Browse
Submit Data
Databases
API
Help

Dataset Information

11 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Study on Light Extraction from GaN-based Green Light-Emitting Diodes Using Anodic Aluminum Oxide Pattern and Nanoimprint Lithography.

ABSTRACT: An anodic aluminum oxide (AAO) patterned sapphire substrate, with the lattice constant of 520 ± 40 nm, pore dimension of 375 ± 50 nm, and height of 450 ± 25 nm was firstly used as a nanoimprint lithography (NIL) stamp and imprinted onto the surface of the green light-emitting diode (LED). A significant light extraction efficiency (LEE) was improved by 116% in comparison to that of the planar LED. A uniform broad protrusion in the central area and some sharp lobes were also obtained in the angular resolution photoluminescence (ARPL) for the AAO patterned LED. The mechanism of the enhancement was correlated to the fluctuations of the lattice constant and domain orientation of the AAO-pattern, which enabled the extraction of more guided modes from the LED device.

SUBMITTER: Jiang S

PROVIDER: S-EPMC4763243 | biostudies-other | 2016

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Hexagonal BN-Assisted Epitaxy of Strain Released GaN Films for True Green Light-Emitting Diodes.

Project description:Epitaxial growth of III-nitrides on 2D materials enables the realization of flexible optoelectronic devices for next-generation wearable applications. Unfortunately, it is difficult to obtain high-quality III-nitride epilayers on 2D materials such as hexagonal BN (h-BN) due to different atom hybridizations. Here, the epitaxy of single-crystalline GaN films on the chemically activated h-BN/Al2O3 substrates is reported, paying attention to interface atomic configuration. It is found that chemical-activated h-BN provides B-O-N and N-O bonds, where the latter ones act as effective artificial dangling bonds for following GaN nucleation, leading to Ga-polar GaN films with a flat surface. The h-BN is also found to be effective in modifying the compressive strain in GaN film and thus improves indium incorporation during the growth of InGaN quantum wells, resulting in the achievement of pure green light-emitting diodes. This work provides an effective way for III-nitrides epitaxy on h-BN and a possible route to overcome the epitaxial bottleneck of high indium content III-nitride light-emitting devices.

| S-EPMC7610270 | biostudies-literature

Carrier localization in In-rich InGaN/GaN multiple quantum wells for green light-emitting diodes.

Project description:Carrier localization phenomena in indium-rich InGaN/GaN multiple quantum wells (MQWs) grown on sapphire and GaN substrates were investigated. Temperature-dependent photoluminescence (PL) spectroscopy, ultraviolet near-field scanning optical microscopy (NSOM), and confocal time-resolved PL (TRPL) spectroscopy were employed to verify the correlation between carrier localization and crystal quality. From the spatially resolved PL measurements, we observed that the distribution and shape of luminescent clusters, which were known as an outcome of the carrier localization, are strongly affected by the crystalline quality. Spectroscopic analysis of the NSOM signal shows that carrier localization of MQWs with low crystalline quality is different from that of MQWs with high crystalline quality. This interrelation between carrier localization and crystal quality is well supported by confocal TRPL results.

| S-EPMC4366764 | biostudies-literature

Strong Geometrical Effects in Submillimeter Selective Area Growth and Light Extraction of GaN Light Emitting Diodes on Sapphire.

Project description:Advanced semiconductor devices often utilize structural and geometrical effects to tailor their characteristics and improve their performance. We report here detailed understanding of such geometrical effects in the epitaxial selective area growth of GaN on sapphire substrates and utilize them to enhance light extraction from GaN light emitting diodes. Systematic size and spacing effects were performed side-by-side on a single 2" sapphire substrate to minimize experimental sampling errors for a set of 144 pattern arrays with circular mask opening windows in SiO2. We show that the mask opening diameter leads to as much as 4 times increase in the thickness of the grown layers for 20??m spacings and that spacing effects can lead to as much as 3 times increase in thickness for a 350??m dot diameter. We observed that the facet evolution in comparison with extracted Ga adatom diffusion lengths directly influences the vertical and lateral overgrowth rates and can be controlled with pattern geometry. Such control over the facet development led to 2.5 times stronger electroluminescence characteristics from well-faceted GaN/InGaN multiple quantum well LEDs compared to non-faceted structures.

| S-EPMC4661445 | biostudies-literature

Ultraviolet GaN Light-Emitting Diodes with Porous-AlGaN Reflectors.

Project description:A GaN/AlGaN ultraviolet light emitting diode (UV-LED) structure with a porous AlGaN reflector structure has been demonstrated. Inside the UV-LED, the n+-AlGaN/undoped-AlGaN stack structure was transformed into a porous-AlGaN/undoped-AlGaN stack structure through a doping-selective electrochemical etching process. The reflectivity of the porous AlGaN reflector was 93% at 374 nm with a stop-bandwidth of 35 nm. In an angle-dependent reflectance measurement, the central wavelength of the porous AlGaN reflector had blueshift phenomenon by increasing light-incident angle from 10° to 50°. A cut-off wavelength was observed at 349 nm due to the material absorption of the porous-AlGaN/u-AlGaN stack structure. In the treated UV-LED structure, the photoluminescence emission wavelength was measured at 362 nm with a 106° divergent angle covered by the porous-AlGaN reflector. The light output power of the treated UV-LED structure was higher than that of the non-treated UV-LED structure due to the high light reflectance on the embedded porous AlGaN reflector.

| S-EPMC5504019 | biostudies-other

Effects of GaN/AlGaN/Sputtered AlN nucleation layers on performance of GaN-based ultraviolet light-emitting diodes.

Project description:We report on the demonstration of GaN-based ultraviolet light-emitting diodes (UV LEDs) emitting at 375 nm grown on patterned sapphire substrate (PSS) with in-situ low temperature GaN/AlGaN nucleation layers (NLs) and ex-situ sputtered AlN NL. The threading dislocation (TD) densities in GaN-based UV LEDs with GaN/AlGaN/sputtered AlN NLs were determined by high-resolution X-ray diffraction (XRD) and cross-sectional transmission electron microscopy (TEM), which revealed that the TD density in UV LED with AlGaN NL was the highest, whereas that in UV LED with sputtered AlN NL was the lowest. The light output power (LOP) of UV LED with AlGaN NL was 18.2% higher than that of UV LED with GaN NL owing to a decrease in the absorption of 375 nm UV light in the AlGaN NL with a larger bandgap. Using a sputtered AlN NL instead of the AlGaN NL, the LOP of UV LED was further enhanced by 11.3%, which is attributed to reduced TD density in InGaN/AlInGaN active region. In the sputtered AlN thickness range of 10-25 nm, the LOP of UV LED with 15-nm-thick sputtered AlN NL was the highest, revealing that optimum thickness of the sputtered AlN NL is around 15 nm.

| S-EPMC5353678 | biostudies-literature

Aluminum nitride nanowire light emitting diodes: Breaking the fundamental bottleneck of deep ultraviolet light sources.

Project description:Despite broad interest in aluminum gallium nitride (AlGaN) optoelectronic devices for deep ultraviolet (DUV) applications, the performance of conventional Al(Ga)N planar devices drastically decays when approaching the AlN end, including low internal quantum efficiencies (IQEs) and high device operation voltages. Here we show that these challenges can be addressed by utilizing nitrogen (N) polar Al(Ga)N nanowires grown directly on Si substrate. By carefully tuning the synthesis conditions, a record IQE of 80% can be realized with N-polar AlN nanowires, which is nearly ten times higher compared to high quality planar AlN. The first 210 nm emitting AlN nanowire light emitting diodes (LEDs) were achieved, with a turn on voltage of about 6 V, which is significantly lower than the commonly observed 20 - 40 V. This can be ascribed to both efficient Mg doping by controlling the nanowire growth rate and N-polarity induced internal electrical field that favors hole injection. In the end, high performance N-polar AlGaN nanowire LEDs with emission wavelengths covering the UV-B/C bands were also demonstrated.

| S-EPMC4329565 | biostudies-literature

Remote heteroepitaxy of GaN microrod heterostructures for deformable light-emitting diodes and wafer recycle.

Project description:There have been rapidly increasing demands for flexible lighting apparatus, and micrometer-scale light-emitting diodes (LEDs) are regarded as one of the promising lighting sources for deformable device applications. Herein, we demonstrate a method of creating a deformable LED, based on remote heteroepitaxy of GaN microrod (MR) p-n junction arrays on c-Al2O3 wafer across graphene. The use of graphene allows the transfer of MR LED arrays onto a copper plate, and spatially separate MR arrays offer ideal device geometry suitable for deformable LED in various shapes without serious device performance degradation. Moreover, remote heteroepitaxy also allows the wafer to be reused, allowing reproducible production of MR LEDs using a single substrate without noticeable device degradation. The remote heteroepitaxial relation is determined by high-resolution scanning transmission electron microscopy, and the density functional theory simulations clarify how the remote heteroepitaxy is made possible through graphene.

| S-EPMC7269673 | biostudies-literature

Less strained and more efficient GaN light-emitting diodes with embedded silica hollow nanospheres.

Project description:Light-emitting diodes (LEDs) become an attractive alternative to conventional light sources due to high efficiency and long lifetime. However, different material properties between GaN and sapphire cause several problems such as high defect density in GaN, serious wafer bowing, particularly in large-area wafers, and poor light extraction of GaN-based LEDs. Here, we suggest a new growth strategy for high efficiency LEDs by incorporating silica hollow nanospheres (S-HNS). In this strategy, S-HNSs were introduced as a monolayer on a sapphire substrate and the subsequent growth of GaN by metalorganic chemical vapor deposition results in improved crystal quality due to nano-scale lateral epitaxial overgrowth. Moreover, well-defined voids embedded at the GaN/sapphire interface help scatter lights effectively for improved light extraction, and reduce wafer bowing due to partial alleviation of compressive stress in GaN. The incorporation of S-HNS into LEDs is thus quite advantageous in achieving high efficiency LEDs for solid-state lighting.

| S-EPMC3826094 | biostudies-literature

A solution processed flexible nanocomposite electrode with efficient light extraction for organic light emitting diodes.

Project description:Highly efficient organic light emitting diodes (OLEDs) based on multiple layers of vapor evaporated small molecules, indium tin oxide transparent electrode, and glass substrate have been extensively investigated and are being commercialized. The light extraction from the exciton radiative decay is limited to less than 30% due to plasmonic quenching on the metallic cathode and the waveguide in the multi-layer sandwich structure. Here we report a flexible nanocomposite electrode comprising single-walled carbon nanotubes and silver nanowires stacked and embedded in the surface of a polymer substrate. Nanoparticles of barium strontium titanate are dispersed within the substrate to enhance light extraction efficiency. Green polymer OLED (PLEDs) fabricated on the nanocomposite electrode exhibit a maximum current efficiency of 118?cd/A at 10,000?cd/m(2) with the calculated external quantum efficiency being 38.9%. The efficiencies of white PLEDs are 46.7?cd/A and 30.5%, respectively. The devices can be bent to 3?mm radius repeatedly without significant loss of electroluminescent performance. The nanocomposite electrode could pave the way to high-efficiency flexible OLEDs with simplified device structure and low fabrication cost.

| S-EPMC3955904 | biostudies-literature

Efficient metal halide perovskite light-emitting diodes with significantly improved light extraction on nanophotonic substrates.

Project description:Metal halide perovskite has emerged as a promising material for light-emitting diodes. In the past, the performance of devices has been improved mainly by optimizing the active and charge injection layers. However, the large refractive index difference among different materials limits the overall light extraction. Herein, we fabricate efficient methylammonium lead bromide light-emitting diodes on nanophotonic substrates with an optimal device external quantum efficiency of 17.5% which is around twice of the record for the planar device based on this material system. Furthermore, optical modelling shows that a high light extraction efficiency of 73.6% can be achieved as a result of a two-step light extraction process involving nanodome light couplers and nanowire optical antennas on the nanophotonic substrate. These results suggest that utilization of nanophotonic structures can be an effective approach to achieve high performance perovskite light-emitting diodes.

| S-EPMC6374404 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data