Microwave axial dielectric properties of carbon fiber.
Ontology highlight
ABSTRACT:
SUBMITTER: Hong W
PROVIDER: S-EPMC4609955 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The microwave absorption properties of chromite and the feasibility of microwave reduction chromite have been discussed. The results show that as the density increases, the dielectric properties of materials increase. The dielectric properties are the best (the value around 4.2) when the silica ratio is 0.5. Microwave penetration depth shows that chromite and the mixture have good wave absorption properties.
| S-EPMC7288365 | biostudies-literature
Project description:In this paper, the oil-in-gelatin based tissue-mimicking materials (TMMs) doped with carbon based materials including carbon nanotube, graphene ink or lignin were prepared. The volume percent for gelatin based mixtures and oil based mixtures were both around 50%, and the doping amounts were 2 wt %, 4 wt %, and 6 wt %. The effect of doping material and amount on the microwave dielectric properties including dielectric constant and conductivity were investigated over an ultra-wide frequency range from 2 GHz to 20 GHz. The coaxial open-ended reflection technology was used to evaluate the microwave dielectric properties. Six measured values in different locations of each sample were averaged and the standard deviations of all the measured dielectric properties, including dielectric constant and conductivity, were less than one, indicating a good uniformity of the prepared samples. Without doping, the dielectric constant was equal to 23 ± 2 approximately. Results showed with doping of carbon based materials that the dielectric constant and conductivity both increased about 5% to 20%, and the increment was dependent on the doping amount. By proper selection of doping amount of the carbon based materials, the prepared material could map the required dielectric properties of special tissues. The proposed materials were suitable for the phantom used in the microwave medical imaging system.
| S-EPMC5456944 | biostudies-other
Project description:Dielectric properties study is important in understanding the interaction between materials within electromagnetic field. By knowing and understanding the dielectric properties of materials, an efficient and effective microwave heating process and products can be designed. In this study, the dielectric properties of several encapsulation wall materials were measured using open-ended coaxial probe method. This method was selected due to its simplicity and high accuracy. All materials exhibited similar behavior. The result inferred that ?-cyclodextrin (BC), starch (S), Arabic (GA) and maltodextrin (M) with various dextrose equivalent exhibited effective encapsulation wall materials in microwave encapsulation-drying technique owing to loss tangent values which were higher than 0.1 at general application frequency of 2.45 GHz. Thus, these were found to be suitable as wall material to encapsulate the selected core material in this microwave encapsulation-drying method. On contrary, sodium caseinate showed an ineffective wall material to be used in microwave encapsulation-drying. The differences in the values of dielectric constant, loss factor and loss tangent were found to be contributed by frequency, composition and bulk density.
| S-EPMC6233465 | biostudies-literature
Project description:The GABA molecule is the major inhibitory neurotransmitter in the mammalian central nervous system. Through binding to post-synaptic neurons, GABA reduces the neuronal excitability by hyperpolarization. Correct binding between the GABA molecules and its receptors relies on molecular recognition. Earlier studies suggest that recognition is determined by the geometries of the molecule and its receptor. We employed dielectric relaxation spectroscopy (DRS) to study the conformation and dielectric properties of the GABA molecule under physiologically relevant laboratory conditions. The dielectric properties of GABA investigated have given us new insights about the GABA molecule, such as how they interact with each other and with water molecules at different temperatures (22°C and 37.5°C). Higher temperature leads to lower viscosity, thus lower relaxation time. The change in the GABA relaxation time due to concentration change is more associated with the solution viscosity than with the GABA dipole moment. A resonance behavior was observed with high GABA concentrations at physiological temperature, where there might be a phase transition at a certain temperature for a given GABA concentration that leads to a sudden change of the dielectric properties.
| S-EPMC8433407 | biostudies-literature
Project description:Phase engineering is an important strategy to modulate the electronic structure of molybdenum disulfide (MoS2). MoS2-based composites are usually used for the electromagnetic wave (EMW) absorber, but the effect of different phases on the EMW absorbing performance, such as 1T and 2H phase, is still not studied. In this work, micro-1T/2H MoS2 is achieved via a facile one-step hydrothermal route, in which the 1T phase is induced by the intercalation of guest molecules and ions. The EMW absorption mechanism of single MoS2 is revealed by presenting a comparative study between 1T/2H MoS2 and 2H MoS2. As a result, 1T/2H MoS2 with the matrix loading of 15% exhibits excellent microwave absorption property than 2H MoS2. Furthermore, taking the advantage of 1T/2H MoS2, a flexible EMW absorbers that ultrathin 1T/2H MoS2 grown on the carbon fiber also performs outstanding performance only with the matrix loading of 5%. This work offers necessary reference to improve microwave absorption performance by phase engineering and design a new type of flexible electromagnetic wave absorption material to apply for the portable microwave absorption electronic devices.
| S-EPMC8079512 | biostudies-literature
Project description:This work presents lightweight epoxy foams loaded with very low weight percentages (≤0.5 wt.%) of carbon fibers (CFs) with different lengths (3 mm, 6 mm, and 12 mm) as broadband microwave absorbing materials for anechoic chamber application. The effect of CF length on microwave absorption, especially on the absorption frequency band, is investigated for frequencies between 1 and 15 GHz. For the elaboration of composites, three different methods-spatula, shear mixing, and ultrasounds-are used for the dispersion of CFs. The observation of these CFs, after the dispersion step, shows a high fiber breakage rate when shear mixing is used, unlike when spatula or ultrasounds methods are used. On the other hand, the characterization of the elaborated composites highlights a correlation between the mixing methods, hence the fiber brakeage, and the measured reflection coefficient (reflection loss) of the composites. As a result, the minimum value of the reflection coefficient is shifted toward the high frequencies when the fiber breakage is observed, suggesting that short CFs absorb at high frequencies while long CFs absorb at low frequencies. Dielectric properties, extracted from the measurement in free space, of composites elaborated with different fiber lengths (3 mm, 6 mm, and 12 mm) confirm that short CFs (3 mm) show maximum losses at high frequencies (around 15 GHz) while long CFs (12 mm) show maximum dielectric losses at low frequencies (below 4 GHz). However, no significant variation is observed on the real part of the relative permittivity, as a function of fiber length, for these porous composites loaded with very low CF rates. A hybrid composite, with a mix of different CF lengths, is prepared and characterized. The simulation of the absorption performance of a pyramidal absorber, based on this hybrid composite, is compared to the one of pyramidal absorber based on composites loaded with a single length of carbon fibers. The pyramidal absorber-based hybrid composite predicts the best absorption performance, especially at the low frequency band. The simulated reflection coefficient of this absorber is less than -12 dB in all the studied frequency range, and less than -40 dB for frequencies higher than 3 GHz. This result confirms the interest of using a mix of carbon fiber lengths to achieve a broadband microwave absorber.
| S-EPMC7762112 | biostudies-literature
Project description:This study discusses the production of microwave baked gluten-free cakes formulated by mixing buckwheat flour and rice flour at different concentrations. Three different ratios of buckwheat flour to rice flour (20:80%, 30:70%, 40:60%) and two different gum types (xanthan and guar gum) with a white layer cake recipe were employed. The batters were baked in microwave oven at different microwave powers (540 W, 450 W, 360 W) for different baking times (3 min, 3.5 min, 4 min). The effect of microwave power, baking time and buckwheat flour concentration on weight loss, color, specific volume, porosity, total phenolic content and dielectric properties were investigated. The optimum microwave power, baking time and buckwheat flour concentration were found as 432.77 W, 3 min, 40% for guar gum added cakes and 360 W, 3.70 min and 29.23% for xanthan gum added ones. It was found that weight loss and color values of the cakes that were baked at the optimal conditions were less than those of control cakes. On the other hand, total phenolic content, specific volume, porosity, dielectric constant and dielectric loss factor values were higher for guar gum added cakes compared to control samples. In addition, it was observed that the cakes prepared with guar gum had similar pore size distribution with control cakes. As a conclusion of the study, it can be declared that surface color and specific volume problems of microwave baking could be solved by addition of guar gum to the formulation which also enables the production of functional, phenolic rich microwave baked cakes.
| S-EPMC6423201 | biostudies-literature
Project description:Carbon-based composites have been proven to be strong candidates for microwave absorbers in recent years. However, as an important member, magnetic hard carbon (HC)-based composites have rarely been studied in the field of microwave absorption. In this study, HC embedded with FeSiAl (FeSiAl@HC) was synthesized by pyrolyzing a mixture of FeSiAl flakes and phenolic resin (PR). The as-synthesized HC-FeSiAl exhibited a layered structure, and the detailed microstructures were modified by changing the mass ratio of FeSiAl flakes and PR. Thus, the as-synthesized HC-FeSiAl exhibited tunable magnetic properties, wealthy functional groups, excellent thermal stability, and enhanced microwave absorption properties. The optimal minimum reflection loss is lower up to -36.1 dB, and the effective absorption bandwidth is wider up to 11.7 GHz. These results indicated that HC-FeSiAl should be a strong candidate for practical applications of microwave absorption, which may provide new insight into the synthesis of magnetic HC-based composites.
| S-EPMC9457624 | biostudies-literature
Project description:Polymer composites with electrically conductive inclusions are intensively developed for microwave shielding applications, where lightweight and elastic coatings are necessary. In this paper, dielectric properties of hybrid polyethylene composites containing cobalt nanoparticles and multi-wall carbon nanotubes (MWCNT) were investigated in the wide frequency range of 20-40 GHz for electromagnetic shielding applications. The percolation threshold in the hybrid system is close to 6.95 wt% MWCNT and 0.56 Co wt%. Cobalt nanoparticles (up to highest investigated concentration 4.8 wt%) had no impact on the percolation threshold, and for the fixed total concentration of fillers, the complex dielectric permittivity is higher for composites with bigger MWCNT concentrations. Moreover, the microwave complex dielectric permittivity of composites with high concentration of fillers is quite high (for composites with 13.4 wt% MWCNT and 1.1 wt% Co ε' ≈ ε″ ≈ 20 at 30 GHz, it corresponds to microwave absorption 50% of 1 mm thickness plate); therefore, these composites are suitable for electromagnetic shielding applications.
| S-EPMC8912063 | biostudies-literature
Project description:Myocardium is an excitable tissue with electrical conductivity and mechanical strength. In this work, carbon fibers (CFs) and co-axial fibrous mesh were integrated which combined the high modulus and excellent electrical conductivity of CFs and the fibrous and porous structures of the electrospun fibers. The scaffold was fabricated by simply integrating coaxial electrospun fibers and carbon fibers through a freeze-drying procedure. It was shown that the integration of carbon fibers have the conductivity and Young's modulus of the fibrous mesh increased significantly, meanwhile, upregulated the expression of CX43, α-actinin, RhoA of the neonatal rat primary cardiomyocytes and primary human umbilical vein endothelial cells (HUVECs), and promoted the secretion of VEGF of HUVECs. Moreover, the cardiomyocytes grown on the scaffolds increased the ability of HUVECs migration. When implanted to the injury area post myocardial infraction, the scaffolds were able to effectively enhance the tissue regeneration and new vessel formation, which rescued the heart dysfunction induced by the myocardial infraction, evidenced by the results of echocardiography and histochemical analysis. In conclusion, the composite scaffolds could promote the myocardium regeneration and function's recovery by enhancing cardiomyocytes maturation and angiogenesis and establishing the crosstalk between the cardiomyocytes and the vascular endothelial cells.
| S-EPMC9465342 | biostudies-literature