Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Porous VO(x)N(y) nanoribbons supported on CNTs as efficient and stable non-noble electrocatalysts for the oxygen reduction reaction.

ABSTRACT: Novel nanocomposites of carbon nanotubes supported porous VO(x)N(y) nonoribbons (VO(x)N(y)-CNTs) have been synthesized by the annealing of the sol-gel mixture of CNTs and V2O5 under NH3 atmosphere as well as the ageing process in air. Besides the morphological and structural characterizations revealed by TEM, SEAD, EDS, XRD and XPS measurements, typical electrochemical tests including cyclic voltammetry (CV), rotating disk electrode (RDE) and chronoamperometry have been employed to determine the oxygen reduction reaction (ORR) performance of VO(x)N(y)-CNTs. Inspiringly, the results indicate that VO(x)N(y)-CNTs catalyst exhibits a 0.4 mA/cm(2) larger diffusion-limited current density, a 0.10 V smaller onset potential value, a 10.73% less of ORR current decay and an excellent methanol-tolerance compared with commercial Pt/C catalyst. Therefore, we have reasonable grounds to believe that this new VO(x)N(y)-CNTs nanocomposites can be regarded as a promising non-precious methanol-tolerant ORR catalyst candidate for alkaline fuel cells.

SUBMITTER: Huang K

PROVIDER: S-EPMC4663630 | biostudies-other | 2015

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Development of Porous Pt Electrocatalysts for Oxygen Reduction and Evolution Reactions.

Project description:Porous Pt electrocatalysts have been developed as an example of carbon-free porous metal catalysts in anticipation of polymer electrolyte membrane (PEM) fuel cells and PEM water electrolyzers through the assembly of the metal precursor and surfactant. In this study, porous Pt was structurally evaluated and found to have a porous structure composed of connected Pt particles. The resulting specific electrochemical surface area (ECSA) of porous Pt was 12.4 m2 g-1, which was higher than that of commercially available Pt black. Accordingly, porous Pt showed higher oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activity than Pt black. When the activity was compared to that of a common carbon-supported electrocatalyst, Pt/ketjen black (KB), porous Pt showed a comparable ORR current density (2.5 mA cm-2 at 0.9 V for Pt/KB and 2.1 mA cm-2 at 0.9 V for porous Pt), and OER current density (6.8 mA cm-2 at 1.8 V for Pt/KB and 7.0 mA cm-1 at 1.8 V), even though the ECSA of porous Pt was only one-sixth that of Pt/KB. Moreover, it exhibited a higher durability against 1.8 V. In addition, when catalyst layers were spray-printed on the Nafion® membrane, porous Pt displayed more uniform layers in comparison to Pt black, showing an advantage in its usage as a thin layer.

| S-EPMC7287804 | biostudies-literature

Nitrogen-doped Graphene-Supported Transition-metals Carbide Electrocatalysts for Oxygen Reduction Reaction.

Project description:A novel and facile two-step strategy has been designed to prepare high performance bi-transition-metals (Fe- and Mo-) carbide supported on nitrogen-doped graphene (FeMo-NG) as electrocatalysts for oxygen reduction reactions (ORR). The as-synthesized FeMo carbide -NG catalysts exhibit excellent electrocatalytic activities for ORR in alkaline solution, with high onset potential (-0.09 V vs. saturated KCl Ag/AgCl), nearly four electron transfer number (nearly 4) and high kinetic-limiting current density (up to 3.5 mA cm(-2) at -0.8 V vs. Ag/AgCl). Furthermore, FeMo carbide -NG composites show good cycle stability and much better toxicity tolerance durability than the commercial Pt/C catalyst, paving their application in high-performance fuel cell and lithium-air batteries.

| S-EPMC4441168 | biostudies-literature

CoFe/N, S-C Featured with Graphitic Nanoribbons and Multiple CoFe Nanoparticles as Highly Stable and Efficient Electrocatalysts for the Oxygen Reduction Reaction.

Project description:The stability and activity of the catalysts are crucial for the oxygen reduction reaction (ORR) in fuel cells. Herein, CoFe/N, S-codoped biomass carbon (FB-CoFe-700) with graphitic nanoribbons and multiple CoFe nanoparticles was prepared through a facile thermal pyrolysis followed by an acid treatment process. The evolution of the growth of metal nanoparticles with the formation of graphite during the carbonization process was investigated. Inseparable from graphitic carbon-encased metal nanoparticles with the coexistence of graphitized nanoribbons and graphene-like sheets, FB-CoFe-700 exhibited a remarkable long-term electrocatalytic stability with 90.7% current retention after 50 000 s much superior to that of the commercially available Pt/C (20 wt %) in an alkaline medium. Meanwhile, FB-CoFe-700 displayed promising ORR catalytic activity (E 0 = 0.92 V vs reversible hydrogen electrode (RHE), E 1/2 = 0.82 V vs RHE, and n = 3.97) very similar to that of commercial Pt/C and outstanding methanol tolerance in an alkaline medium. This work is helpful for further development of nonprecious metal-doped carbon electrocatalysts with long-term stability.

| S-EPMC8153915 | biostudies-literature

Cyanogel-Derived Synthesis of Porous PdFe Nanohydrangeas as Electrocatalysts for Oxygen Reduction Reaction.

Project description:It is important to develop cost-efficient electrocatalysts used in the oxygen reduction reaction (ORR) for widespread applications in fuel cells. Palladium (Pd) is a promising catalyst, due to its more abundant reserves and lower price than platinum (Pt), and doping an earth-abundant 3d-transition metal M into Pd to form Pd-M bimetallic alloys may not only further reduce the use of expensive Pd but also promote the electrocatalytic performance of ORR, owing to the synergistic effect between Pd and M. Here we report a cyanogel-derived synthesis of PdFe alloys with porous nanostructure via a simple coinstantaneous reduction reaction by using K2PdIICl4/K4FeII(CN)6 cyanogel as precursor. The synthesized PdFe alloys possess hydrangea-like morphology and porous nanostructure, which are beneficial to the electrochemical performance in ORR. The onset potential of the porous PdFe nanohydrangeas is determined to be 0.988 V, which is much more positive than that of commercial Pt/C catalyst (0.976 V) and Pd black catalyst (0.964 V). Resulting from the unique structural advantages and synergetic effect between bimetals, the synthesized PdFe nanohydrangeas with porous structure have outstanding electrocatalytic activity and stability for ORR, compared with the commercial Pd black and Pt/C.

| S-EPMC8708350 | biostudies-literature

Reversible perovskite electrocatalysts for oxygen reduction/oxygen evolution.

Project description:The identification of electrocatalysts mediating both the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are prerequisite for the development of reversible fuel cells and rechargeable metal-air batteries. The question remains as to whether a bifunctional catalyst, or a single catalyst site, will exhibit potentials converging to +1.23 VRHE. Transition metal-based perovskites provide tunable catalysts where site substitution can influence both ORR and OER, however substitution in the pseudo-binary phases results in an anti-correlation in ORR and OER activities. We reveal that La x Mn y Ni1-y O3-δ , compositions with lanthanum A-site sub-stoichiometry exhibit reversible activity correlating with the appearance of the Mn3+/Mn4+ redox couple. The Mn3+/Mn4+ couple is associated with Mn4+ co-existing with Mn3+ in the bulk, as La3+ is substituted by Ni2+ at the A-site to create a mixed valent system. We also show that a direct A-site substitution by the Ca2+ cation in La x Ca1-x Mn y O3-δ perovskites also results in the creation of Mn4+, the appearance of the Mn3+/Mn4+ redox couple, and a concomitant reversible activity. These results highlight a general strategy of optimizing oxide electrocatalysts with reversible activity.

| S-EPMC6492633 | biostudies-literature

Noble-metal-free Co3S4-S/G porous hybrids as an efficient electrocatalyst for oxygen reduction reaction.

Project description:Developing of a new noble-metal-free catalyst to replace Pt-based catalysts of the oxygen reduction reaction (ORR) both in alkaline and acidic conditions is extremely significant for the fuel cell. In this paper, based on the pyrolysis of an inexpensive precursor cobalt dithiolene (a S4-chelate complex) on simultaneously reduced graphene oxide (GO) as a support matrix, a high-efficiency noble-metal-free hybrid for oxygen reduction reaction (ORR) consisting of Co3S4 nanoparticles encapsulated in porous sulfur doped graphene (referred as Co3S4-S/G) was fabricated. The catalyst obtained at 800 °C (Co3S4-S/G-800) manifests excellent oxygen reduction activity. Of note, the Co3S4-S/G-800 hybrids also exhibited prominent ORR activity with high selectivity (mainly 4e- reaction process) and very low H2O2 yield in acidic electrolyte. The optimal Co3S4-S/G-800 hybrid displayed much greater tolerance to methanol and higher stability than that of Pt/C. These admirable performances endorse Co3S4-S/G-800 electrocatalyst holding great potential for fuel cells. Meanwhile, this work also provides a simple and practical method to fabricate cobalt chalcogenides by using the cost-effective and easily synthesized S4-chelate complex.

| S-EPMC6014111 | biostudies-literature

Heteroatoms ternary-doped porous carbons derived from MOFs as metal-free electrocatalysts for oxygen reduction reaction.

Project description:The nitrogen (N), phosphorus (P) and sulphur (S) ternary-doped metal-free porous carbon materials have been successfully synthesized using MOFs as templates (denoted as NPS-C-MOF-5) for oxygen reduction reaction (ORR) for the first time. The influences of porous carbons from carbonizing different MOFs and carbonization temperature on ORR have been systematically investigated. Due to the synergistic effect of N, P and S ternary-doping, the NPS-C-MOF-5 catalyst shows a higher onset potential as a metal-free electrocatalyst for ORR among the currently reported metal-free electrocatalysts, very close to the commercial Pt-C catalyst. In particular, the kinetic limiting current density of NPS-C-MOF-5 catalyst at -0.6 V is up to approximate -11.6 mA cm(-2), which is 1.2 times higher than that of the commercial Pt-C catalyst. Furthermore, the outstanding methanol tolerance and excellent long-term stability of NPS-C-MOF-5 are superior to those of the commercial Pt-C catalyst for ORR in alkaline media.

| S-EPMC4038808 | biostudies-literature

Investigation of Supported Pd-Based Electrocatalysts for the Oxygen Reduction Reaction: Performance, Durability and Methanol Tolerance.

Project description:Next generation cathode catalysts for direct methanol fuel cells (DMFCs) must have high catalytic activity for the oxygen reduction reaction (ORR), a lower cost than benchmark Pt catalysts, and high stability and high tolerance to permeated methanol. In this study, palladium catalysts supported on titanium suboxides (Pd/TinO2n-1) were prepared by the sulphite complex route. The aim was to improve methanol tolerance and lower the cost associated with the noble metal while enhancing the stability through the use of titanium-based support; 30% Pd/Ketjenblack (Pd/KB) and 30% Pd/Vulcan (Pd/Vul) were also synthesized for comparison, using the same methodology. The catalysts were ex-situ characterized by physico-chemical analysis and investigated for the ORR to evaluate their activity, stability, and methanol tolerance properties. The Pd/KB catalyst showed the highest activity towards the ORR in perchloric acid solution. All Pd-based catalysts showed suitable tolerance to methanol poisoning, leading to higher ORR activity than a benchmark Pt/C catalyst in the presence of low methanol concentration. Among them, the Pd/TinO2n-1 catalyst showed a very promising stability compared to carbon-supported Pd samples in an accelerated degradation test of 1000 potential cycles. These results indicate good perspectives for the application of Pd/TinO2n-1 catalysts in DMFC cathodes.

| S-EPMC5458862 | biostudies-other

Titanium Dioxide/N-Doped Graphene Composites as Non-Noble Bifunctional Oxygen Electrocatalysts.

Project description:Bifunctional oxygen electrocatalysts are essential in the development of low-temperature unitized regenerative fuel cells (URFCs), as a promising alternative for storing energy via hydrogen. TiO2, as a semiconductor material, is commonly not established as an active electrocatalyst for oxygen reduction and oxygen evolution due to its poor electrical conductivity and low reactivity. Here, we demonstrated that composites composed of TiO2 and N-doped graphene can be active in oxygen reduction and evolution reactions in an alkaline environment. Combination factors such anatase/rutile interaction, N-doping graphene, and the presence of Ti3+/Ti-N species raise the active sites and improve the electrochemical activity. Our results may afford an opportunity to develop a non-noble and promising electrocatalyst in energy storage technology.

| S-EPMC9134212 | biostudies-literature

Highly Active and Stable Fe-N-C Oxygen Reduction Electrocatalysts Derived from Electrospinning and In Situ Pyrolysis.

Project description:High-performance electrocatalysts for the oxygen reduction reaction (ORR) are essential in electrochemical energy storage and conversion technologies. Fe-N-C electrocatalysts have been developed as one of the most promising alternatives to precious metal materials. Current M-N-C electrocatalysts usually are derived from high-temperature thermal treatment of a nitrogen-containing polymer or metal-organic frameworks (MOFs). Here, we developed Fe-N-C mesoporous nanofibers with low-cost urea and FeCl3 as the nitride and iron source; the electrocatalysts with abundant Fe-Nx active sites and large surface area were synthesized via electrospinning, in situ pyrolysis, and acid treatment process. The use of sealing conditions in the calcination process can effectively improve the nitrogen species content in the catalyst, which is important for improving performance. The as-prepared electrocatalyst material manifests well electrocatalytic performance for ORR in alkaline electrolyte (onset potential of 0.93 V and half-wave potential of 0.82 V); meanwhile, the electrocatalyst expresses good stability and methanol tolerance. This work may provide new thought for developing high-performance ORR electrocatalysts.

| S-EPMC6054600 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data