Layer dependence and gas molecule absorption property in MoS2 Schottky diode with asymmetric metal contacts.
Ontology highlight
ABSTRACT:
SUBMITTER: Yoon HS
PROVIDER: S-EPMC4438430 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Two-dimensional (2D) molybdenum disulphide (MoS2) atomic layers have a strong potential to be used as 2D electronic sensor components. However, intrinsic synthesis challenges have made this task difficult. In addition, the detection mechanisms for gas molecules are not fully understood. Here, we report a high-performance gas sensor constructed using atomic-layered MoS2 synthesised by chemical vapour deposition (CVD). A highly sensitive and selective gas sensor based on the CVD-synthesised MoS2 was developed. In situ photoluminescence characterisation revealed the charge transfer mechanism between the gas molecules and MoS2, which was validated by theoretical calculations. First-principles density functional theory calculations indicated that NO2 and NH3 molecules have negative adsorption energies (i.e., the adsorption processes are exothermic). Thus, NO2 and NH3 molecules are likely to adsorb onto the surface of the MoS2. The in situ PL characterisation of the changes in the peaks corresponding to charged trions and neutral excitons via gas adsorption processes was used to elucidate the mechanisms of charge transfer between the MoS2 and the gas molecules.
| S-EPMC4307013 | biostudies-literature
Project description:MoS2 is a layered two-dimensional material with strong spin-orbit coupling and long spin lifetime, which is promising for electronic and spintronic applications. However, because of its large band gap and small electron affinity, a considerable Schottky barrier exists between MoS2 and contact metal, hindering the further study of spin transport and spin injection in MoS2. Although substantial progress has been made in improving device performance, the existence of metal-semiconductor Schottky barrier has not yet been fully understood. Here, we investigate permalloy (Py) contacts to both multilayer and monolayer MoS2. Ohmic contact is developed between multilayer MoS2 and Py electrodes with a negative Schottky barrier, which yields a high field-effect mobility exceeding 55 cm(2)V(-1)s(-1) at low temperature. Further, by applying back gate voltage and inserting different thickness of Al2O3 layer between the metal and monolayer MoS2, we have achieved a good tunability of the Schottky barrier height (down to zero). These results are important in improving the performance of MoS2 transistor devices; and it may pave the way to realize spin transport and spin injection in MoS2.
| S-EPMC4220285 | biostudies-literature
Project description:Physical and electronic asymmetry plays a crucial role in rectifiers and other devices with a directionally variant current-voltage (I-V) ratio. Several strategies for practically creating asymmetry in nanoscale components have been demonstrated, but complex fabrication procedures, high cost, and incomplete mechanistic understanding have significantly limited large-scale applications of these components. In this work, we present density functional theory calculations which demonstrate asymmetric electronic properties in a metal-semiconductor-metal (MSM) interface composed of stacked van der Waals (vdW) heterostructures. Janus MoSSe has an intrinsic dipole due to its asymmetric structure and, consequently, can act as either an n-type or p-type diode depending on the face at the interior of the stacked structure (SeMoS-SMoS vs. SMoSe-SMoS). In each configuration, vdW forces dominate the interfacial interactions, and thus, Fermi level pinning is largely suppressed. Our transport calculations show that not only does the intrinsic dipole cause asymmetric I-V characteristics in the MSM structure but also that different transmission mechanisms are involved across the S-S (direct tunneling) and S-Se interface (thermionic excitation). This work illustrates a simple and practical method to introduce asymmetric Schottky barriers into an MSM structure and provides a conceptual framework which can be extended to other 2D Janus semiconductors.
| S-EPMC7877374 | biostudies-literature
Project description:The design, fabrication, and characterization of ultra-high responsivity photodetectors based on mesoscopic multilayer MoS2 is presented, which is a less explored system compared to direct band gap monolayer MoS2 that has received increasing attention in recent years. The device architecture is comprised of a metal-semiconductor-metal (MSM) photodetector, where Mo was used as the contact metal to suspended MoS2 membranes. The photoresponsivity [Formula: see text] was measured to be ~1.4?×?104?A/W, which is?>?104 times higher compared to prior reports, while the detectivity D* was computed to be ~2.3?×?1011 Jones at 300?K at an optical power P of ~14.5?pW and wavelength ? of ~700?nm. In addition, the dominant photocurrent mechanism was determined to be the photoconductive effect (PCE), while a contribution from the photogating effect was also noted from trap-states that yielded a wide spectral photoresponse from UV-to-IR (400?nm to 1100?nm) with an external quantum efficiency (EQE) ~104. From time-resolved photocurrent measurements, a decay time ? d ~ 2.5 ms at 300?K was measured from the falling edge of the photogenerated waveform after irradiating the device with a stream of incoming ON/OFF white light pulses.
| S-EPMC5775306 | biostudies-literature
Project description:Recently, two-dimensional materials such as molybdenum disulphide (MoS2) have been demonstrated to realize field effect transistors (FET) with a large current on-off ratio. However, the carrier mobility in backgate MoS2 FET is rather low (typically 0.5-20 cm(2)/V · s). Here, we report a novel field-effect Schottky barrier transistors (FESBT) based on graphene-MoS2 heterojunction (GMH), where the characteristics of high mobility from graphene and high on-off ratio from MoS2 are properly balanced in the novel transistors. Large modulation on the device current (on/off ratio of 10(5)) is achieved by adjusting the backgate (through 300 nm SiO2) voltage to modulate the graphene-MoS2 Schottky barrier. Moreover, the field effective mobility of the FESBT is up to 58.7 cm(2)/V · s. Our theoretical analysis shows that if the thickness of oxide is further reduced, a subthreshold swing (SS) of 40 mV/decade can be maintained within three orders of drain current at room temperature. This provides an opportunity to overcome the limitation of 60 mV/decade for conventional CMOS devices. The FESBT implemented with a high on-off ratio, a relatively high mobility and a low subthreshold promises low-voltage and low-power applications for future electronics.
| S-EPMC4127518 | biostudies-literature
Project description:The p-n junction diode and field-effect transistor are the two most ubiquitous building blocks of modern electronics and optoelectronics. In recent years, the emergence of reduced dimensionality materials has suggested that these components can be scaled down to atomic thicknesses. Although high-performance field-effect devices have been achieved from monolayered materials and their heterostructures, a p-n heterojunction diode derived from ultrathin materials is notably absent and constrains the fabrication of complex electronic and optoelectronic circuits. Here we demonstrate a gate-tunable p-n heterojunction diode using semiconducting single-walled carbon nanotubes (SWCNTs) and single-layer molybdenum disulfide as p-type and n-type semiconductors, respectively. The vertical stacking of these two direct band gap semiconductors forms a heterojunction with electrical characteristics that can be tuned with an applied gate bias to achieve a wide range of charge transport behavior ranging from insulating to rectifying with forward-to-reverse bias current ratios exceeding 10(4). This heterojunction diode also responds strongly to optical irradiation with an external quantum efficiency of 25% and fast photoresponse <15 ?s. Because SWCNTs have a diverse range of electrical properties as a function of chirality and an increasing number of atomically thin 2D nanomaterials are being isolated, the gate-tunable p-n heterojunction concept presented here should be widely generalizable to realize diverse ultrathin, high-performance electronics and optoelectronics.
| S-EPMC3831469 | biostudies-literature
Project description:Graphene-semiconductor interface is important for the applications in electronic and optoelectronic devices. Here we report the modulation of the electric transport properties of graphene/ZnO nanowire Schottky diode by gate voltage (Vg). The ideality factor of the graphene/ZnO nanowire Schottky diode is ~1.7, and the Schottky barrier height is ~0.28 eV without external Vg. The Schottky barrier height is sensitive to Vg due to the variation of Fermi level of graphene. The barrier height increases quickly with sweeping Vg towards the negative value, while decreases slowly towards the positive Vg. Our results are helpful to understand the fundamental mechanism of the electric transport in graphene-semiconductor Schottky diode.
| S-EPMC4421871 | biostudies-other
Project description:We fabricated multi-layered graphene/MoS2 heterostructured devices by positioning mechanically exfoliated bulk graphite and single-crystalline 2H-MoS2 onto Au metal pads on a SiO2/Si substrate via a contamination-free dry transfer technique. We also studied the electrical transport properties of Au/MoS2 junction devices for systematic comparison. A previous work has demonstrated the existence of a positive Schottky barrier height (SBH) in the metal/MoS2 system. However, analysis of the SBH indicates that the contacts of the multi-layered graphene/MoS2 have tunable negative barriers in the range of 300 to -46 meV as a function of gate voltage. It is hypothesized that this tunable SBH is responsible for the modulation of the work function of the thick graphene in these devices. Despite the large number of graphene layers, it is possible to form ohmic contacts, which will provide new opportunities for the engineering of highly efficient contacts in flexible electronics and photonics.
| S-EPMC4558713 | biostudies-literature
Project description:The growing demand for sustained self-powered devices with multifunctional sensing networks is one of the main challenges for smart textiles, which are the critical elements for the future Internet of Things (IoT) and Point of Care (POC). Here, cellulose-based smart textile is integrated with dynamic Schottky diode (DSD) to generate sustained power source (current density of 8.9 mA m⁻2 ) for self-powered built-in sensing network. In response to normal and shear motions, a pressure sensor with a sensitivity of 0.12 KPa⁻1 and an impact sensor are demonstrated, respectively. The woven structure of the textile contributes to signal amplification, which can also form a matrix of sensing elements for distributed sensing. The proposed strategy of fabricating self-powered and multifunctional sensing networks with smart textiles shows tremendous potential for future intelligent society.
| S-EPMC10104626 | biostudies-literature
Project description:Transition from multi-layer to monolayer and sub-monolayer thickness leads to the many exotic properties and distinctive applications of two-dimensional (2D) MoS2. This transition requires atomic-layer-precision thinning of bulk MoS2 without damaging the remaining layers, which presently remains elusive. Here we report a soft, selective and high-throughput atomic-layer-precision etching of MoS2 in SF6 + N2 plasmas with low-energy (<0.4?eV) electrons and minimized ion-bombardment-related damage. Equal numbers of MoS2 layers are removed uniformly across domains with vastly different initial thickness, without affecting the underlying SiO2 substrate and the remaining MoS2 layers. The etching rates can be tuned to achieve complete MoS2 removal and any desired number of MoS2 layers including monolayer. Layer-dependent vibrational and photoluminescence spectra of the etched MoS2 are also demonstrated. This soft plasma etching technique is versatile, scalable, compatible with the semiconductor manufacturing processes, and may be applicable for a broader range of 2D materials and intended device applications.
| S-EPMC4728689 | biostudies-literature