"Pop-slide" patterning: Rapid fabrication of microstructured PDMS gasket slides for biological applications.
Ontology highlight
ABSTRACT:
SUBMITTER: Ramji R
PROVIDER: S-EPMC4772973 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Publications
"Pop-slide" patterning: Rapid fabrication of microstructured PDMS gasket slides for biological applications.
Ramji Ramesh R Khan Nafeesa T NT Muñoz-Rojas Andrés A Miller-Jensen Kathryn K
RSC advances 20150804 81
We describe a "pop-slide" patterning approach to easily produce thin film microstructures on the surface of glass with varying feature sizes (3 μm - 250 μm) and aspect ratios (0.066 - 3) within 45 minutes. This low cost method does not require specialized equipment while allowing us to produce micro structured gasket layers for sandwich assays and could be readily applied to many biological applications. ...[more]
Similar Datasets
Project description:Even though porous elastomers and elastomeric nanocomposites have shown many advantages for triboelectric nanogenerators (TENGs), their fabrication techniques are relatively complicated, inefficient, and time-consuming. In this work, we introduced a simple, efficient and rapid concept to fabricate porous polydimethylsiloxane (PDMS) nanocomposites. PDMS nanocomposites with various porous structure were produced within a few minutes through just one-step microwave irradiation without any post-processing. Three solvents with different boiling points were selected as sacrificial materials to control porous structure. To fabricate nanocomposites, BaTiO3 (BT) nanoparticles were mixed into the uncured PDMS and sacrificial solvent mixture. Additionally, Ni nanoparticles were also used to understand the effect of embedded material's property on porous structure. The porous BT/PDMS nanocomposites fabricated via microwave irradiation greatly enhanced the electrical performance of TENGs as compared to a pure solid elastomer. The present study provides a simple, rapid and inexpensive approach for fabricating TENGs based on porous elastomeric nanocomposites.
| S-EPMC6155244 | biostudies-literature
Project description:Multicellular patterning of stem-cell-derived tissue models is commonly achieved via self-organizing activities triggered by exogenous morphogenetic stimuli. However, such tissue models are prone to stochastic behavior, limiting the reproducibility of cellular composition and forming non-physiological architectures. To enhance multicellular patterning in stem cell-derived tissues, a method for creating complex tissue microenvironments endowed with programmable multimodal mechano-chemical cues, including conjugated peptides, proteins, morphogens, and Young's moduli defined over a range of stiffnesses is developed. The ability of these cues to spatially guide tissue patterning processes, including mechanosensing and the biochemically driven differentiation of selected cell types, is demonstrated. By rationally designing niches, the authors engineered a bone-fat assembly from stromal mesenchyme cells and regionalized germ layer tissues from pluripotent stem cells. Through defined niche-material interactions, mechano-chemically microstructured niches enable the spatial programming of tissue patterning processes. Mechano-chemically microstructured cell niches thereby offer an entry point for enhancing the organization and composition of engineered tissues, potentiating structures that better recapitulate their native counterparts.
| S-EPMC10214222 | biostudies-literature
Project description:Monodisperse polyvinyl alcohol (PVA) microspheres have been widely used for targeted drug delivery, embolization, and templates. However, the fast and facile fabrication of PVA microspheres with uniform size and internal structure and good sphericity remains a challenge. In this study, the PVA microspheres with uniformity in the size, shape, and internal structure were rapidly fabricated, using single-emulsion droplet templates by an on-chip approach. First, we designed a polydimethylsiloxane (PDMS) microfluidic chip integrated with three functional units, used for the droplet generation, mixing of reagents, and pre-curing of PVA microspheres, respectively. Then, we precisely controlled the generation of PVA aqueous droplets, mixing of reagents, and the gelation rate for the production of high-quality microspheres by adjusting the pH value, flow rate, and the channel structure. The prepared PVA microspheres are characterized with good sphericity, uniform internal structure, and narrow size distribution. The microspheres have good adsorption capacity and recyclability for small-molecule drugs, as demonstrated by the adsorption and desorption of methylene blue (MB). The adsorption behavior is well described by the pseudo-second-order model, and intraparticle diffusion is as fast as the external film diffusion.
| S-EPMC6888467 | biostudies-literature
Project description:Microfluidic devices allow for the manipulation of fluids, particles, cells, micro-sized organs or organisms in channels ranging from the nano to submillimeter scales. A rapid increase in the use of this technology in the biological sciences has prompted a need for methods that are accessible to a wide range of research groups. Current fabrication standards, such as PDMS bonding, require expensive and time consuming lithographic and bonding techniques. A viable alternative is the use of equipment and materials that are easily affordable, require minimal expertise and allow for the rapid iteration of designs. In this work we describe a protocol for designing and producing PET-laminates (PETLs), microfluidic devices that are inexpensive, easy to fabricate, and consume significantly less time to generate than other approaches to microfluidics technology. They consist of thermally bonded film sheets, in which channels and other features are defined using a craft cutter. PETLs solve field-specific technical challenges while dramatically reducing obstacles to adoption. This approach facilitates the accessibility of microfluidics devices in both research and educational settings, providing a reliable platform for new methods of inquiry.
| S-EPMC7390482 | biostudies-literature
Project description:Self-organized patterning of mammalian embryonic stem cells on micropatterned surfaces has previously been established as an in vitro platform for early mammalian developmental studies, complimentary to in vivo studies. Traditional micropatterning methods, such as micro-contact printing (μCP), involve relatively complicated fabrication procedures, which restricts widespread adoption by biologists. Here, we demonstrate a rapid method of micropatterning by printing hydrogel micro-features onto a glass-bottomed culture vessel. The micro-features are printed using a projection stereolithography bioprinter yielding hydrogel structures that geometrically restrict the attachment of cells or proteins. Compared to traditional and physical photomasks, a digitally tunable virtual photomask is used in the projector to generate blue light patterns that enable rapid iteration with minimal cost and effort. We show that a protocol that makes use of this method together with LN521 coating, an extracellular matrix coating, creates a surface suitable for human embryonic stem cell (hESC) attachment and growth with minimal non-specific adhesion. We further demonstrate that self-patterning of hESCs following previously published gastrulation and ectodermal induction protocols achieves results comparable with those obtained with commercially available plates.
| S-EPMC8172057 | biostudies-literature
Project description:Micro-contact printing, μCP, is a well-established soft-lithography technique for printing biomolecules. μCP uses stamps made of Poly(dimethylsiloxane), PDMS, made by replicating a microstructured silicon master fabricated by semiconductor manufacturing processes. One of the problems of the μCP is the difficult control of the printing process, which, because of the high compressibility of PDMS, is very sensitive to minute changes in the applied pressure. This over-sensitive response leads to frequent and/or uncontrollable collapse of the stamps with high aspect ratios, thus decreasing the printing accuracy and reproducibility. Here we present a straightforward methodology of designing and fabricating PDMS structures with an architecture which uses the collapse of the stamp to reduce, rather than enlarge the variability of the printing. The PDMS stamp, organized as an array of pyramidal micro-posts, whose ceiling collapses when pressed on a flat surface, replicates the structure of the silicon master fabricated by anisotropic wet etching. Upon application of pressure, depending on the size of, and the pitch between, the PDMS pyramids, an air gap is formed surrounding either the entire array, or individual posts. The printing technology, which also exhibits a remarkably low background noise for fluorescence detection, may find applications when the clear demarcation of the shapes of protein patterns and the distance between them are critical, such as microarrays and studies of cell patterning.
| S-EPMC4718951 | biostudies-literature
Project description:Poly(dimethylsiloxane) has attracted much attention in soft lithography and has also been preferred as a platform for a photochemical reaction, thanks to its outstanding characteristics including ease of use, nontoxicity, and high optical transmittance. However, the low stiffness of PDMS, an obvious advantage for soft lithography, is often treated as an obstacle in conducting precise handling or maintaining its structural integrity. For these reasons, a Glass-PDMS-Glass structure has emerged as a straightforward alternative. Nevertheless, several challenges are remaining in fabricating Glass-PDMS-Glass structure through the conventional PDMS patterning techniques such as photolithography and etching processes for master mold. The complicated techniques are not suitable for frequent design modifications in research-oriented fields, and fabrication of perforated PDMS is hard to achieve using mold replication. Herein, we utilize the successive laser pyrolysis technique to pattern thin-film PDMS for microfluidic applications. The direct use of thin film at the glass surface prevents the difficulties of thin-film handling. Through the precise control of photothermal pyrolysis phenomena, we provide a facile fabrication process for perforated PDMS microchannels. In the final demonstration, the laminar flow has been successfully created owing to the smooth surface profile. We envision further applications using rapid prototyping of the perforated PDMS microchannel.
| S-EPMC8658685 | biostudies-literature
Project description:BackgroundIn addition to the widespread use of antibiotics in healthcare settings, the current COVID-19 pandemic has escalated the emergence of antibiotic resistance. Nosocomial infections among hospitalized patients is a leading site for such resistant microbial colonization due to prolonged use of invasive devices and antibiotics in therapies. Invasive medical devices, especially catheters, are prone to infections that could accelerate the development of resistant microbes. Often, catheters - particularly urinary catheters - are prone to high infection rates. Antibiotic-coated catheters can reduce infection rates and although commercially available, are limited in efficacy and choices.MethodsHerein, a novel and facile method to fabricate PMDS-based biomaterial for the development of antimicrobial eluting catheters is presented. Silicone based organic polymer polydimethylsiloxane (PDMS) was used to prepare a biomaterial containing novel polymeric imidazolium antimicrobial compound.ResultsIt was found that the PDMS-based biomaterials could eradicate microbial colonization even after 60 days in culture with continuous microbial challenge, be recycled over multiple uses, stored at room temperature for long-term usage and importantly is biocompatible.ConclusionThe PDMS-based biomaterial displayed biocidal functionality on microbes of clinical origin, which form major threats in hospital acquired infections.
| S-EPMC8529379 | biostudies-literature
Project description:Several marine bacteria of the Roseobacter group can inhibit other microorganisms and are especially antagonistic when growing in biofilms. This aptitude to naturally compete with other bacteria can reduce the need for antibiotics in large-scale aquaculture units, provided that their culture can be promoted and controlled. Micropatterned surfaces may facilitate and promote the biofilm formation of species from the Roseobacter group, due to the increased contact between the cells and the surface material. Our research goal is to fabricate biofilm-optimal micropatterned surfaces and investigate the relevant length scales for surface topographies that can promote the growth and biofilm formation of the Roseobacter group of bacteria. In a preliminary study, silicon surfaces comprising arrays of pillars and pits with different periodicities, diameters, and depths were produced by UV lithography and deep reactive ion etching (DRIE) on polished silicon wafers. The resulting surface microscale topologies were characterized via optical profilometry and scanning electron microscopy (SEM). Screening of the bacterial biofilm on the patterned surfaces was performed using green fluorescent staining (SYBR green I) and confocal laser scanning microscopy (CLSM). Our results indicate that there is a correlation between the surface morphology and the spatial organization of the bacterial biofilm.
| S-EPMC8401315 | biostudies-literature
Project description:Poly(dimethylsiloxane) (PDMS) microstructures have been widely used in bio-microelectromechanical systems (bio-MEMS) for various types of analytical, diagnostic and therapeutic applications. However, PDMS-based soft lithographic techniques still use conventional microfabrication processes to generate a master mold, which requires access to clean room facilities and costly equipment. With the increasing use of these systems in various fields, the development of benchtop systems for fabricating microdevices is emerging as an important challenge in their widespread use. Here we demonstrate a simple, low-cost and rapid method to fabricate PDMS microstructures by using micropatterned poly(ethylene glycol) diacrylate (PEGDA) master molds. In this method, PEGDA microstructures were patterned on a glass substrate by photolithography under ambient conditions and by using simple tools. The resulting PEGDA structures were subsequently used to generate PDMS microstructures by standard molding in a reproducible and repeatable manner. The thickness of the PEGDA microstructures was controllable from 15 to 300 µm by using commonly available spacer materials. We also demonstrate the use of this method to fabricate microfluidic channels capable of generating concentration gradients. In addition, we fabricated PEGDA microstructures by photolithography from the light generated from commonly available laminar cell culture hood. These data suggest that this approach could be beneficial for fabricating low-cost PDMS-based microdevices in resource limited settings.
| S-EPMC3005377 | biostudies-literature