Vacuum-free transparent quantum dot light-emitting diodes with silver nanowire cathode.
Ontology highlight
ABSTRACT:
SUBMITTER: Jing P
PROVIDER: S-EPMC4510483 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:In this study, we report on the application of a dielectric/ultra-thin metal/dielectric (DMD) multilayer consisting of ytterbium (Yb)-doped molybdenum oxide (MoO3)/silver (Ag)/MoO3 stacked as the transparent cathode in top-emitting green quantum dot light-emitting diodes (QLED). By optimizing the Yb doping ratio, we have highly improved the electron injection ability from 0.01 to 0.35. In addition, the dielectric/ultra-thin metal/dielectric (DMD) cathode also shows a low sheet resistance of only 12.2 ?/sq, which is superior to the resistance of the commercially-available indium tin oxide (ITO) electrode (~15 ?/sq). The DMD multilayer exhibits a maximum transmittance of 75% and an average transmittance of 70% over the visible range of 400-700 nm. The optimized DMD-based G-QLED has a smaller current leakage at low driving voltage. The optimized DMD-based G-QLED enhances the current density than that of G-QLED with indium zinc oxide (IZO) as a cathode. The fabricated DMD-based G-QLED shows a low turn-on voltage of 2.2 V, a high current efficiency of 38 cd/A, and external quantum efficiency of 9.8. These findings support the fabricated DMD multilayer as a promising cathode for transparent top-emitting diodes.
| S-EPMC7221779 | biostudies-literature
Project description:Silver nanowires (AgNWs) have been successfully demonstrated to function as next-generation transparent conductive electrodes (TCEs) in organic semiconductor devices owing to their figures of merit, including high optical transmittance, low sheet resistance, flexibility, and low-cost processing. In this article, high-quality, solution-processed AgNWs with an excellent optical transmittance of 96.5% at 450 nm and a low sheet resistance of 11.7 Ω/sq were demonstrated as TCEs in inorganic III-nitride LEDs. The transmission line model applied to the AgNW contact to p-GaN showed that near ohmic contact with a specific contact resistance of ~10(-3) Ωcm(2) was obtained. The contact resistance had a strong bias-voltage (or current-density) dependence: namely, field-enhanced ohmic contact. LEDs fabricated with AgNW electrodes exhibited a 56% reduction in series resistance, 56.5% brighter output power, a 67.5% reduction in efficiency droop, and a approximately 30% longer current spreading length compared to LEDs fabricated with reference TCEs. In addition to the cost reduction, the observed improvements in device performance suggest that the AgNWs are promising for application as next-generation TCEs, to realise brighter, larger-area, cost-competitive inorganic III-nitride light emitters.
| S-EPMC4558582 | biostudies-literature
Project description:Solution-processed silver nanowire (AgNW) has been considered as a promising material for next-generation flexible transparent conductive electrodes. However, despite the advantages of AgNWs, some of their intrinsic drawbacks, such as large surface roughness and poor interconnection between wires, limit their practical application in organic light-emitting diodes (OLEDs). Herein, we report a high-performance AgNW-based hybrid electrode composed of indium-doped zinc oxide (IZO) and poly (3,4-ethylenediowythiophene):poly(styrenesulfonate) [PEDOT:PSS]. The IZO layer protects the underlying AgNWs from oxidation and corrosion and tightly fuses the wires together and to the substrate. The PEDOT:PSS effectively reduces surface roughness and increases the hybrid films' transmittance. The fabricated electrodes exhibited a low sheet resistance of 5.9 Ωsq-1 with high transmittance of 86% at 550 nm. The optical, electrical, and mechanical properties of the AgNW-based hybrid films were investigated in detail to determine the structure-property relations, and whether optical or electrical properties could be controlled with variation in each layer's thickness to satisfy different requirements for different applications. Flexible OLEDs (f-OLEDs) were successfully fabricated on the hybrid electrodes to prove their applicability; their performance was even better than those on commercial indium doped tin oxide (ITO) electrodes.
| S-EPMC5050450 | biostudies-literature
Project description:Improving the light extraction efficiency by introducing optical-functional structures outside of quantum dot light emitting diodes (QLEDs) for further enhancing the external quantum efficiency (EQE) is essential for their application in display and lighting industries. Although the efficiency of QLEDs has been optimized by controlling the synthesis of the quantum dots, the low outcoupling efficiency is indeed unresolved because of total internal reflections, waveguides and metal surface absorptions within the device. Here, we utilize multiscale nanostructures attached to the outer surface of the glass substrate to extract the trapped light from the emitting layers of QLEDs. The result indicates that both the EQE and luminance are improved from 12.29% to 17.94% and 122 400 cd m-2 to 178 700 cd m-2, respectively. The maximum EQE and current efficiency improve to 21.3% and 88.3 cd A-1, respectively, which are the best performances among reported green QLEDs with light outcoupling nanostructures. The improved performance is ascribed to the elimination of total internal reflection by multiscale nanostructures attached to the outer surface of the QLEDs. Additionally, the simulation results of the finite-difference time domain (FDTD) also demonstrate that the light trapping effect is reduced by the multiscale nanostructures. The design of novel light outcoupling nanostructures for further improving the efficiency of QLEDs can promote their application in display and lighting industries.
| S-EPMC9417338 | biostudies-literature
Project description:Recently, freestanding polymer thin films encapsulated with nanostructures have attracted the significant attention of the scientific community due to their promising application in portable optoelectronic devices. In this research contribution, we have fabricated a freestanding polymer thin film of poly(vinyl alcohol) (PVA) encapsulated with carbon nitride quantum dots (CN-QDs) using the casting method, for the first time. The PVA polymer matrix provides mechanical support as well as dispersion of the CN-QDs preventing its solid-state quenching. From UV-visible spectra, it is revealed that optical transparency decreases with an increase in the concentration of CN-QDs within the PVA polymeric thin film. Such kind of decrease in optical transparency is one of the crucial factors for the optical concert of a nanomaterial. Interestingly, we have optimized the synthesis protocol to retain 40% transparency of the thin film by incorporating 10 wt % CN-QDs along with PVA without deteriorating its optical behavior. It is observed that when CN-QDs are embedded in the PVA matrix, emission becomes independent of excitation wavelength and is localized in the 510-530 nm region of the spectrum. Thus, the films exhibit excellent greenish-yellow emission when excited at 420 nm with the Commission Internationale de l'èclairage (CIE) coordinates (0.39, 0.46) and a correlated color temperature (CCT) of 4105 K. These excellent optoelectronic properties make them a promising candidate for practical phosphor applications. In a nutshell, this study demonstrates a promising way to exhibit the luminescence potential of freestanding polymer/CN-QD films in CN-QD-based solid-state lighting systems.
| S-EPMC8427780 | biostudies-literature
Project description:The phenomenon of positive aging, i.e., efficiency increased with time, is observed in quantum-dot light-emitting diodes (QLEDs). For example, the external quantum efficiency (EQE) of blue QLEDs is significantly improved from 4.93% to 12.97% after storage for 8 d. The origin of such positive aging is thoroughly investigated. The finding indicates that the interfacial reaction between Al cathode and ZnMgO electron transport layer accounts for such improvement. During shelf-aging, the Al slowly reacts with the oxygen from ZnMgO, and consequently, leads to the formation of AlO x and the production of oxygen vacancies in ZnMgO. The AlO x interlayer reduces the electron injection barrier while the oxygen vacancies increase the conductivity of ZnMgO and, as a result, the electron injection is effectively enhanced. Moreover, the AlO x can effectively suppress the quenching of excitons by metal electrode. Due to the enhancement of electron injection and suppression of exciton quenching, the aged blue, green, and red QLEDs exhibit a 2.6-, 1.3-, and 1.25-fold efficiency improvement, respectively. The studies disclose the origin of positive aging and provide a new insight into the exciton quenching mechanisms, which would be useful for further constructing efficient QLED devices.
| S-EPMC6193172 | biostudies-literature
Project description:The operating lifetime of blue quantum-dot light-emitting diodes (QLED) is currently a short slab for this emerging display technology. To pinpoint the origin of device degradation, here we apply multiple techniques to monitor the electric-field distribution and space-charge accumulation across the multilayered structure before and after lifetime tests. Evident by charge-modulated electro-absorption and capacitance-voltage characteristics, the excited electrons in blue quantum dots (QD) are prone to cross the type II junction between the QD emission layer and the electron-transporting layer (ETL) due to the offset of conduction band minimum, leading to space-charge accumulation and operating-voltage rise in the ETL. Therefore, unlike those very stable red devices, of which the lifetime is primarily limited by the slow degradation of hole-transporting layer, the poor lifetime of blue QLED originates from the fast degradation at the QD-ETL junction. Materials engineering for efficient electron injection is prerequisite for the boost of operating lifetime.
| S-EPMC6377672 | biostudies-literature
Project description:Optimization of ink-jet printing conditions of quantum-dot (QD) ink by cosolvent process and improvement of quantum-dot light-emitting diodes (QLEDs) characteristics assisted by vacuum annealing were analyzed in this research. A cosolvent process of hexane and ortho-dichlorobenzene (oDCB) was optimized at the ratio of 1:2, and ink-jetting properties were analyzed using the Ohnesorge number based on the parameters of viscosity and surface tension. However, we found that these cosolvents systems cause an increase in the boiling point and a decrease in the vapor pressure, which influence the annealing characteristics of the QD emission layer (EML). Therefore, we investigated QLEDs' performance depending on the annealing condition for ink-jet printed QD EML prepared using cosolvents systems of hexane and oDCB. We enhanced the quality of QD EML and device performance of QLEDs by a vacuum annealing process, which was used to prevent exposure to moisture and oxygen and to promote effective evaporation of solvent in QD EML. As a result, the characteristics of QLEDs formed using ink-jet printed QD EML annealed under vacuum environment increased luminescence (L), current efficiency (CE), external quantum efficiency (EQE), and lifetime (LT50) by 30.51%, 33.7%, 21.70%, and 181.97%, respectively, compared to QLEDs annealed under air environment.
| S-EPMC7660697 | biostudies-literature
Project description:Up-conversion electroluminescence, in which the energy of a emitted photon is higher than that of the excitation electron, is observed in quantum-dot light-emitting diodes. Here, we study its mechanism by investigating the effect of thermal energy on the charge injection dynamic. Based on the results of temperature-dependent electroluminescence and theoretical analysis, we reveal that at sub-bandgap voltage, holes can be successfully injected into quantum-dots via thermal-assisted thermionic-emission mechanism, thereby enabling the sub-bandgap turn-on and up-conversion electroluminescence of the devices. Further theoretical deduction and experimental results confirm that thermal-assisted hole-injection is the universal mechanism responsible for the up-conversion electroluminescence. This work uncovers the charge injection process and unlocks the sub-bandgap turn-on mechanism, which paves the road for the development of up-conversion devices with power conversion efficiency over 100%.
| S-EPMC8766545 | biostudies-literature
Project description:This paper reports a highly reliable transparent conductive electrode (TCE) that integrates silver nanowires (AgNWs) and high-quality graphene as a protecting layer. Graphene with minimized defects and large graphene domains has been successfully obtained through a facile two-step growth approach. Ultraviolet light emitting diodes (UV-LEDs) were fabricated with AgNWs or hybrid electrodes where AgNWs were combined with two-step grown graphene (A-2GE) or conventional one-step grown graphene (A-1GE). The device performance and reliability of the UV-LEDs with three different electrodes were compared. The A-2GE offered high figure of merit owing to the excellent UV transmittance and reduced sheet resistance. As a consequence, the UV-LEDs made with A-2GE demonstrated reduced forward voltage, enhanced electroluminescence (EL) intensity, and alleviated efficiency droop. The effects of joule heating and UV light illumination on the electrode stability were also studied. The present findings prove superior performance of the A-2GE under high current injection and continuous operation of UV LED, compared to other electrodes. From our observation, the A-2GE would be a reliable TCE for high power UV-LEDs.
| S-EPMC4937441 | biostudies-other