Surfactant-assisted Nanocasting Route for Synthesis of Highly Ordered Mesoporous Graphitic Carbon and Its Application in CO2 Adsorption.
Ontology highlight
ABSTRACT:
SUBMITTER: Wang Y
PROVIDER: S-EPMC4879549 | biostudies-other | 2016
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The post-synthesis procedure for cyclic amine (morpholine and 1-methylpiperazine) modified mesoporous MCM-48 and SBA-15 silicas was developed. The procedure for preparation of the modified mesoporous materials does not affect the structural characteristics of the initial mesoporous silicas strongly. The initial and modified materials were characterized by XRD, N2 physisorption, thermal analysis, and solid-state NMR. The CO2 adsorption of the obtained materials was tested under dynamic and equilibrium conditions. The NMR data revealed the formation of different CO2 adsorbed forms. The materials exhibited high CO2 absorption capacity lying above the benchmark value of 2 mmol/g and stretching out to the outstanding 4.4 mmol/g in the case of 1-methylpiperazin modified MCM-48. The materials are reusable, and their CO2 adsorption capacities are slightly lower in three adsorption/desorption cycles.
| S-EPMC8621056 | biostudies-literature
Project description:Bicontinuous particle-stabilized emulsions (bijels) are networks of interpenetrating oil/water channels with applications in catalysis, tissue engineering, and energy storage. Bijels can be generated by arresting solvent transfer induced phase separation (STrIPS) via interfacial jamming of nanoparticles. However, until now, STrIPS bijels have only been formed with silica nanoparticles of low surface charge densities, limiting their potential applications in catalysis and fluid transport. Here, we show how strongly charged silica nanoparticles can stabilize bijels. To this end, we carry out a systematic study employing dynamic light scattering, zeta potential, acid/base titrations, turbidimetry, surface tension, and confocal microscopy. We find that moderating the adsorption of oppositely charged surfactants on the particles is crucial to facilitate particle dispersibility in the bijel casting mixture and bijel stabilization. Our results potentially introduce a general understanding for bijel fabrication with different inorganic nanoparticle materials of variable charge density.
| S-EPMC7295363 | biostudies-literature
Project description:Creating highly active and stable metal catalysts is a persistent goal in the field of heterogeneous catalysis. However, a real catalyst can rarely achieve both of these qualities simultaneously due to limitations in the design of the active site and support. One method to circumvent this problem is to fabricate firmly attached metal species onto the voids of a mesoporous support formed simultaneously. In this study, we developed a new type of ruthenium catalyst that was firmly confined by ordered mesoporous carbons through the fabrication of a cubic Ia3d chitosan-ruthenium-silica mesophase before pyrolysis and silica removal. This facile method generates fine ruthenium nanoparticles (ca. 1.7?nm) that are homogeneously dispersed on a mesoporous carbonaceous framework. This ruthenium catalyst can be recycled 22 times without any loss of reactivity, showing the highest stability of any metal catalysts; this catalyst displays a high activity (23.3?mol(LA)h(-1)g(metal)(-1)) during the catalytic hydrogenation of levulinic acid (LA) when the metal loading is 6.1?wt%. Even at an ultralow loading (0.3?wt%), this catalyst still outperforms the most active known Ru/C catalyst. This work reveals new possibilities for designing and fabricating highly stable and active metal catalysts by creating metal sites and mesoporous supports simultaneously.
| S-EPMC3971394 | biostudies-literature
Project description:Mesoporous carbons were synthesized via both soft and hard template methods and compared to a commercial powder activated carbon (PAC) for the adsorption ability of bisphenol-A (BPA) from an aqueous solution. The commercial PAC had a BET-surface of 1027 m²/g with fine pores of 3 nm and less. The hard templated carbon (CMK-3) material had an even higher BET-surface of 1420 m²/g with an average pore size of 4 nm. The soft templated carbon (SMC) reached a BET-surface of 476 m²/g and a pore size of 7 nm. The maximum observed adsorption capacity (qmax) of CMK-3 was the highest with 474 mg/g, compared to 290 mg/g for PAC and 154 mg/g for SMC. The difference in adsorption capacities was attributed to the specific surface area and hydrophobicity of the adsorbent. The microporous PAC showed the slowest adsorption, while the ordered mesopores of SMC and CMK-3 enhanced the BPA diffusion into the adsorbent. This difference in adsorption kinetics is caused by the increase in pore diameter. However, CMK-3 with an open geometry consisting of interlinked nanorods allows for even faster intraparticle diffusion.
| S-EPMC5507042 | biostudies-other
Project description:In situ small-angle X-ray scattering was used to identify structural changes during thermal treatment of an ordered mesoporous carbon precursor material, synthesized via direct soft templating, to remove Pluronic F127 surfactant from a resorcinol–formaldehyde frame. In situ small-angle X-ray scattering (SAXS) was employed to identify critical parameters during thermal treatment for template removal of an ordered mesoporous carbon precursor synthesized via a direct soft-templating route. The structural parameters obtained from the SAXS data as a function of time were the lattice parameter of the 2D hexagonal structure, the diameter of the cylindrical mesostructures and a power-law exponent characterizing the interface roughness. Moreover, detailed information on contrast changes and pore lattice order was obtained from analysis of the integrated SAXS intensity of the Bragg and diffuse scattering separately. Five characteristic regions during heat treatment were identified and discussed regarding the underlying dominant processes. The influence of temperature and O2/N2 ratio on the final structure was analyzed, and parameter ranges were identified for an optimized template removal without strongly affecting the matrix. The results indicate that the final structure and controllability of the process are optimum for temperatures between 260 and 300°C with a gas flow containing 2 mol% of O2.
| S-EPMC10241053 | biostudies-literature
Project description:Highly ordered vertically grown zinc oxide nanorods (ZnO NRs) were synthesized on ZnO-coated SiO2/Si substrate using zinc acetylacetonate hydrate as a precursor via a simple hydrothermal method at 85 °C. We used 0.05 M of ZnO solution to facilitate the growth of ZnO NRs and the immersion time was varied from 0.5 to 4 h. The atomic force microscopy revealed the surface roughness of ZnO seed layer used to grow the ZnO NRs. The morphology of vertically grown ZnO NRs was observed by field emission scanning electron microscopy. X-ray diffraction examination and transmission electron microscopy confirmed that the structure of highly ordered ZnO NRs was crystalline with a strong (002) peak corresponded to ZnO hexagonal wurtzite structure. The growth of highly ordered ZnO NRs was favorable due to the continuous supply of Zn2+ ions and chelating agents properties obtained from the acetylacetonate-derived precursor during the synthesis. Two-point probe current-voltage measurement and UV-vis spectroscopy of the ZnO NRs indicated a resistivity and optical bandgap value of 0.44 ?.cm and 3.35 eV, respectively. The photoluminescence spectrum showed a broad peak centered at 623 nm in the visible region corresponded to the oxygen vacancies from the ZnO NRs. This study demonstrates that acetylacetonate-derived precursors can be used for the production of ZnO NRs-based devices with a potential application in biosensors.
| S-EPMC7084973 | biostudies-literature
Project description:Highly efficient simultaneous removal of atrazine and Cu(II) was accomplished using synthesized polyacrylic acid-functionalized magnetic ordered mesoporous carbon (P-MMC) as compared to magnetic ordered mesoporous carbon (MMC) and ordered mesoporous carbon (OMC). The mutual effects and interactive mechanism of their adsorption onto P-MMC were investigated systematically by binary, preloading and thermodynamic adsorption procedures. In both binary and preloading systems, the adsorption of atrazine was inhibited to some extent by the presence of Cu(II) because of selective recognition and direct competition, but the presence of atrazine had negligible effect on Cu(II) desorption. With the coexistence of humic acid (0-20?mg?L-1), both atrazine and Cu(II) sorption increased slightly in sole and binary systems. With the concentration of coexisting NaCl increasing from 0 to 100?mM, the adsorption capacity for Cu(II) slightly decreased, but as for atrazine adsorption, it decreased at first, and then increased slightly in sole and binary systems. P-MMC was applied to treat real environmental samples, and the sorption capacities for atrazine and Cu(II) in real samples were all more than 91.47% and 96.43% of those in lab ultrapure water, respectively. Finally, comprehensively considering the relatively good renewability and the superior behavior in the application to real water samples, P-MMC has potential in removal of atrazine, Cu(II) and possibly other persistent organic pollutants from wastewater.
| S-EPMC5333147 | biostudies-literature
Project description:To eliminate nitrogen oxides (NOx), a series of highly ordered mesoporous WO3(?)-CeO2 nanomaterials (? represents the mole ratio of W/Ce) were synthesized by using KIT-6 as a hard template, which was used for selective catalytic reduction (SCR) to remove NOx with NH3 at low temperatures. Moreover, the nanomaterials were characterized by TEM, XRD, Raman, XPS, BET, H2-TPR, NH3-TPD and in situ DRIFTS. It can be found that all of the prepared mesoporous WO3(?)-CeO2 (? = 0, 0.5, 0.75, 1 and 1.25) showed highly ordered mesoporous channels. Furthermore, mesoporous WO3(1)-CeO2 exhibited the best removal efficiency of NOx, and its NOx conversion ratio could reach 100% from 225 ° C to 350 ° C with a gas hourly space velocity of 30 000 h-1, which was due to higher Ce3+ concentrations, abundant active surface oxygen species and Lewis acid sites based on XPS, H2-TPR, NH3-TPD and in situ DRIFTS. In addition, several key performance parameters of mesoporous WO3(1)-CeO2, such as superior water resistance, better alkali metal resistance, higher thermal stability and N2 selectivity, were systematically studied, indicating that the synthesized mesoporous WO3(1)-CeO2 has great potential for industrial applications.
| S-EPMC5505671 | biostudies-literature
Project description:Alumina materials have widely been used in industrial fields, such as catalysis and adsorption. However, due to the fast sol-gel process and complicated crystalline-phase transformation, the synthesis of alumina materials with both highly ordered mesostructures and crystallized frameworks remains a great challenge. Herein, we report a novel vesicle-aggregation-assembly strategy to prepare highly ordered mesoporous ?-alumina microspheres with unique shifted double-diamond networks for the first time, by using diblock copolymer poly(ethylene oxide)-b-poly(methyl methacrylate) (PEO-b-PMMA) as a template and aluminum isopropoxide as a precursor in a tetrahydrofuran (THF)/hydrochloric acid binary solvent. During the gradual evaporation of THF and H2O, the as-made Al3+-based gel/PEO-b-PMMA composites can be obtained through a co-assembly process based on the hydrogen bonding interaction between hydroxyl groups of alumina oligomers and PEO segments of the diblock copolymers. The formed composites exhibit a spherical morphology with a wide size distribution (diameter size 1-12 ?m). Furthermore, these composite microspheres possess an inverse bicontinuous cubic mesostructure (double diamond, Pn3[combining macron]m) with Al3+-based gel buried in the PEO-b-PMMA matrix in the form of two intertwined but disconnected networks. After a simple calcination at 900 °C in air, the structure of the resultant mesoporous alumina changes to a relatively low symmetry (shifted double diamond, Fd3[combining macron]m), ascribed to the shifting of the two alumina networks due to loss of the templates. Meanwhile, the unit cell size of the alumina mesostructure decreases from ?131 to ?95 nm. The obtained ordered mesoporous alumina products retain the spherical morphology and possess ultra-large mesopores (?72.8 nm), columnar frameworks composed of ?-alumina nanocrystalline particles (crystal size of ?15 nm) and high thermal stability (up to 900 °C). As a support of Au nanoparticles, the formed Au/mesoporous ?-alumina composite catalysts have been used in the catalytic reduction of 4-nitrophenol with a high kinetic constant k of 0.0888 min-1, implying promising potential as a catalyst support.
| S-EPMC6182608 | biostudies-literature
Project description:We report that transparent mesostructured silica/gold nanocomposite materials with an interpore distance of 4.1 nm, as-synthesized from a templated sol-gel synthesis method using discotic trinuclear gold(I) pyrazolate complex, were successfully utilized for the fabrication of thin film mesoporous silica nanocomposites containing gold nanoparticles. The material exhibited a highly ordered hexagonal structure when subjected to a thermal hydrogen reduction treatment at 210 °C. In contrast, when the material was subjected to calcination as a heat treatment from 190 to 450 °C, the thin film nanocomposites showed an intense d 100 X-ray diffraction peak. Moreover, gold nanoparticles inside the thin film nanocomposites were confirmed by the presence of the d 111 diffraction peak at 2θ = 38.2°, a surface plasmon resonance peak between 500-580 nm, and the spherical shape observed in the transmission electron microscope images, as well as the visual change in color from pink to purple. Interestingly, by simply dipping the material into a reaction solution of 4-nitrophenol at room temperature, the highly ordered structure of the as-fabricated silica/gold nanoparticle thin film composite after thermal hydrogen reduction at 210 °C resulted in an improved catalytic activity for the reduction of 4-nitrophenol to 4-aminophenol compared to the material calcined at 250 °C. Such catalytic activity is due to the presence of gold nanoparticles of smaller size in the silicate channels of the highly ordered mesoporous film nanocomposites.
| S-EPMC6633902 | biostudies-literature