the fatty acid esters formed after these reactions was detected and quantified through gas chromatography and fatty acids profile compared through multivariate statistical analyses. Finally, the soybean oil and its waste, with and without enzymatic treatment, were assessed for toxicity in cytotoxicity assays conducted in vitro using fibroblast cell culture. The soybean oil wastes treated with core and frit lipases through transesterification reaction were less toxic than the untreated oils, thus confirming that cooking oil wastes can be bioremediated using orange lipases.
| S-EPMC5657992 | biostudies-literature
Project description:Key challenges for the application of biodiesel include their high acid value, high viscosity, and low ester content. It is essential to develop later-generation biodiesel from unexploited non-food resources for a more sustainable future. Reuse of biowaste is critically important to address these issues of food safety and sustainability. Thus, the co-transesterification of waste cooking oil (WCO), algal oil (AO) and dimethyl carbonate (DMC) for the synthesis of fatty acid methyl esters (FAMEs) was investigated over a series of nanoparticle catalysts containing calcium, magnesium, potassium or nickel under mild reaction conditions. Nanoparticle catalyst samples were prepared from biowaste sources of chicken manure (CM), water hyacinth (WH) and algal bloom (AB), and characterized using XRD, Raman and FESEM techniques for the heterogeneous production of biodiesel. The catalyst was initially prepared by calcination at 850 °C for 4 h in a major presence of CaxMgyCO3, KCl and K2CO3. The WCO and AO co-conversion of 98% and FAMEs co-selectivity of 95% were obtained over CM nanoparticle catalyst under the reaction conditions of 80 °C, 20 mins and DMC to oil molar ratio of 6:1 with 3% catalyst loading and 3% methanol addition. Under the optimum condition, the density, viscosity, and cetane number of the biodiesel were in the range of diesel standards. Nanoparticle catalysts have been proven as a promising sustainable material in the catalytic transesterification of WCO and AO with the major presence of calcium, magnesium and potassium. This study highlights a sustainable approach via biowaste utilization for the enhancement of biodiesel quality with high ester content, low acid value, high cetane number, and low viscosity.
| S-EPMC7494454 | biostudies-literature
Project description:The influence of waste cooking oil (WCO) on the performance characteristics of asphaltic materials indigenous to Trinidad, namely, Trinidad Lake Asphalt (TLA), Trinidad Petroleum Bitumen (TPB), and TLA : TPB (50 : 50) blend, was investigated to deduce the applicability of the WCO as a performance enhancer for the base asphalt. The rheological properties of complex modulus (G (∗) ) and phase angle (δ) were measured for modified base asphalt blends containing up to 10% WCO. The results of rheology studies demonstrated that the incremental addition of WCO to the three parent binders resulted in incremental decreases in the rutting resistance (decrease in G (∗) /sinδ values) and increases in the fatigue cracking resistance (decrease in G (∗) sinδ value). The fatigue cracking resistance and rutting resistance for the TLA : TPB (50 : 50) blends were between those of the blends containing pure TLA and TPB. As operating temperature increased, an increase in the resistance to fatigue cracking and a decrease in the rutting resistance were observed for all of the WCO modified asphaltic blends. This study demonstrated the capability to create customized asphalt-WCO blends to suit special applications and highlights the potential for WCO to be used as an environmentally attractive option for improving the use of Trinidad asphaltic materials.
| S-EPMC4537772 | biostudies-other
Project description:Waste cooking oil (WCO), in many cases, can rejuvenate aged asphalt and restore its properties. However, the influence of WCO qualities on rejuvenation behaviors of aged asphalt has not been investigated in detail. The objective of this paper was to evaluate the effects of WCO viscosity and acid value on the basic, rheological, and chemical properties of a typical rejuvenated asphalt. Penetration, ring and ball (R and B) softening point, and ductility were tested to evaluate the influence of WCO qualities on basic properties of rejuvenated asphalts. Then, the rheological properties of rejuvenated asphalt were characterized based on rotational viscometer (RV), dynamic shear rheometer (DSR), and bending beam rheometer (BBR) test results. Further, SARA (saturates, aromatics, resins, and asphaltenes) fraction analysis and Fourier transform infrared spectroscopy (FTIR) tests were performed to investigate the effects of WCO qualities on asphalt chemical composition. Finally, grey correlation coefficients were calculated and the relationships between WCO qualities and rejuvenated asphalt properties were quantitatively evaluated. The experimental results indicated that WCO qualities influence the rejuvenation behaviors of aged asphalt significantly, and the WCO with higher qualities (low acid value and viscosity, as defined in this research) tends to achieve better rejuvenation effects. Based on the results of grey correlation analyses, the acid value is, relatively, a better indicator than viscosity in predicting the rejuvenation efficiency of WCO. The rejuvenation thresholds of WCO are varied with the categories of properties of rejuvenated asphalts, and WCO with an acid value of 0.4-0.7 mg KOH/g, or a viscosity of 140-540 mm²/s, can meet all of the performance requirements for asphalt rejuvenation used in this research.
| S-EPMC5459064 | biostudies-other
Project description:Background:Limonene is an important biologically active natural product widely used in the food, cosmetic, nutraceutical and pharmaceutical industries. However, the low abundance of limonene in plants renders their isolation from plant sources non-economically viable. Therefore, engineering microbes into microbial factories for producing limonene is fast becoming an attractive alternative approach that can overcome the aforementioned bottleneck to meet the needs of industries and make limonene production more sustainable and environmentally friendly. Results:In this proof-of-principle study, the oleaginous yeast Yarrowia lipolytica was successfully engineered to produce both d-limonene and l-limonene by introducing the heterologous d-limonene synthase from Citrus limon and l-limonene synthase from Mentha spicata, respectively. However, only 0.124 mg/L d-limonene and 0.126 mg/L l-limonene were produced. To improve the limonene production by the engineered yeast Y. lipolytica strain, ten genes involved in the mevalonate-dependent isoprenoid pathway were overexpressed individually to investigate their effects on limonene titer. Hydroxymethylglutaryl-CoA reductase (HMGR) was found to be the key rate-limiting enzyme in the mevalonate (MVA) pathway for the improving limonene synthesis in Y. lipolytica. Through the overexpression of HMGR gene, the titers of d-limonene and l-limonene were increased to 0.256 mg/L and 0.316 mg/L, respectively. Subsequently, the fermentation conditions were optimized to maximize limonene production by the engineered Y. lipolytica strains from glucose, and the final titers of d-limonene and l-limonene were improved to 2.369 mg/L and 2.471 mg/L, respectively. Furthermore, fed-batch fermentation of the engineered strains Po1g KdHR and Po1g KlHR was used to enhance limonene production in shake flasks and the titers achieved for d-limonene and l-limonene were 11.705 mg/L (0.443 mg/g) and 11.088 mg/L (0.385 mg/g), respectively. Finally, the potential of using waste cooking oil as a carbon source for limonene biosynthesis from the engineered Y. lipolytica strains was investigated. We showed that d-limonene and l-limonene were successfully produced at the respective titers of 2.514 mg/L and 2.723 mg/L under the optimal cultivation condition, where 70% of waste cooking oil was added as the carbon source, representing a 20-fold increase in limonene titer compared to that before strain and fermentation optimization. Conclusions:This study represents the first report on the development of a new and efficient process to convert waste cooking oil into d-limonene and l-limonene by exploiting metabolically engineered Y. lipolytica strains for fermentation. The results obtained in this study lay the foundation for more future applications of Y. lipolytica in converting waste cooking oil into various industrially valuable products.
| S-EPMC6781337 | biostudies-literature
Project description:The natural plant product bisabolene serves as a precursor for the production of a wide range of industrially relevant chemicals. However, the low abundance of bisabolene in plants renders its isolation from plant sources non-economically viable. Therefore, creation of microbial cell factories for bisabolene production supported by synthetic biology and metabolic engineering strategies presents a more competitive and environmentally sustainable method for industrial production of bisabolene. In this proof-of-principle study, for the first time, we engineered the oleaginous yeast Yarrowia lipolytica to produce α-bisabolene, β-bisabolene and γ-bisabolene through heterologous expression of the α-bisabolene synthase from Abies grandis, the β-bisabolene synthase gene from Zingiber officinale and the γ-bisabolene synthase gene from Helianthus annuus respectively. Subsequently, two metabolic engineering approaches, including overexpression of the endogenous mevalonate pathway genes and introduction of heterologous multidrug efflux transporters, were employed in order to improve bisabolene production. Furthermore, the fermentation conditions were optimized to maximize bisabolene production by the engineered Y. lipolytica strains from glucose. Finally, we explored the potential of the engineered Y. lipolytica strains for bisabolene production from the waste cooking oil. To our knowledge, this is the first report of bisabolene production in Y. lipolytica using metabolic engineering strategies. These findings provide valuable insights into the engineering of Y. lipolytica for a higher-level production of bisabolene and its utilization in converting waste cooking oil into various industrially valuable products.
| S-EPMC8601197 | biostudies-literature
Project description:The interest in using non-conventional yeasts to produce value-added compounds from low cost substrates, such as lignocellulosic materials, has increased in recent years. Setting out to discover novel microbial strains that can be used in biorefineries, an Issatchenkia orientalis strain was isolated from waste cooking oil (WCO) and its capability to produce ethanol from wheat straw hydrolysate (WSHL) was analyzed. As with previously isolated I. orientalis strains, WCO-isolated I. orientalis KJ27-7 is thermotolerant. It grows well at elevated temperatures up to 42 °C. Furthermore, spot drop tests showed that it is tolerant to various chemical fermentation inhibitors that are derived from the pre-treatment of lignocellulosic materials. I. orientalis KJ27-7 is particularly tolerant to acetic acid (up to 75 mM) and tolerates 10 mM formic acid, 5 mM furfural and 10 mM hydroxymethylfurfural. Important for biotechnological cellulosic ethanol production, I. orientalis KJ27-7 grows well on plates containing up to 10% ethanol and media containing up to 90% WSHL. As observed in shake flask fermentations, the specific ethanol productivity correlates with WSHL concentrations. In 90% WSHL media, I. orientalis KJ27-7 produced 10.3 g L-1 ethanol within 24 h. This corresponds to a product yield of 0.50 g g-1 glucose (97% of the theoretical maximum) and a volumetric productivity of 0.43 g L-1 h-1. Therefore, I. orientalis KJ27-7 is an efficient producer of lignocellulosic ethanol from WSHL.
| S-EPMC7915885 | biostudies-literature
Project description:There is a growing acceptance worldwide for the application of dispersants as a marine oil spill response strategy. The development of more effective dispersants with less toxicity and higher biodegradability would be a step forward in improving public acceptance and regulatory approvals for their use. By applying advances in environmental biotechnology, a bio-dispersant agent with a lipopeptide biosurfactant produced by Bacillus subtilis N3-1P as the key component was formulated in this study. The economic feasibility of producing biosurfactant (a high-added-value bioproduct) from fish waste-based peptone as a nutrient substrate was evaluated. Protein hydrolyzate was prepared from cod liver and head wastes obtained from fish processing facilities. Hydrolysis conditions (i.e., time, temperature, pH and enzyme to substrate level) for preparing protein hydrolyzates were optimized by response surface methodology using a factorial design. The critical micelle dilution (CMD) value for biosurfactant produced from the fish liver and head waste generated peptones was 54.72 and 47.59 CMD, respectively. Biosurfactant product generated by fish liver peptone had a low critical micelle concentration of 0.18 g L-1 and could reduce the surface tension of distilled water to 27.9 mN/m. Structure characterization proved that the generated biosurfactant product belongs to the lipopeptide class. An alternative to the key surfactant dioctyl sulfosuccinate sodium (DOSS) used in Corexit 9500 has been proposed based on a binary mixture of lipopeptides and DOSS that exhibited synergistic effects. Using the standard baffled flask test, a high dispersion efficiency of 76.8% for Alaska North Slope oil was achieved at a biodispersant composition of 80/20 (v/v) of lipopeptides/DOSS. The results show that fish waste can be utilized to produce a more effective, environmentally acceptable and cost-efficient biodispersant that can be applied to oil spills in the marine environment.
| S-EPMC7347989 | biostudies-literature