Low-energy Resistive Random Access Memory Devices with No Need for a Compliance Current.
Ontology highlight
ABSTRACT:
SUBMITTER: Xu Z
PROVIDER: S-EPMC4434835 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The intense development and study of resistive random access memory (RRAM) devices has opened a new era in semiconductor memory manufacturing. Resistive switching and carrier conduction inside RRAM films have become critical issues in recent years. Electron trapping/detrapping behavior is observed and investigated in the proposed contact resistive random access memory (CR-RAM) cell. Through the fitting of the space charge limiting current (SCLC) model, and analysis in terms of the random telegraph noise (RTN) model, the temperature-dependence of resistance levels and the high-temperature data retention behavior of the contact RRAM film are successfully and completely explained. Detail analyses of the electron capture and emission from the traps by forward and reverse read measurements provide further verifications for hopping conduction mechanism and current fluctuation discrepancies.
| S-EPMC3331868 | biostudies-other
Project description:Resistive random-access memory devices with atomic layer deposition HfO2 and radio frequency sputtering TiOx as resistive switching layers were fabricated successfully. Low-power characteristic with 1.52 μW set power (1 μA@1.52 V) and 1.12 μW reset power (1 μA@1.12 V) was obtained in the HfO2/TiOx resistive random-access memory (RRAM) devices by controlling the oxygen content of the TiOx layer. Besides, the influence of oxygen content during the TiOx sputtering process on the resistive switching properties would be discussed in detail. The investigations indicated that "soft breakdown" occurred easily during the electrical forming/set process in the HfO2/TiOx RRAM devices with high oxygen content of the TiOx layer, resulting in high resistive switching power. Low-power characteristic was obtained in HfO2/TiOx RRAM devices with appropriately high oxygen vacancy density of TiOx layer, suggesting that the appropriate oxygen vacancy density in the TiOx layer could avoid "soft breakdown" through the whole dielectric layers during forming/set process, thus limiting the current flowing through the RRAM device and decreasing operating power consumption.
| S-EPMC6509306 | biostudies-literature
Project description:In this study, we investigated the synaptic functions of TiN/Ti/TiO2/SiOx/Si resistive random access memory for a neuromorphic computing system that can act as a substitute for the von-Neumann computing architecture. To process the data efficiently, it is necessary to coordinate the information that needs to be processed with short-term memory. In neural networks, short-term memory can play the role of retaining the response on temporary spikes for information filtering. In this study, the proposed complementary metal-oxide-semiconductor (CMOS)-compatible synaptic device mimics the potentiation and depression with varying pulse conditions similar to biological synapses in the nervous system. Short-term memory dynamics are demonstrated through pulse modulation at a set pulse voltage of -3.5 V and pulse width of 10 ms and paired-pulsed facilitation. Moreover, spike-timing-dependent plasticity with the change in synaptic weight is performed by the time difference between the pre- and postsynaptic neurons. The SiOx layer as a tunnel barrier on a Si substrate provides highly nonlinear current-voltage (I-V) characteristics in a low-resistance state, which is suitable for high-density synapse arrays. The results herein presented confirm the viability of implementing a CMOS-compatible neuromorphic chip.
| S-EPMC7559005 | biostudies-literature
Project description:With the continuous scaling of resistive random access memory (RRAM) devices, in-depth understanding of the physical mechanism and the material issues, particularly by directly studying integrated cells, become more and more important to further improve the device performances. In this work, HfO2-based integrated 1-transistor-1-resistor (1T1R) RRAM devices were processed in a standard 0.25??m complementary-metal-oxide-semiconductor (CMOS) process line, using a batch atomic layer deposition (ALD) tool, which is particularly designed for mass production. We demonstrate a systematic study on TiN/Ti/HfO2/TiN/Si RRAM devices to correlate key material factors (nano-crystallites and carbon impurities) with the filament type resistive switching (RS) behaviours. The augmentation of the nano-crystallites density in the film increases the forming voltage of devices and its variation. Carbon residues in HfO2 films turn out to be an even more significant factor strongly impacting the RS behaviour. A relatively higher deposition temperature of 300?°C dramatically reduces the residual carbon concentration, thus leading to enhanced RS performances of devices, including lower power consumption, better endurance and higher reliability. Such thorough understanding on physical mechanism of RS and the correlation between material and device performances will facilitate the realization of high density and reliable embedded RRAM devices with low power consumption.
| S-EPMC4911574 | biostudies-literature
Project description:The optoelectronic resistive random-access memory (RRAM) with the integrated function of perception, storage and intrinsic randomness displays promising applications in the hardware level in-sensor image cryptography. In this work, 2D hexagonal boron nitride based optoelectronic RRAM is fabricated with semitransparent noble metal (Ag or Au) as top electrodes, which can simultaneous capture color image and generate physically unclonable function (PUF) key for in-sensor color image cryptography. Surface plasmons of noble metals enable the strong light absorption to realize an efficient modulation of filament growth at nanoscale. Resistive switching curves show that the optical stimuli can impede the filament aggregation and promote the filament annihilation, which originates from photothermal effects and photogenerated hot electrons in localized surface plasmon resonance of noble metals. By selecting noble metals, the optoelectronic RRAM array can respond to distinct wavelengths and mimic the biological dichromatic cone cells to perform the color perception. Due to the intrinsic and high-quality randomness, the optoelectronic RRAM can produce a PUF key in every exposure cycle, which can be applied in the reconfigurable cryptography. The findings demonstrate an effective strategy to build optoelectronic RRAM for in-sensor color image cryptography applications.
| S-EPMC11304321 | biostudies-literature
Project description:We report a new type of sustained and reversible unipolar resistive switching in a nanowire device made from a single strand of Cu:7,7,8,8-tetracyanoquinodimethane (Cu:TCNQ) nanowire (diameter <100 nm) that shows high ON/OFF ratio (~10(3)), low threshold voltage of switching (~3.5 V) and large cycling endurance (>10(3)). This indicates a promising material for high density resistive random access memory (ReRAM) device integration. Switching is observed in Cu:TCNQ single nanowire devices with two different electrode configuration: symmetric (C-Pt/Cu:TCNQ/C-Pt) and asymmetric (Cu/Cu:TCNQ/C-Pt), where contacts connecting the nanowire play an important role. This report also developed a method of separating out the electrode and material contributions in switching using metal-semiconductor-metal (MSM) device model along with a direct 4-probe resistivity measurement of the nanowire in the OFF as well as ON state. The device model was followed by a phenomenological model of current transport through the nanowire device which shows that lowering of potential barrier at the contacts likely occur due to formation of Cu filaments in the interface between nanowire and contact electrodes. We obtain quantitative agreement of numerically analyzed results with the experimental switching data.
| S-EPMC4887791 | biostudies-literature
Project description:The realization of ultra-low power Si-based resistive switching memory technology will be a milestone in the development of next generation non-volatile memory. Here we show that a high performance and ultra-low power resistive random access memory (RRAM) based on an Al/a-SiNx:H/p(+)-Si structure can be achieved by tuning the Si dangling bond conduction paths. We reveal the intrinsic relationship between the Si dangling bonds and the N/Si ratio x for the a-SiNx:H films, which ensures that the programming current can be reduced to less than 1 μA by increasing the value of x. Theoretically calculated current-voltage (I-V) curves combined with the temperature dependence of the I-V characteristics confirm that, for the low-resistance state (LRS), the Si dangling bond conduction paths obey the trap-assisted tunneling model. In the high-resistance state (HRS), conduction is dominated by either hopping or Poole-Frenkel (P-F) processes. Our introduction of hydrogen in the a-SiNx:H layer provides a new way to control the Si dangling bond conduction paths, and thus opens up a research field for ultra-low power Si-based RRAM.
| S-EPMC4623785 | biostudies-other
Project description:In an era of rapidly evolving artificial intelligence and 5G communications technologies, massive data storage and processing are required for the real-time operation of digital processors in conventional wearable devices. However, classical von-Neumann architecture computers are limited by bottleneck-related issues. As a solution, resistive random-access memory (RRAM) devices are being considered as next generation in-memory computing devices. Among various materials, a polydopamine (PDA) is an attractive candidate for the fabrication of wearable and flexible RRAM devices. Herein, an aluminum/PDA/aluminum structure is proposed to investigate the influence of the PDA layer on resistive switching. The resistance-switching characteristics of an Al/PDA/Al structure are investigated by changing the PDA's coating time and an on/off ratio of 2.48 × 103 is recorded. X-ray photoelectron spectroscopy reveals the presence of an Al2O3 layer in Al/PDA/Al structure, and the contents of oxygen vacancies are changed according to PDA coating time. Conductive filaments in the PDA/Al structure are confirmed by conductive atomic-force microscopy. As an application, a flexible Al/PDA/Al structure is fabricated using polyethylene terephthalate substrate and its operation is successfully confirmed. These results describe the resistive-switching characteristics, including oxygen vacancies, of Al/PDA/Al structures and provide new ways of understanding the resistive-switching mechanism of PDA-based RRAM devices.
| S-EPMC9332170 | biostudies-literature
Project description:The major hindrance for high-density application of two-terminal resistive random-access memory (RRAM) array design is unintentional sneak path leakage through adjacent cells. Herein, we propose a bilayer structure of Ta2O5/Al2O3-based bipolar type RRAM by evaluating the intrinsic nonlinear characteristics without integration with an additional transistor and selector device. We conducted X-ray photoelectron spectroscopy (XPS) analysis with different etching times to verify Ta2O5/Al2O3 layers deposited on the TiN bottom electrode. The optimized nonlinear properties with current suppression are obtained by varying Al2O3 thickness. The maximum nonlinearity (~71) is achieved in a Ta2O5/Al2O3 (3 nm) sample. Furthermore, we estimated the comparative read margin based on the I-V characteristics with different thicknesses of Al2O3 film for the crossbar array applications. We expect that this study about the effect of the Al2O3 tunnel barrier thickness on Ta2O5-based memristors could provide a guideline for developing a selector-less RRAM application.
| S-EPMC7560462 | biostudies-literature
Project description:Large device variation is a fundamental challenge for resistive random access memory (RRAM) array circuit. Improved device-to-device distributions of set and reset voltages in a SiNx RRAM device is realized via arsenic ion (As+) implantation. Besides, the As+-implanted SiNx RRAM device exhibits much tighter cycle-to-cycle distribution than the nonimplanted device. The As+-implanted SiNx device further exhibits excellent performance, which shows high stability and a large 1.73 × 103 resistance window at 85 °C retention for 104 s, and a large 103 resistance window after 105 cycles of the pulsed endurance test. The current-voltage characteristics of high- and low-resistance states were both analyzed as space-charge-limited conduction mechanism. From the simulated defect distribution in the SiNx layer, a microscopic model was established, and the formation and rupture of defect-conductive paths were proposed for the resistance switching behavior. Therefore, the reason for such high device performance can be attributed to the sufficient defects created by As+ implantation that leads to low forming and operation power.
| S-EPMC8226572 | biostudies-literature