Ti-Ag-Pd alloy with good mechanical properties and high potential for biological applications.
Ontology highlight
ABSTRACT:
SUBMITTER: Zadorozhnyy VY
PROVIDER: S-EPMC4848501 | biostudies-other | 2016 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The performance of current biomedical titanium alloys is limited by inflammatory and severe inflammatory conditions after implantation. In this study, a novel Ti-Nb-Zr-Si (TNZS) alloy was developed and compared with commercially pure titanium, and Ti-6Al-4V alloy. Electrochemical parameters of specimens were monitored during 1 h and 12 h immersion in phosphate buffered saline (PBS) as a normal, PBS/hydrogen peroxide (H2O2) as an inflammatory, and PBS/H2O2/albumin/lactate as a severe inflammatory media. The results showed an effect of the H2O2 in inflammatory condition and the synergistic behavior of H2O2, albumin, and lactate in severe inflammatory condition towards decreasing the corrosion resistance of titanium biomaterials. Electrochemical tests revealed a superior corrosion resistance of the TNZS in all conditions due to the presence of silicide phases. The developed TNZS was tested for subsequent cell culture investigation to understand its biocompatibility nature. It exhibited favorable cell-materials interactions in vitro compared with Ti-6Al-4V. The results suggest that TNZS alloy might be a competitive biomaterial for orthopedic applications.
| S-EPMC9911760 | biostudies-literature
Project description:Most transparent conducting materials are based on Sn:In2O3 (ITO). When applied onto flexible substrates, ITO can be prepared in an oxide-metal-oxide (OMO) configuration, typically ITO/Ag/ITO, where the ductility of the embedded metal layer is intended to reduce the mechanical brittleness and improve the electrical conductivity of the OMO multilayer. Hitherto, the lower limit of the thickness of the Ag layer has been limited by the percolation threshold, which limits the Ag layer to be thicker than ∼10 nm to avoid agglomeration and to ensure conductivity and structural stability. Metal layers of thicknesses below 10 nm are, however, desirable for obtaining OMO coatings with better optical properties. It is known that agglomeration of the metal layer can, to some extent, be suppressed when substituting Ag by an Ag-Pd-Cu (APC) alloy. APC-based OMO films exhibit excellent optical and electrical properties, but still continuous APC films well below 10 nm thickness cannot be achieved. In this work we demonstrate that controlled oxidation of APC results in smooth, ultrathin APC:O continuous coatings (of thickness ∼5 nm) on ITO-coated PET substrates. Moderate oxidation yields superficial PdOx formation, which suppresses Ag agglomeration, while still maintaining excellent conductivity. On the other hand, extensive oxidation of APC leads to extensive Pd oxide nucleation deteriorating the conductivity of the film. The ITO/APC:O/ITO films exhibit low resistivity, attributed to a high Hall mobility associated with suppressed agglomeration, good stability in high humidity/temperature environments, superior transmittance in the visible and infrared region, and excellent mechanical bending properties, thus providing new opportunities for fabricating superior transparent conducting coatings on polymer substrates.
| S-EPMC8990516 | biostudies-literature
Project description:A sophisticated understanding of phase transformations and microstructure evolution is crucial in mechanical property optimization for the newly developed low-cost Ti-35421 (Ti-3Al-5Mo-4Cr-2Zr-1Fe wt.%) titanium alloy. The phase transformations in dual-phase Ti-35421 were studied by experiments and thermo-kinetic modeling. The phase transformation reactions and temperature ranges were determined as ???lamellar [410-660 °C], ?lamellar?? [660-740 °C], ?lath?? [740-825 °C]. The Gibbs-Thomson effect and multicomponent diffusivities were proven to be responsible for the distinguishing behaviors of growth and dissolution between two ? phases. The aging temperature of 540 °C was optimized based on calculations. It introduced a bimodal microstructure containing stubby ? lamellae and ? matrix. The mechanical properties of bimodal Ti-35421 were tested and compared with baseline alloy Ti-B19 and other near-? titanium alloys. The 540 °C aged alloy exhibits an optimal combination of mechanical properties with tensile strength of 1313 MPa, yield strength of 1240 MPa, elongation of 8.62%, and fracture toughness of 75.8 MPa·m1/2. The bimodal Ti-35421 shows comparable performance to Ti-B19 but has lower cost in raw materials and processing. The results also demonstrate that thermo-kinetic modeling can effectively be utilized in tailoring microstructure and enhancing mechanical properties.
| S-EPMC6747788 | biostudies-literature
Project description:Highlights • Ti-8Mo-2Fe was resistant to pitting corrosion in PBS, a clear advantage over 316 L.• Ti-8Mo-2Fe exhibited similar corrosion rate in PBS than pure ti and 316 L.• Ti-8Mo-2Fe alloy did not generate acute hemolysis.• Blood coagulation was retarded on ti-8mo-2fe surface in comparison to pure Ti.• The proliferation rate of ECs and SMCs on ti-8mo-2fe was lower than on 316 L. There is a deep interest in developing new Ni-free Ti-based alloys to replace 316 L stainless steel and Co-Cr alloys for endovascular stent application, mainly because the release of Ni can generate toxicity and allergenicity. Interactions of Ti alloy biomaterials with bone cells and tissues have been widely investigated and reported, while interactions with vascular cells and tissues, such as endothelial cells (ECs) and smooth muscle cells (SMCs), are scarce. Therefore, this study focused on the relationship among the surface finishing features, corrosion behavior and in vitro biological performances regarding human ECs, SMCs and blood of a newly developed Ti-8Mo-2Fe (TMF) alloy, specifically designed for balloon-expandable stent applications. The alloy performances were compared to those of 316 L and pure Ti, prepared with the same surface finishing techniques, which are mechanical polishing and electropolishing. Surface properties were investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM), contact angle (CA) and x-ray photoelectron spectroscopy (XPS). The corrosion behavior was assessed with potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) tests in phosphate buffered saline (PBS) solution. No significant differences were observed regarding the corrosion rate measured with PDP analyses, which was of the order of 2 × 10−4 mm/y for all the studied materials. Moreover, similarly to pure Ti, TMF exhibited an advantage over 316 L for biomedical applications, namely remarkable resistance to pitting corrosion up to high potentials. The results evidenced a good cytocompatibility and hemocompatibility, making this group of alloy a potential candidate for cardiovascular implants. In fact, both ECs and SMCs proliferated on TMF surfaces showing a 7-day viability similar to that of pure Ti. Regarding hemocompatibility, TMF did not cause hemolysis, and blood coagulation was delayed on its surface in comparison to pure Ti. When compared to 316 L, TMF showed similar hemocompatibility.
| S-EPMC10240522 | biostudies-literature
Project description:This work systematically analysed the electrochemical and corrosion behaviour of Ti-Ta-Ag ternary alloy samples in Hank's solution. For the samples with 1.5% and 3% Ag content, the sintering temperature increased from 750 to 950°C, and the corresponding corrosion resistance increased by 100 times due to the increased alloying of Ag; meanwhile for the sample with 4.5% Ag content, the sintering temperature increased from 750 to 950°C, and the corresponding corrosion resistance decreased by six times due to the increased precipitation of Ag. These tests prove that the Ag alloying is beneficial to the enhancement of the corrosion resistance of Ti-Ta-Ag ternary alloy, but the Ag trace precipitation has the opposite effect. A series of electrochemical characterizations and density functional theory calculations explain the mechanism of the above phenomenon. Ag alloying can promote the formation of uniform, complete, dense, stable and thick passivation layer on the surface of Ti-Ta-Ag ternary alloy, which makes Ti-Ta-Ag ternary alloy uniformly corroded without pitting. In addition, Ag alloying can effectively reduce the contact resistance of the solid-liquid interface. However, the trace precipitation of Ag plays the opposite role to the above effect.
| S-EPMC8441115 | biostudies-literature
Project description:Titanium alloys are receiving increasing research interest for the development of metallic stent materials due to their excellent biocompatibility, corrosion resistance, non-magnetism and radiopacity. In this study, a new series of Ti-Ta-Hf-Zr (TTHZ) alloys including Ti-37Ta-26Hf-13Zr, Ti-40Ta-22Hf-11.7Zr and Ti-45Ta-18.4Hf-10Zr (wt.%) were designed using the d-electron theory combined with electron to atom ratio (e/a) and molybdenum equivalence (Moeq) approaches. The microstructure of the TTHZ alloys were investigated using optical microscopy, XRD, SEM and TEM and the mechanical properties were tested using a Vickers micro-indenter, compression and tensile testing machines. The cytocompatibility of the alloys was assessed using osteoblast-like cells in vitro. The as-cast TTHZ alloys consisted of primarily ? and ? nanoparticles and their tensile strength, yield strength, Young's modulus and elastic admissible strain were measured as being between 1000.7-1172.8 MPa, 1000.7-1132.2 MPa, 71.7-79.1 GPa and 1.32-1.58%, respectively. The compressive yield strength of the as-cast alloys ranged from 1137.0 to 1158.0 MPa. The TTHZ alloys exhibited excellent cytocompatibility as indicated by their high cell viability ratios, which were close to that of CP-Ti. The TTHZ alloys can be anticipated to be promising metallic stent materials by virtue of the unique combination of extraordinarily high elastic admissible strain, high mechanical strength and excellent biocompatibility.
| S-EPMC5126583 | biostudies-literature
Project description:Nickel-titanium-oxide (Ni-Ti-O) nanotube arrays (NTAs) prepared on nearly equiatomic NiTi alloy shall have broad application potential such as for energy storage and biomedicine, but their precise structure control is a great challenge because of the high content of alloying element of Ni, a non-valve metal that cannot form a compact electronic insulating passive layer when anodized. In the present work, we systemically investigated the influence of various anodization parameters on the formation and structure of Ni-Ti-O NTAs and their potential applications. Our results show that well controlled NTAs can be fabricated during relatively wide ranges of the anodization voltage (5-90 V), electrolyte temperature (10-50°C) and electrolyte NH4F content (0.025-0.8 wt%) but within a narrow window of the electrolyte H2O content (0.0-1.0 vol%). Through modulating these parameters, the Ni-Ti-O NTAs with different diameter (15-70 nm) and length (45-1320 nm) can be produced in a controlled manner. Regarding potential applications, the Ni-Ti-O NTAs may be used as electrodes for electrochemical energy storage and non-enzymic glucose detection, and may constitute nanoscaled biofunctional coating to improve the biological performance of NiTi based biomedical implants.
| S-EPMC4269879 | biostudies-literature
Project description:Multi-pass hot rolling was performed on bi-modal Ti-55511 alloy with 50% rolling reduction at 700 °C. Mechanical properties were evaluated by tensile test, and microstructure evolution was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the Ti-55511 alloy with bi-modal microstructure exhibits good strength and high ductility (1102 MPa, 21.7%). Comparatively, after 50% hot rolling, an enhanced strength and decreased ductility were obtained. The refinement of ? phases leads to the increased tensile strength, while the fragmentation of the equiaxed ? phase results in a decreased ductility. The fragmentation process of equiaxed ? phases followed the sequence of: elongation of ? phases ? formation of grooves and localized shear bands ? the final fragmentation accomplished via deepening grooves.
| S-EPMC7435951 | biostudies-literature
Project description:The Ti-15Mo alloy has its mechanical properties strongly altered by heat treatments and by addition of interstitial elements, such as, oxygen, for example. In this sense, the objective of this paper is to analyze the effect of the introduction of oxygen in selected mechanical properties and the biocompatibility of Ti-15Mo alloy. The samples used in this study were prepared by arc-melting and characterized by density measurements, X-ray diffraction, scanning electron microscopy, microhardness, modulus of elasticity, and biocompatibility tests. Hardness measurements were shown to be sensitive to concentration of oxygen. The modulus results showed interstitial influence in value; this was verified under several conditions to which the samples were exposed. Cytotoxicity tests conducted in vitro showed that the various processing conditions did not alter the biocompatibility of the material.
| S-EPMC5453156 | biostudies-other
Project description:This work illustrates the effect of thermal mechanical processing parameters on the microstructure and mechanical properties of the Ti-22Al-25Nb alloy prepared by reactive sintering with element powders, consisting of O, B2 and Ti₃Al phases. Tensile and plane strain fracture toughness tests were carried out at room temperature to understand the mechanical behavior of the alloys and its correlation with the microstructural features characterized by scanning and transmission electron microscopy. The results show that the increased tensile strength (from 340 to 500 MPa) and elongation (from 3.6% to 4.2%) is due to the presence of lamellar O/B2 colony and needle-like O phase in B2 matrix in the as-processed Ti-22Al-25Nb alloys, as compared to the coarse lath O adjacent to B2 in the sintered alloys. Changes in morphologies of O phase improve the fracture toughness (KIC) of the sintered alloys from 7 to 15 MPa·m-1/2. Additionally, the fracture mechanism shifts from cleavage fracture in the as-sintered alloys to quasi-cleavage fracture in the as-processed alloys.
| S-EPMC5456733 | biostudies-other