Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Femtosecond laser for cavity preparation in enamel and dentin: ablation efficiency related factors.

ABSTRACT: To study the effects of laser fluence (laser energy density), scanning line spacing and ablation depth on the efficiency of a femtosecond laser for three-dimensional ablation of enamel and dentin. A diode-pumped, thin-disk femtosecond laser (wavelength 1025 nm, pulse width 400 fs) was used for the ablation of enamel and dentin. The laser spot was guided in a series of overlapping parallel lines on enamel and dentin surfaces to form a three-dimensional cavity. The depth and volume of the ablated cavity was then measured under a 3D measurement microscope to determine the ablation efficiency. Different values of fluence, scanning line spacing and ablation depth were used to assess the effects of each variable on ablation efficiency. Ablation efficiencies for enamel and dentin were maximized at different laser fluences and number of scanning lines and decreased with increases in laser fluence or with increases in scanning line spacing beyond spot diameter or with increases in ablation depth. Laser fluence, scanning line spacing and ablation depth all significantly affected femtosecond laser ablation efficiency. Use of a reasonable control for each of these parameters will improve future clinical application.

SUBMITTER: Chen H

PROVIDER: S-EPMC4750072 | biostudies-other | 2016 Feb

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Laser ablation of silicon with THz bursts of femtosecond pulses.

Project description:In this work, we performed an experimental investigation supported by a theoretical analysis, to improve knowledge on the laser ablation of silicon with THz bursts of femtosecond laser pulses. Laser ablated craters have been created using 200 fs pulses at a wavelength of 1030 nm on silicon samples systematically varying the burst features and comparing to the normal pulse mode (NPM). Using bursts in general allowed reducing the thermal load to the material, however, at the expense of the ablation rate. The higher the number of pulses in the bursts and the lower the intra-burst frequency, the lower is the specific ablation rate. However, bursts at 2 THz led to a higher specific ablation rate compared to NPM, in a narrow window of parameters. Theoretical investigations based on the numerical solution of the density-dependent two temperature model revealed that lower lattice temperatures are reached with more pulses and lower intra-burst frequencies, thus supporting the experimental evidence of the lower thermal load in burst mode (BM). This is ascribed to the weaker transient drop of reflectivity, which suggests that with bursts less energy is transferred from the laser to the material. This also explains the trends of the specific ablation rates. Moreover, we found that two-photon absorption plays a fundamental role during BM processing in the THz frequency range.

| S-EPMC8233330 | biostudies-literature

Femtosecond Laser-assisted Preparation of Conjunctival Autograft for Pterygium Surgery.

Project description:Femtosecond laser-assisted conjunctival autografts (CAG) preparation was recently proposed. This study reports the outcomes of the first clinical trial on the use of laser to prepare CAG in pterygium surgery, and to compare the outcomes with those of manual technique. Forty eyes undergoing primary pterygium excision with laser-assisted CAG transplantation were prospectively included (L group). Two historical matched cohorts whose CAGs were prepared manually were compared (n = 78 eyes by the same experienced surgeon, M group; n = 78 eyes by trainees; TM group). We found the laser-created CAGs had only 11 μm deviation from the targeted thickness. The best-corrected visual acuity improved, and the astigmatism significantly decreased after surgery, with comparable efficacy across 3 groups. The 1-year recurrence rate was 2.5%, 3.8% and 7.7% in the L, M and TM groups, respectively (P = 0.12). There was no significant difference between the L and M groups in the complication rate (5.0% and 1.3%, respectively), surgical time (19.4 ± 5.1 and 19.1 ± 6.2 minutes, respectively), and postoperative discomfort scores (0.1 ± 0.3 and 0.2 ± 0.3, respectively), but these outcomes were significantly less favorable in the TM group. The results of this first comparative clinical trial suggest that femtosecond laser-assisted CAG preparation can be considered as an alternative technique for CAGs preparation.

| S-EPMC7021803 | biostudies-literature

Femtosecond laser ablation enhances cell infiltration into three-dimensional electrospun scaffolds.

Project description:Electrospun scaffolds are used extensively in tissue-engineering applications as they offer a cell-friendly microenvironment. However, one major limitation is the dense fibers, small pore size and consequently poor cell infiltration. Here, we employ a femtosecond (FS) laser system to ablate and create microscale features on electrospun poly(L-lactide) (PLLA) nanofibrous scaffolds. Upon determining the ablation parameters, we pattern structured holes with diameters of 50, 100 and 200 ?m and spacings of 50 and 200 ?m between adjacent holes on the scaffolds. The elastic moduli of ablated scaffolds decrease with the decrease in spacing and the increase in hole size. Cells seeded on the laser-ablated scaffolds exhibit different morphology but similar proliferation rate when compared with control (non-ablated) scaffold. Furthermore, animal studies indicate that ablated scaffolds facilitate endothelial cell ingrowth as well as drastically increase M2 macrophage and overall cell infiltration. These findings demonstrate that FS laser ablation can be used to increase cell infiltration into nanofibrous scaffolds. Laser ablation not only can create desired features in micrometer length scale but also presents a new approach in the fabrication of three-dimensional porous constructs for tissue engineering.

| S-EPMC3425609 | biostudies-literature

Fabrication of transition metal dichalcogenides quantum dots based on femtosecond laser ablation.

Project description:As heavy metal-free quantum dots, transition metal dichalcogenides (TMDs) and boron nitride (BN) quantum dots (QDs) have aroused great interest due to features such as good thermal conductivity, chemical stability, and unique optical properties. Although TMDs have been synthesized using different methods, most of these methods require time-consuming or complex steps, limiting the applications of TMDs. We propose a fast and simple method for the synthesis of high-quality molybdenum disulfide (MoS2) QDs and tungsten disulfide (WS2) QDs based on femtosecond laser ablation and sonication-assisted liquid exfoliation. The prepared MoS2 QDs and WS2 QDs were characterized by transmission electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy. The resulting products possessed few-layered thickness with an average size of 3.7?nm and 2.1?nm. Due to the abundance of functional groups on their surface, the MoS2 QDs and WS2 QDs showed bright blue-green luminescence under UV irradiation. Our method offers a facile and novel synthetic strategy for TMDs QDs and other two-dimensional nanomaterial quantum dots, such as boron nitride quantum dots (BNQDs).

| S-EPMC6393534 | biostudies-literature

Cutting off ciliary protein import: intraflagellar transport after dendritic femtosecond-laser ablation.

Project description:Primary cilia, organelles protruding from the surface of eukaryotic cells, act as cellular antennae to detect and transmit signals from the extracellular environment. They are built and maintained by continuous cycles of intraflagellar transport (IFT), where ciliary proteins are transported between the ciliary base and tip. These proteins originate from the cell body because cilia lack protein synthesis machinery. How input from the cell body affects IFT and ciliary function is not well understood. Here, we use femtosecond-laser ablation to perturb the dendritic input of proteins to chemosensory cilia in living Caenorhabditis elegans. Using fluorescence microscopy, we visualize and quantify the real-time response of ciliary proteins to dendritic ablation. We find that the response occurs in three distinct stages. First, IFT dynein is activated within seconds, redistributing IFT components toward the ciliary base; second, the ciliary axoneme shortens and motors slow down; and third, motors leave the cilium. Depletion of ATP by adding azide also results in IFT slowdown and IFT components leaving the cilium, but not in activation of retrograde IFT. These results indicate that laser ablation triggers a specific mechanism important for IFT regulation that allows the cilium to rapidly adapt to changes in the outside environment.

| S-EPMC7183794 | biostudies-literature

Two-dimensional fluorescence spectroscopy of uranium isotopes in femtosecond laser ablation plumes.

Project description:We demonstrate measurement of uranium isotopes in femtosecond laser ablation plumes using two-dimensional fluorescence spectroscopy (2DFS). The high-resolution, tunable CW-laser spectroscopy technique clearly distinguishes atomic absorption from 235U and 238U in natural and highly enriched uranium metal samples. We present analysis of spectral resolution and analytical performance of 2DFS as a function of ambient pressure. Simultaneous measurement using time-resolved absorption spectroscopy provides information on temporal dynamics of the laser ablation plume and saturation behavior of fluorescence signals. The rapid, non-contact measurement is promising for in-field, standoff measurements of uranium enrichment for nuclear safety and security.

| S-EPMC5476594 | biostudies-literature

From Femtosecond to Nanosecond Laser Microstructuring of Conical Aluminum Surfaces by Reactive Gas Assisted Laser Ablation.

Project description:A conical microstructure is one of the most versatile surface textures obtained by ultrashort laser micromachining. Besides an increased surface area, unique surface properties such as superhydrophilicity, increased absorptivity; and thermal emissivity can be tailored. On metals, usually ultrashort laser pulses in the femtosecond to low picosecond range are used to obtain these surface structures, whereas nanosecond laser pulses favor melting processes. Herein, we report on an investigation of reactive gas atmospheres such as oxygen, steam, and halogens during laser micromachining of aluminum with 6 ns laser pulses. At a reduced pressure of 20 hPa (air) with additional iodine vapor as reactive species, we found a perfectly microconical structured surface to be formed with nanosecond laser pulses. The resulting surface structures were proven to be free of residual halogens. The application of nanosecond instead of femtosecond laser pulses for the surface structuring process allows to apply significantly less complex laser sources.

| S-EPMC7496992 | biostudies-literature

Remineralization of Artificial Dentin Caries Using Dentin and Enamel Matrix Proteins.

Project description:To assess the remineralizing potential of dentin matrix proteins and enamel matrix derivatives (DMPs and EMDs) after application on artificially induced dentin lesions, given the hypothesis that these materials increase the mineral uptake, binding, and mineralization. Forty-eight caries-free human premolars were used. Teeth were cut, polished, and embedded, leaving an open window on the root surface, of which one-third was covered with a flowable composite to preserve the healthy untreated dentin. Then, samples were demineralized in Buskes solution for 33 days. A micro-CT scan prior to treatment was performed. Next, the samples were randomly allocated into four groups: (A) An untreated negative control (CON), (B) application of porcine dentin matrix proteins (DMP), (C) treatment with enamel matrix derivatives (EMD, Emdogain, Straumann), and (D) amine fluoride application (AMF, Elmex fluid, GABA). All samples were placed in artificial saliva for 21 days. A second micro-CT scan was performed, after which the change in gray scaling within a defined region of interest (0.25 mm3) was analyzed. ANCOVA was applied to discover statistical differences between the different treatments. Both, treatment with AMF; (P = 0.011 versus CON) as well as with DMP (P = 0.043 versus CON) yielded a statistically significant difference compared to the control treatment. EMD treatment was not found to differ (P > 0.05). Mainly the top layer of the defects showed clear signs of remineralization, which was also evident in CON. This study was able to visually confirm the remineralization potential of demineralized dentin especially after DMP application, which, however, did not outperform AMF. Based on this, additional studies combining proteins and fluorides are now warranted and ongoing.

| S-EPMC6651374 | biostudies-literature

Femtosecond Double-Pulse Laser Ablation and Deposition of Co-Doped ZnS Thin Films.

Project description:Nanostructured thin films of Co-doped zinc sulfide were synthesized through femtosecond pulsed laser deposition. The scheme involved ablation of physically mixed Co and ZnS with pairs of ultrashort pulses separated in time in the 0-300 ps range. In situ monitorization of the deposition process was carried out through a simultaneous reflectivity measurement. The crystallinity of generated nanoparticles and the inclusion of Co in the ZnS lattice is demonstrated by transmission electron microscopy and energy dispersive X-ray microanalysis (TEM-EDX) characterization. Surface morphology, Raman response, and photoluminescence of the films have also been assessed. The role of interpulse temporal separation is most visible in the thickness of the films obtained at the same total fluence, with much thicker films deposited with short delays than with individual uncoupled pulses. The proportion of Co in the synthesized doped ZnS nanoparticles is found to be substantially lower than the original proportion, and practically independent on interpulse delay.

| S-EPMC7698319 | biostudies-literature

Preparation of Monolayer MoS<sub>2</sub> Quantum Dots using Temporally Shaped Femtosecond Laser Ablation of Bulk MoS<sub>2</sub> Targets in Water.

Project description:Zero-dimensional MoS2 quantum dots (QDs) possess distinct physical and chemical properties, which have garnered them considerable attention and facilitates their use in a broad range of applications. In this study, we prepared monolayer MoS2 QDs using temporally shaped femtosecond laser ablation of bulk MoS2 targets in water. The morphology, crystal structures, chemical, and optical properties of the MoS2 QDs were characterized by transmission electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, UV-vis absorption spectra, and photoluminescence spectra. The analysis results show that highly pure, uniform, and monolayer MoS2 QDs can be successfully prepared. Moreover, by temporally shaping a conventional single pulse into a two-subpulse train, the production rate of MoS2 nanomaterials (including nanosheets, nanoparticles, and QDs) and the ratio of small size MoS2 QDs can be substantially improved. The underlying mechanism is a combination of multilevel photoexfoliation of monolayer MoS2 and water photoionization-enhanced light absorption. The as-prepared MoS2 QDs exhibit excellent electrocatalytic activity for hydrogen evolution reactions because of the abundant active edge sites, high specific surface area, and excellent electrical conductivity. Thus, this study provides a simple and green alternative strategy for the preparation of monolayer QDs of transition metal dichalcogenides or other layered materials.

| S-EPMC5593836 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data