Degradation of 2,4-Dichlorophenoxyacetic Acid (2,4-D) by Novel Photocatalytic Material of Tourmaline-Coated TiO₂ Nanoparticles: Kinetic Study and Model.
Ontology highlight
ABSTRACT:
SUBMITTER: Bian X
PROVIDER: S-EPMC5452311 | biostudies-other | 2013 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Diclofenac (DCF) is one of the most detected pharmaceuticals in environmental water matrices and is known to be recalcitrant to conventional wastewater treatment plants. In this study, degradation of DCF was performed in water by photolysis and photocatalysis using a new synthetized photocatalyst based on hydroxyapatite and TiO₂ (HApTi). A degradation of 95% of the target compound was achieved in 24 h by a photocatalytic treatment employing the HApTi catalyst in comparison to only 60% removal by the photolytic process. The investigation of photo-transformation products was performed by means of UPLC-QTOF/MS/MS, and for 14 detected compounds in samples collected during treatment with HApTi, the chemical structure was proposed. The determination of transformation product (TP) toxicity was performed by using different assays: Daphnia magna acute toxicity test, Toxi-ChromoTest, and Lactuca sativa and Solanum lycopersicum germination inhibition test. Overall, the toxicity of the samples obtained from the photocatalytic experiment with HApTi decreased at the end of the treatment, showing the potential applicability of the catalyst for the removal of diclofenac and the detoxification of water matrices.
| S-EPMC6164299 | biostudies-other
Project description:Nanosized titanium oxide (TiO2) material is a promising photocatalyst for the degradation of organic pollutants, whereas the difficulty of its recycling hinders its practical application. Herein, we reported the preparation of a novel titanium oxide/polysulfone (TiNPs/PSF) composite hollow microspheres by the combination of Pickering emulsification and the solvent evaporation technique and their application for the photodegradation of methyl blue (MB). P25 TiO2 nanoparticles dispersed on the surface of PSF microspheres. The porosity, density and photoactivity of the TiNPs/PSF composite microsphere are influenced by the TiO2 loading amount. The composite microsphere showed good methyl blue (MB) removal ability. Compared with TiO2 P25, and PSF, a much higher MB adsorption speed was observed for TiNPs/PSF microspheres benefited from their porous structure and the electrostatic attractions between the MB+ and the negatively charged PSF materials, and showed good degradation efficiency. For TiNPs/PSF composite microsphere with density close to 1, a 100% MB removal (10 mg L-1) within 120 min at a catalyst loading of 2.5 g L-1 can be obtained under both stirring and static condition, due to well dispersing of TiO2 particles on the microsphere surface and its stable suspending in water. For the non-suspended TiNPs/PSF composite microsphere with density bigger than 1, the 100% MB removal can be only obtained under stirring condition. The removal efficiency of MB for the composite microspheres retained 96.5%, even after 20 cycles. Moreover, this composite microsphere also showed high MB removal ability at acidic condition. The high catalysis efficiency, excellent reusability and good stability make this kind of TiNPs/PSF composite microsphere a promising photocatalyst for the water organic pollution treatment.
| S-EPMC7865213 | biostudies-literature
Project description:Numerous reports have elucidated that TiO2 nanoparticles (TiO2-NPs) exhibit respectable photocatalytic degradation capacities due to their high specific surface areas. However, the current recovery process leads to a loss of TiO2-NPs; therefore, there is a need to immobilize TiO2-NPs on the substrate used. Herein, TiO2-coated yttria-stabilized zirconia/silica nanofiber (TiO2-coated YSZ/silica NF) was prepared by coating TiO2 on the surface of YSZ/silica NF using a sol-gel process. The TiO2 coating layer on the nanofiber surface improved the separation ability of the membrane as well as the photocatalytic degradation ability. The pore size of the TiO2-coated YSZ/silica NF membrane was less than that of the pristine YSZ/silica NF membrane, and it rejected over 99.6% of the 0.5 μm polymeric particles. In addition, the TiO2-coated YSZ/silica NF membrane showed excellent adsorption/degradation of humic acid (HA, 88.2%), methylene blue (MB, 92.4%), and tetracycline (TC, 99.5%). Six recycling tests were performed to evaluate the reusability of the TiO2-coated YSZ/silica NF membrane. The adsorption/degradation efficiency for HA, MB, and TC decreased by 3.7%, 2.8%, and 2.2%, respectively. We thus verified the high separation ability, excellent photocatalytic degradation ability, and excellent reusability of the TiO2-coated YSZ/silica NF membranes.
| S-EPMC7576826 | biostudies-literature
Project description:This study presents an experimental overview for the development of photocatalytic materials based on geopolymer binders as catalyst support matrices. Particularly, geopolymer matrices obtained from different solid precursors (fly ash and metakaolin), composite systems (siloxane-hybrid, foamed hybrid), and curing temperatures (room temperature and 60 °C) were investigated for the same photocatalyst content (i.e., 3% TiO₂ by weight of paste). The geopolymer matrices were previously designed for different applications, ranging from insulating (foam) to structural materials. The photocatalytic activity was evaluated as NO degradation in air, and the results were compared with an ordinary Portland cement reference. The studied matrices demonstrated highly variable photocatalytic performance depending on both matrix constituents and the curing temperature, with promising activity revealed by the geopolymers based on fly ash and metakaolin. Furthermore, microstructural features and titania dispersion in the matrices were assessed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDS) analyses. Particularly, EDS analyses of sample sections indicated segregation effects of titania in the surface layer, with consequent enhancement or depletion of the catalyst concentration in the active sample region, suggesting non-negligible transport phenomena during the curing process. The described results demonstrated that geopolymer binders can be interesting catalyst support matrices for the development of photocatalytic materials and indicated a large potential for the exploitation of their peculiar features.
| S-EPMC5456889 | biostudies-other
Project description:Special attention has recently been paid to surface-defective titanium dioxide and black TiO2 with advanced optical, electrical, and photocatalytic properties. Synthesis of these materials for photodegradation and mineralization of persistent organic pollutants in water, especially under visible radiation, presents interest from scientific and application points of view. Chemical reduction by heating a TiO2 and NaBH4 mixture at 350 °C successfully introduced Ti3+ defects and oxygen vacancies at the surface of TiO2, with an increase in the photocatalytic degradation of amoxicillin-an antibiotic that is present in wastewater due to its intense use in human and animal medicine. Three TiO2 samples were prepared at different annealing temperatures to control the ratio between anatase and rutile and were subjected to chemical reduction. Electron paramagnetic resonance investigations showed that the formation of surface Ti3+ defects in a high concentration occurred mainly in the anatase sample annealed at 400 °C, contributing to the bandgap reduction from 3.32 eV to 2.92 eV. The reduced band gap enhances visible light absorption and the efficiency of photocatalysis. The nanoparticles of ~90 m2/g specific surface area and 12 nm average size exhibit ~100% efficiency in the degradation of amoxicillin under simulated solar irradiation compared with pristine TiO2. Mineralization of amoxicillin and by-products was over 75% after 48 h irradiation for the anatase sample, where the Ti3+ defects were present in a higher concentration at the catalyst's surface.
| S-EPMC9330099 | biostudies-literature
Project description:Nanocomposites comprising nitrogen-doped TiO2 and reduced graphene oxide (N/TiO2/rGO), with different rGO loading qualities, were prepared by a cost-effective microwave-assisted synthesis method. The synthesized materials were broadly characterized by Raman spectroscopy, X-ray diffraction (XRD), infrared spectroscopy (FTIR), photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS), electron microscopy (SEM-EDS), and nitrogen adsorption/desorption isotherms. Anatase was the only crystalline phase observed for all synthesized materials. The rGO loading did not affect the morphological properties, but it positively influenced the photocatalytic activity of the nanocomposite materials, especially at low rGO loading. Photocatalysts were evaluated via the degradation of specific organic micropollutant (OMP) pharmaceuticals: ciprofloxacin (CIP), diclofenac (DCF), and salicylic acid (SA), under different radiation sources: ultraviolet A (UVA), solar light simulator (SLS), blue visible light (BVL) and cold visible light (CVL). CIP and SA were removed effectively via the synergy of adsorption and photocatalysis, while DCF degradation was achieved solely by photocatalysis. After implementing scavenger agents, photocatalytic degradation processes mainly depended on the specific pollutant type, while irradiation sources barely defined the photocatalytic mechanism. On the other hand, changes in irradiation intensity significantly influenced the photolysis process, while photocatalysis was slightly affected, indicating that irradiation spectra are more relevant than intensity.
| S-EPMC9696933 | biostudies-literature
Project description:In this study, the photocatalytic activity of nanomaterials Ag/AgX (X = Cl, Br, I) is reported. Highly efficient silver halide (Ag/AgX where X = Cl, Br, I) photocatalysts were synthesized through a hydrothermal method. The samples were characterized using a range of techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) to check their structural, morphology, textural and optical properties. In addition, the photocatalytic activity of photocatalysts was evaluated through the degradation of 2,4-dichlorophenol (2,4-DCP) under UV and visible light irradiation. XRD analysis confirmed the presence of a single-phase structure (pure phase) in the synthesized photocatalysts. SEM micrographs showed agglomeration with a non-uniform distribution of particles, which is a characteristic of surfactant-free precipitation reactions in aqueous media. The Ag/AgBr photocatalyst exhibited the best degradation efficiency, resulting in 83.37% and 89.39% photodegradation after 5 h of UV and visible light irradiation, respectively. The effect of catalyst loading, initial solution pH, and 2,4-DCP concentration was investigated for the best-performing Ag/AgBr photocatalyst. The degradation kinetics were best described by the pseudo-first-order Langmuir-Hinshelwood model. The photocatalytic capacity of Ag/AgBr decreased by 50% after five reuse cycles. SEM images revealed heightened levels of photodegradation on the catalyst surface. The study proved the feasibility of using simple synthesis methods to produce visible light active photocatalysts capable of degrading refractory phenolic pollutants in aqueous systems.
| S-EPMC10869396 | biostudies-literature
Project description:Titanium dioxide nanoparticles were synthesized by laser pyrolysis, their surface and electronic properties were modified by gold and/or nitrogen. These materials were characterized by different techniques like X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance (EPR). Time resolved conductivity (TRMC) was used to study the charge separation of electron/hole pairs. Altogether (XPS, EPR, TRMC), the physicochemical characterizations are well correlated with chemical photoactivity of the different samples. Their photocatalytic activity was evaluated for the degradation of linear carboxylic acids (C2-C3) under UV and visible illumination. The decomposition rate of acids was measured, it shows that the modification with gold increases the photoactivity while the presence of nitrogen slows down the process. Such observations are in good agreement with evolution of TRMC signals. A degradation pathway has been determined by identification of intermediate products by chromatography and EPR, results show different intermediate species. In particular EPR confirms the presence of NO2- paramagnetic centers and shows two novel N centered paramagnetic centers. A decrease of the degradation rate is observed with increase of carboxylic acid chain length.
| S-EPMC5678285 | biostudies-literature
Project description:Iron (III) oxide (Fe3O4) and sodium dodecyl sulfate (SDS) coated iron (III) oxide (SDS@Fe3O4) nanoparticles (NPs) were synthesized by the co-precipitation method for application in the catalytic degradation of Rhodamine B (RB) dye. The synthesized NPs were characterized using X-ray diffractometer (XRD), vibrating sample magnetometer (VSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infra-red (FT-IR) spectroscopy techniques and tested in the removal of RB. A kinetic study on RB degradation by hydrogen peroxide (H2O2) was carried out and the influence of Fe3O4 and SDS@Fe3O4 magnetic NPs on the degradation rate was assessed. The activity of magnetic NPs, viz. Fe3O4 and SDS@Fe3O4, in the degradation of RB was spectrophotometrically studied and found effective in the removal of RB dye from water. The rate of RB degradation was found linearly dependent upon H2O2 concentration and within 5.0 × 10-2 to 4.0 × 10-1 M H2O2, the observed pseudo-first-order kinetic rates (kobs, s-1) for the degradation of RB (10 mg L-1) at pH 3 and temperature 25 ± 2 °C were between 0.4 and 1.7 × 104 s-1, while in presence of 0.1% w/v Fe3O4 or SDS@Fe3O4 NPs, kobs were between 1.3 and 2.8 × 104 s-1 and between 2.6 and 4.8 × 104 s-1, respectively. Furthermore, in presence of Fe3O4 or SDS@Fe3O4, kobs increased with NPs dosage and showed a peaked pH behavior with a maximum at pH 3. The magnitude of thermodynamic parameters Ea and ΔH for RB degradation in presence of SDS@Fe3O4 were 15.63 kJ mol-1 and 13.01 kJ mol-1, respectively, lowest among the used catalysts, confirming its effectiveness during degradation. Furthermore, SDS in the presence of Fe3O4 NPs and H2O2 remarkably enhanced the rate of RB degradation.
| S-EPMC7650585 | biostudies-literature
Project description:Hierarchical mesoporous TiO2 was synthesized via a solvothermal technique. The sonochemical method was adopted to decorate plasmonic nanoparticles (NPs) (Ag, Au) on the pores of mesoporous TiO2. The crystallinity, structure, and morphology were determined to understand the physicochemical nature of the nanocomposites. The catalytic efficiency of the plasmonic nanocatalysts was tested for the azo dyes (congo red, methyl orange, acid orange 10, and remazol red) under solar and visible light irradiations. The generation of hydroxyl radicals was also studied using terephthalic acid as a probe molecule. An attempt was made to understand the influence of size, work function and Fermi level of the metal NPs toward the efficiency of the photocatalyst. The efficiency of the nanocomposites was found to be in the order of P25 < mesoporous TiO2 < mesoporous Ag-TiO2 < mesoporous Au-TiO2 nanospheres under both direct solar light and visible light irradiation. The results indicated that the adsorption of dye, anatase phase, and surface plasmon resonance of NPs favored the effective degradation of dyes in aqueous solution. Further, the efficiency of the catalyst was also tested for xanthene (rose bengal), rhodamine (rhodamine B, rhodamine 6G), and thiazine (methylene blue) dyes. Both TiO2 and NPs (Ag & Au) possess a huge potential as an eco-friendly photocatalyst for wastewater treatment.
| S-EPMC6644734 | biostudies-literature