A new hand-held optical reflectometer to measure enamel erosion: correlation with surface hardness and calcium release.
Ontology highlight
ABSTRACT:
SUBMITTER: Carvalho TS
PROVIDER: S-EPMC4848505 | biostudies-other | 2016 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:We present assembly and application of an optical reflectometer for the analysis of dental erosion. The erosive procedure involved acid-induced softening and initial substance loss phases, which are considered to be difficult for visual diagnosis in a clinic. Change of the specular reflection signal showed the highest sensitivity for the detection of the early softening phase of erosion among tested methods. The exponential decrease of the specular reflection intensity with erosive duration was compared to the increase of enamel roughness. Surface roughness was measured by optical analysis, and the observed tendency was correlated with scanning electron microscopy images of eroded enamel. A high correlation between specular reflection intensity and measurement of enamel softening (r(2) ≥ -0.86) as well as calcium release (r(2) ≥ -0.86) was found during erosion progression. Measurement of diffuse reflection revealed higher tooth-to-tooth deviation in contrast to the analysis of specular reflection intensity and lower correlation with other applied methods (r(2) = 0.42-0.48). The proposed optical method allows simple and fast surface analysis and could be used for further optimization and construction of the first noncontact and cost-effective diagnostic tool for early erosion assessment in vivo.
| S-EPMC3206927 | biostudies-other
Project description:X-ray mammography, the current gold standard for breast cancer detection, has a 20% false-negative rate (cancer is undetected) and increases in younger women with denser breast tissue. Diffuse optical imaging (DOI) is a safe (nonionizing), and relatively inexpensive method for noninvasive imaging of breast cancer in human subjects (including dense breast tissues) by providing physiological information (e.g. oxy- and deoxy- hemoglobin concentration). At the Optical Imaging Laboratory, a hand-held optical imager has been developed which employs a breast contourable probe head to perform simultaneous illumination and detection of large surfaces towards near real-time imaging of human breast cancer. Gen-1 and gen-2 versions of the handheld optical imager have been developed and previously demonstrated imaging in tissue phantoms and healthy human subjects. Herein, the hand-held optical imagers are applied towards in vivo imaging of breast cancer subjects in an attempt to determine the ability of the imager to detect breast tumors. Five female human subjects (ages 51-74) diagnosed with breast cancer were imaged with the gen-1 optical imager prior to surgical intervention. One of the subjects was also imaged with the gen-2 optical imager. Both imagers use 785 nm laser diode sources and ICCD camera detectors to generate 2D surfaces maps of total hemoglobin absorption. The subjects lay in supine position and images were collected at various locations on both the ipsilateral (tumor-containing) and contralateral (non-tumor containing) breasts. The optical images (2D surface maps of optical absorption due to total hemoglobin concentration) show regions of higher intensity at the tumor location, which is indicative of increased vasculature and higher blood content due to the presence of the tumor. Additionally, a preliminary result indicates the potential to image lymphatic spread. This study demonstrates the potential of the hand-held optical devices to noninvasively image breast cancer in human subjects.
| S-EPMC4922423 | biostudies-literature
Project description:Successful single-cell isolation is a primary step for subsequent chemical and biological analyses of single cells. Conventional single-cell isolation methods often encounter operational complexity, limited efficiency, deterioration of cell viability, incompetence in the isolation of a single-cell into nanoliter liquid, and/or inability to select single adherent cells with specific phenotypes. Here, we develop a hand-held single-cell pipet (hSCP) that is rapid, operationally simple, highly efficient, and inexpensive for unbiased isolation of single viable suspended cells directly from submicroliter cell suspensions into nanoliter droplets without the assistance of any additional equipment. An integrated SCP (iSCP) has also been developed for selective isolation of single suspended and adherent cells according to the fluorescence imaging and morphological features. The isolated single cells can be conveniently transferred into standard 96-/384-well plates, Petri dishes, or vials for cloning, PCR, and other single-cell biochemical assays.
| S-EPMC4133013 | biostudies-literature
Project description:Purpose:To investigate feasibility and reliability of 3-dimensional full circumpapillary retinal nerve fiber layer (cpRNFL) analysis in children, with and without glaucoma, without the use of sedation and to recommend a protocol for hand-held optical coherence tomography use. Methods:A cohort of pediatric glaucoma patients and normal children were imaged with hand-held optical coherence tomography to assess the feasibility of obtaining full cpRNFL. Two consecutive scans were acquired in a smaller sample to investigate test-retest repeatability and interassessor reproducibility. The cpRNFL thickness was assessed in four quadrants, at several visual angles from the optic nerve center. Results:Scanning was attempted in both eyes of 90 children with pediatric glaucoma and 180 controls to investigate feasibility (mean age, 6.98 ± 4.42 years). Scanning was not possible in 68 eyes of glaucoma children mainly owing to nystagmus, unclear optical media, or high refractive errors. Where three-dimensional imaging was possible, success at obtaining full cpRNFL was 67% in children with glaucoma and 89% for controls. Seventeen children with pediatric glaucoma and 34 controls contributed to reliability analysis (mean age, 6.3 ± 3.63 years). For repeatability intraclass correlation coefficients across quadrants ranged from 0.63 to 0.82 at 4° and improved to 0.88 to 0.94 at 6°. Intraclass correlation coefficients for reproducibility were also highest at 6° (>0.97 across all quadrants). Conclusions:We demonstrate that acquisition and measurement of cpRNFL thickness values using 3-dimensional hand-held optical coherence tomography volumes in awake children is both feasible and reliable and is optimal at 6° from optic nerve center. Translational Relevance:Our recommended protocol provides guidance on how pediatric optic nerve pathologies are managed by clinicians.
| S-EPMC7414610 | biostudies-literature
Project description:Enamel proteins form a scaffold for growing hydroxyapatite crystals during enamel formation. They are then almost completely degraded during enamel maturation, resulting in a protein content of only 1% (w/v) in mature enamel. Nevertheless, this small amount of remaining proteins has important effects on the mechanical and structural properties of enamel and on the electrostatic properties of its surface. To analyze how enamel proteins affect tooth erosion, human enamel specimens were deproteinated. Surface microhardness (SMH), surface reflection intensity (SRI) and calcium release of both deproteinated and control specimens were monitored while continuously eroding them. The deproteination itself already reduced the initial SMH and SRI of the enamel significantly (p < 0.001 and p < 0.01). During the course of erosion, the progression of all three evaluated parameters differed significantly between the two groups (p < 0.001 for each). The deproteinated enamel lost its SMH and SRI faster, and released more calcium than the control group, but these differences were only significant at later stages of erosion, where not only surface softening but surface loss can be observed. We conclude that enamel proteins have a significant effect on erosion, protecting the enamel and slowing down the progression of erosion when irreversible surface loss starts to occur.
| S-EPMC4606565 | biostudies-other
Project description:Photocrosslinkable polyanhydrides that undergo surface erosion are suitable materials for controlled-release drug delivery systems. Investigating the impact of different parameters on their erosion behavior is essential before use in drug delivery systems. Although their synthesis is well-established, parameters that may substantially affect the erosion of thiol-ene polyanhydrides including temperature and pH of the media, the geometry of the polymers, and the media shaking rate (the convective force for the polymer erosion), have not yet been studied. This study explores the effects of different environmental and geometric parameters on mass loss (erosion) profiles of polyanhydrides synthesized by thiol-ene photopolymerization. A comparative study on several release kinetic models fitting is also described for a better understanding of the polymer erosion behavior. The results demonstrated that although the temperature was the only parameter that affected the induction period substantially, the mass-loss rate was influenced by the polymer composition, tablet geometry, temperature, pH, and mass transfer (shaking) rate. With regard to geometrical parameters, polymers with the same surface area to volume ratios showed similar mass loss trends despite their various volumes and surface areas. The mass loss of polyanhydride tablets with more complicated geometries than a simple slab was shown to be non-linear, and the kinetic model study indicated the dominant surface erosion mechanism. The results of this study allow for designing and manufacturing efficient delivery systems with a high-predictable drug release required in precision medicine using surface-erodible polyanhydrides.
| S-EPMC7285269 | biostudies-literature
Project description:ObjectivesTo determine if Sa roughness data from measuring one central location of unpolished and polished enamel were representative of the overall surfaces before and after erosion.MethodsTwenty human enamel sections (4x4 mm) were embedded in bis-acryl composite and randomised to either a native or polishing enamel preparation protocol. Enamel samples were subjected to an acid challenge (15 minutes 100 mL orange juice, pH 3.2, titratable acidity 41.3mmol OH/L, 62.5 rpm agitation, repeated for three cycles). Median (IQR) surface roughness [Sa] was measured at baseline and after erosion from both a centralised cluster and four peripheral clusters. Within each cluster, five smaller areas (0.04 mm2) provided the Sa roughness data.ResultsFor both unpolished and polished enamel samples there were no significant differences between measuring one central cluster or four peripheral clusters, before and after erosion. For unpolished enamel the single central cluster had a median (IQR) Sa roughness of 1.45 (2.58) μm and the four peripheral clusters had a median (IQR) of 1.32 (4.86) μm before erosion; after erosion there were statistically significant reductions to 0.38 (0.35) μm and 0.34 (0.49) μm respectively (p<0.0001). Polished enamel had a median (IQR) Sa roughness 0.04 (0.17) μm for the single central cluster and 0.05 (0.15) μm for the four peripheral clusters which statistically significantly increased after erosion to 0.27 (0.08) μm for both (p<0.0001).ConclusionMeasuring one central cluster of unpolished and polished enamel was representative of the overall enamel surface roughness, before and after erosion.
| S-EPMC5542659 | biostudies-literature
Project description:BackgroundUltrasound imaging devices are becoming popular in clinical and teaching settings, but there is no systematic information on their use in medical education. We conducted a systematic review of hand-held ultrasound (HHU) devices in undergraduate medical education to delineate their role, significance, and limitations.MethodsWe searched Cochrane, PubMed, Embase, and Medline using the strategy: [(Hand-held OR Portable OR Pocket OR "Point of Care Systems") AND Ultrasound] AND (Education OR Training OR Undergraduate OR "Medical Students" OR "Medical School"). We retained 12 articles focusing on undergraduate medical education. We summarised the patterns of HHU use, pooled and estimated sensitivity, and specificity of HHU for detection of left ventricular dysfunction.ResultsFeatures reported were heterogeneous: training time (1-25 hours), number of students involved (1-an entire cohort), number of subjects scanned (27-211), and type of learning (self-directed vs. traditional lectures + hands-on sessions). Most studies reported cardiac HHU examinations, but other anatomical areas were examined, e.g. abdomen and thyroid. Pooled sensitivity 0.88 [95% confidence interval (CI) 0.83-0.92] and specificity 0.86 (95% CI 0.81-0.90) were high for the detection of left ventricular systolic dysfunction by students.ConclusionData on HHU devices in medical education are scarce and incomplete, but following training students can achieve high diagnostic accuracy, albeit in a limited number of (mainly cardiac) pathologies. There is no consensus on protocols best-suited to the educational needs of medical students, nor data on long-term impact, decay in proficiency or on the financial implications of deploying HHU in this setting.
| S-EPMC5658292 | biostudies-literature
Project description:ObjectiveTo investigate the relationship between cystoid macular oedema (CMO) measured in preterm infants using hand-held spectral domain optical coherence tomography (HH SD-OCT), with gestational age at birth (GA), birthweight (BW), diagnosis of retinopathy of prematurity (ROP) and the presence or absence of the external limiting membrane (ELM).MethodsWe conducted a prospective mixed cross-sectional/longitudinal observational study of 112 participants (23 to 36 weeks GA; n = 25 with, and n = 87 without, CMO). Retinal images were acquired using 344 HH SD-OCT (n = 66 with and n = 278 without, CMO) between 31 to 44 weeks postmenstrual age (PMA). CMO type ('fovea' and 'dome') was measured using thickness, width, area and peak.ResultsCMO was observed in 22.9% of preterm infants, and 19.2% of images. The mean values for thickness, width, area and peak of 'dome' CMO were 128.47 µm (SD +/- 34.23), 3624.45 µm (SD +/- 1323.03), 0.49 mm2 (SD +/- 0.28) and 279.81 µm (SD +/- 13.57) respectively. The mean values for thickness, width, area and peak of 'fovea' CMO were 64.37 µm (SD +/- 17.11), 2226.28 µm (SD +/- 1123.82), 0.16 mm2 (SD +/- 0.11) and 95.03 µm (SD +/- 26.99) respectively. Thickness, area width and peak were significantly greater for 'dome CMO compared with 'fovea' CMO (P < 0.0001 for thickness, area and peak; P < 0.01 for width). Area and width significantly decreased with PMA for 'dome' and 'fovea' CMO (p = 0.0028; p < 0.001 respectively). No association was found between the presence of ROP and the detection of CMO or detection of CMO with absence of ELM.ConclusionsHH -OCT in preterm infants demonstrates that the severity of CMO appearance improves each week for both fovea and dome CMO.
| S-EPMC10516860 | biostudies-literature
Project description:In enamel formation, the deposition of minerals as crystallites starts when the mineralization front first forms at the start of the secretory stage. During maturation, the enamel layer accumulates significant amounts of new mineral as the crystallites grow in volume. Inversely related to mineral gain is loss of protein and water from the forming enamel. Both ameloblastin (Ambn) and enamelin are essential components for formation of a functional enamel layer. The aim of this study was to quantify the proportion of mineral and non-mineral material present in developing enamel relative to Ambn concentration using Ambn mutant mice mated with others overexpressing full-length Ambn from the mouse amelogenin promoter at lower (+), similar (++) or higher (+++) concentration than normal. Mandibular incisors (age: 7 weeks, n?=?8) were imaged by micro-computed tomography and the enamel was analyzed from the apical region to the incisal edge in sequential 1.0?mm volumes of interest. Mineral density was determined using a series of hydroxyapatite (HA) phantoms to calibrate enamel density measurements. At the site where the mandibular incisor emerged into the oral cavity, the enamel volume, mineral weight, and mineral density were reduced when Tg Ambn was expressed at lower or higher levels than normal. While in wild-type the % mineral was >95%, it was negligible in Ambn-/-, 22.3% in Ambn-/-, Tg(+), 75.4% in Ambn-/-, Tg(++), and 45.2% in Ambn-/-, Tg(+++). These results document that the deposition of mineral and removal of non-mineral components are both very sensitive to expressed Ambn concentrations.
| S-EPMC4471956 | biostudies-literature