On the Injection Molding Processing Parameters of HDPE-TiO₂ Nanocomposites.
Ontology highlight
ABSTRACT:
SUBMITTER: Mourad AI
PROVIDER: S-EPMC5344589 | biostudies-other | 2017 Jan
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO₂ nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO₂), barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young's modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L₉ orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO₂, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA) has also been applied to identify the most significant factor, and the percentage of TiO₂ nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO₂ nanocomposites fabricated through the injection molding process.
| S-EPMC5512532 | biostudies-other
Project description:Halloysite nanotubes-thermoplastic polyurethane (HNTs-TPU) nanocomposites are attractive products due to increasing demands for specialized materials. This study attempts to optimize the parameters for injection just before marketing. The study shows the importance of the preparation of the samples and how well these parameters play their roles in the injection. The control parameters for injection are carefully determined to examine the mechanical properties and the density of the HNTs-TPU nanocomposites. Three types of modified HNTs were used as untreated HNTs (uHNTs), sulfuric acid treated (aHNTs) and a combined treatment of polyvinyl alcohol (PVA)-sodium dodecyl sulfate (SDS)-malonic acid (MA) (treatment (mHNTs)). It was found that mHNTs have the most influential effect of producing HNTs-TPU nanocomposites with the best qualities. One possible reason for this extraordinary result is the effect of SDS as a disperser and MA as a crosslinker between HNTs and PVA. For the highest tensile strength, the control parameters are demonstrated at 150 °C (injection temperature), 8 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). Meanwhile, the optimized combination of the levels for all six control parameters that provide the highest Young's modulus and highest density was found to be 150 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 3 wt % (HNTs loading) and mHNT (HNTs type). For the best tensile strain, the six control parameters are found to be 160 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). For the highest hardness, the best parameters are 140 °C (injection temperature), 6 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). The analyses are carried out by coordinating Taguchi and ANOVA approaches. Seemingly, mHNTs has shown its very important role in the resulting product.
| S-EPMC5457251 | biostudies-other
Project description:Transparent ceramics like magnesium aluminate spinel (MAS) are considered the next step in material evolution showing unmatched mechanical, chemical and physical resistance combined with high optical transparency. Unfortunately, transparent ceramics are notoriously difficult to shape, especially on the microscale. Therefore, a thermoplastic MAS nanocomposite is developed that can be shaped by polymer injection molding at high speed and precision. The nanocomposite is converted to dense MAS by debinding, pre-sintering, and hot isostatic pressing yielding transparent ceramics with high optical transmission up to 84 % and high mechanical strength. A transparent macroscopic MAS components with wall thicknesses up to 4 mm as well as microstructured components with single micrometer resolution are shown. This work makes transparent MAS ceramics accessible to modern high-throughput polymer processing techniques for fast and cost-efficient manufacturing of macroscopic and microstructured components enabling a plethora of potential applications from optics and photonics, medicine to scratch and break-resistant transparent windows for consumer electronics.
| S-EPMC9631057 | biostudies-literature
Project description:While organic photovoltaics are accessing specific application sectors taking advantage of their unique properties, it is important to identify as many differentiators as possible to expand the market penetration and consolidation of this technology. In this work, for the first time, the large-scale fabrication of organic photovoltaic modules embedded into structural plastic parts through industrial injection molding is demonstrated. Thermoplastic polyurethane is chosen as the injected material to show that this additional processing step can yield flexible, lightweight photovoltaic modules with enhanced device robustness and virtually unchanged performance. The critical optomechanical and physico-chemical material properties, as well as the plastic processing parameters to enable in-mold plastic solar cells with improved performance and stability, are discussed and provided with perspective.
| S-EPMC10646225 | biostudies-literature
Project description:Nanopattern replication of complex structures by plastic injection is a challenge that requires simulations to define the right processing parameters. Previous work managed to simulate replication for single cavities in 2D and 3D, showing high performance requirements of CPU to simulate periodic trenches in 2D. This paper presents two ways to approach the simulation of replication of complex 3D hydrophobic surfaces. The first approach is based on previous CFD Ansys Fluent and compared to FE based CFD Polyflow software for the analysis of laminar flows typical in polymer processing and glass forming as well as other applications. The results showed that Polyflow was able to reduce computing time from 72 h to only 5 min as desired in the project. Furthermore, simulations carried out with Polyflow showed that higher injection and mold temperature lead to better replication of hydrophobicity in agreement with the experiments. Polyflow simulations are proved to be a good tool to define process parameters such as temperature and cycle times for nanopattern replication.
| S-EPMC8272097 | biostudies-literature
Project description:Flexible polymers such as poly dimethyl siloxane (PDMS) can be patterned at the micro- and nanoscale by casting, for a variety of applications. This replication-based fabrication process is relatively cheap and fast, yet injection molding offers an even faster and cheaper alternative to PDMS casting, provided thermoplastic polymers with similar mechanical properties can be used. In this paper, a thermoplastic polyurethane is evaluated for its patterning ability with an aim to forming the type of flexible structures used to measure and modulate the contractile forces of cells in tissue engineering experiments. The successful replication of grating structures is demonstrated with feature sizes as low as 100 nm and an analysis of certain processing conditions that facilitate and enhance the accuracy of this replication is presented. The results are benchmarked against an optical storage media grade polycarbonate.
| S-EPMC6563430 | biostudies-literature
Project description:The waste generated by single-use plastics is often non-recyclable and non-biodegradable, inevitably ending up in our landfills, ecosystems, and food chain. Through the introduction of biodegradable polymers as substitutes for common plastics, we can decrease our impact on the planet. In this study, we evaluate the changes in mechanical and thermal properties of polyhydroxybutyrate-based composites with various additives: Microspheres, carbon fibers or polyethylene glycol (2000, 10,000, and 20,000 MW). The mixtures were injection molded using an in-house mold attached to a commercial extruder. The resulting samples were characterized using microscopy and a series of spectroscopic, thermal, and mechanical techniques. We have shown that the addition of carbon fibers and microspheres had minimal impact on thermal stability, whereas polyethylene glycol showed slight improvements at higher molecular weights. All of the composite samples showed a decrease in hardness and compressibility. The findings described in this study will improve our understanding of polyhydroxybutyrate-based composites prepared by injection molding, enabling advancements in integrating biodegradable plastics into everyday products.
| S-EPMC8704503 | biostudies-literature
Project description:High-density polyethylene (HDPE)-based and ultra-high molecular weight polyethylene (UHMWPE)-based composites with carbonaceous reinforcements are being widely investigated for biomedical applications. The enhancement of material properties critically depends on the nature, amount and compatibility of the reinforcement with the polymeric matrix. To this end, this study demonstrates the efficacy of a 'dual' hybrid approach of incorporating modified inorganic nanofiller into an optimized polyethylene blend. In particular, a unique synthesis strategy was adopted to design a covalently bonded maleated polyethylene (mPE) grafted modified graphene oxide (mGO) hybrid nanocomposite. In this scheme, polyethyleneimine (PEI) was initially attached onto GO to synthesize amine functionalized GO (GO-PEI). This is followed by mPE grafting, resulting in mGO. Melt-extrusion together with injection moulding of a polymer mix (60% HDPE-40% UHMWPE) with different proportions (less than or equal to 3 wt%) of surface functionalized GO was conducted to develop nanocomposites of different sizes and shapes. When compared with unreinforced PE blend, the nanocomposites with 1 wt% mGO exhibited an increase in ultimate tensile strength by 120% (up to 65 MPa) and elastic modulus by 40% (up to 908 MPa). The uniform dispersion of modified GO nanofillers, confirmed using X-ray micro-computed tomography and transmission electron microscopy, facilitated effective interfacial adhesion and compatibility with the hybrid polymer matrix. The variation in mechanical properties with GO/mGO addition to PE blend was critically discussed in reference to the structural modification of GO, crystallinity and nature of dispersion of fillers. Importantly, the nanocomposites support the attachment and proliferation of C2C12 murine myoblast cells over 3 days in culture in a statistically insignificant manner with respect to polymer blends without any nanofiller. Taken together, the experimental results suggest that HDPE/UHMWPE/mGO is a promising biomaterial for bone tissue engineering applications.
| S-EPMC6364642 | biostudies-literature
Project description:Microscale cell-based assays have demonstrated unique capabilities in reproducing important cellular behaviors for diagnostics and basic biological research. As these assays move beyond the prototyping stage and into biological and clinical research environments, there is a need to produce microscale culture platforms more rapidly, cost-effectively, and reproducibly. 'Rapid' injection molding is poised to meet this need as it enables some of the benefits of traditional high volume injection molding at a fraction of the cost. However, rapid injection molding has limitations due to the material and methods used for mold fabrication. Here, we characterize advantages and limitations of rapid injection molding for microfluidic device fabrication through measurement of key features for cell culture applications including channel geometry, feature consistency, floor thickness, and surface polishing. We demonstrate phase contrast and fluorescence imaging of cells grown in rapid injection molded devices and provide design recommendations to successfully utilize rapid injection molding methods for microscale cell-based assay development in academic laboratory settings.
| S-EPMC5790604 | biostudies-literature
Project description:Patterning of micro- and nanoscale topologies and surface properties of polymer devices is of particular importance for a broad range of life science applications, including cell-adhesion assays and highly sensitive bioassays. The manufacturing of such devices necessitates cumbersome multiple-step fabrication procedures and results in surface properties which degrade over time. This critically hinders their wide-spread dissemination. Here, we simultaneously mold and surface energy pattern microstructures in off-stoichiometric thiol-ene by area-selective monomer self-assembly in a rapid micro-reaction injection molding cycle. We replicated arrays of 1,843,650 hydrophilic-in-hydrophobic femtolitre-wells with long-term stable surface properties and magnetically trapped beads with 75% and 87.2% efficiency in single- and multiple-seeding events, respectively. These results form the basis for ultrasensitive digital biosensors, specifically, and for the fabrication of medical devices and life science research tools, generally.
| S-EPMC6545322 | biostudies-literature