Dataset Information

Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites.

ABSTRACT: High performance nanocomposites require well dispersion and high alignment of the nanometer-sized components, at a high mass or volume fraction as well. However, the road towards such composite structure is severely hindered due to the easy aggregation of these nanometer-sized components. Here we demonstrate a big step to approach the ideal composite structure for carbon nanotube (CNT) where all the CNTs were highly packed, aligned, and unaggregated, with the impregnated polymers acting as interfacial adhesions and mortars to build up the composite structure. The strategy was based on a bio-inspired aggregation control to limit the CNT aggregation to be sub 20-50 nm, a dimension determined by the CNT growth. After being stretched with full structural relaxation in a multi-step way, the CNT/polymer (bismaleimide) composite yielded super-high tensile strengths up to 6.27-6.94 GPa, more than 100% higher than those of carbon fiber/epoxy composites, and toughnesses up to 117-192 MPa. We anticipate that the present study can be generalized for developing multifunctional and smart nanocomposites where all the surfaces of nanometer-sized components can take part in shear transfer of mechanical, thermal, and electrical signals.

SUBMITTER: Han Y

PROVIDER: S-EPMC4476433 | biostudies-other | 2015

REPOSITORIES: biostudies-other

ACCESS DATA

Publications

Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites.

Han Yue Y Zhang Xiaohua X Yu Xueping X Zhao Jingna J Li Shan S Liu Feng F Gao Peng P Zhang Yongyi Y Zhao Tong T Li Qingwen Q

Scientific reports 20150622

High performance nanocomposites require well dispersion and high alignment of the nanometer-sized components, at a high mass or volume fraction as well. However, the road towards such composite structure is severely hindered due to the easy aggregation of these nanometer-sized components. Here we demonstrate a big step to approach the ideal composite structure for carbon nanotube (CNT) where all the CNTs were highly packed, aligned, and unaggregated, with the impregnated polymers acting as inter ...[more]

PMID: 26098627

Similar Datasets

Project description:Ceramic materials possessing the properties of high-strength and rigidity are widely used in industry. The shell nacre has a layered structure containing both macroscopic and microscopic levels and is equipped with superior qualities regarding hardness and strength. Therefore, the ceramic composites with a nacre-like layered structure have the potential to be utilized as sliding bearings employed in the harsh conditions of wells. For the purpose of this paper, a porous Al?O? ceramics skeleton with nanometer powder is prepared using the freeze-casting method. Then the porous ceramic skeleton is filled with polymer polymethyl methacrylate (PMMA) through mass polymerization to produce a bionic Al?O?/PMMA composite with a lamellar structure. The properties of the prepared composite are determined by the analysis of micro-hardness, fracture toughness, friction coefficient, wear scar diameter, and the morphology of the worn surface. Consequent results indicate that elevation in the A1?O? powder, which acts as the initial solid phase content, prompts the ceramic slurry to exhibit an increase in viscosity and a gradual decrease in the pore size of the ceramic skeleton. The prepared layered Al?O?/PMMA composite possesses high fracture toughness, which closely resembles that of Al, is approximately four times that of the matrix of the Al?O? ceramics and 16 times that of the PMMA. Three kinds of composites containing different solid phase content are subjected to testing involving lubrication by water-based drilling fluid to determine the friction coefficient of each. The results indicate that an increased load leads to a decreased friction coefficient while the impact of speed is not evident. Under dry conditions, the friction coefficient of three different composites tested, declines with elevated load and speed. With the use of water-based drilling fluid as lubrication, the wear scar diameter increases at higher speed, while dry conditions denote increased load. Abrasive wear is determined to be the principal form of erosion of layered Al?O?/PMMA composites.

Project description:The studies focusing on magnesium oxychloride cement (MOC) composites have recently become fairly widespread because of MOC's excellent mechanical properties and environmental sustainability. Numerous fillers, admixtures and nano-dopants were studied in order to improve the overall performance of MOC-based derivatives. Some of them exhibited specific flaws, such as a tendency to aggregate, increase in porosity, aeration of the composite matrix, depreciation in water resistance and mechanical strength, etc. In this manuscript, MOC-based composites doped by multi-walled carbon nanotubes (MWCNTs) are designed and tested. In order to modify the final properties of composites, diatomite was admixed as partial substitution of MgO, which was used in the composition of the researched material in excess, i.e., the majority of MgO constituted part of MOC and the rest served as fine filler. The composites were subjected to the broad experimental campaign that covered SEM (scanning electron microscopy), EDS (energy dispersive spectroscopy), HR-TEM (high-resolution transmission electron microscopy), XRD (X-ray diffraction), OM (optical microscopy) and STA-MS (simultaneous thermal analysis with mass spectroscopy). For 28 days hardened samples, macrostructural and microstructural parameters, mechanical properties, hygric and thermal characteristics were experimentally assessed. The incorporation of MWCNTs and diatomite resulted in the significant enhancement of composites' compactness, mechanical strength and stiffness and reduction in water absorption and rate of water imbibition. The thermal properties of the enriched MOC composites yielded interesting values and provided information for future modification of thermal performance of MOC composites with respect to their specific use in practice, e.g., in passive moderation of indoor climate. The combination of MWCNTs and diatomite represents a valuable modification of the MOC matrix and can be further exploited in the design and development of advanced building materials and components.

Dataset Information

Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites.

Publications

Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure