Photovoltaic and Impedance Spectroscopy Study of Screen-Printed TiO₂ Based CdS Quantum Dot Sensitized Solar Cells.
Ontology highlight
ABSTRACT:
SUBMITTER: Atif M
PROVIDER: S-EPMC5455228 | biostudies-other | 2015 Jan
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Quantum dot (QD)-sensitized solar cells (QDSSCs) are expected to achieve higher energy conversion efficiency than traditional single-junction silicon solar cells due to the unique properties of QDs. An inverse opal (IO)-TiO₂ (IO-TiO₂) electrode is useful for QDSSCs because of its three-dimensional (3D) periodic nanostructures and better electrolyte penetration compared to the normal nanoparticles (NPs)-TiO₂ (NPs-TiO₂) electrode. We find that the open-circuit voltages Voc of the QDSSCs with IO-TiO₂ electrodes are higher than those of QDSSCs with NPs-TiO₂ electrodes. One important strategy for enhancing photovoltaic conversion efficiency of QDSSCs with IO-TiO₂ electrodes is surface passivation of photoanodes using wide-bandgap semiconducting materials. In this study, we have proposed surface passivation on IO-TiO₂ with ZnS coating before QD deposition. The efficiency of QDSSCs with IO-TiO₂ electrodes is largely improved (from 0.74% to 1.33%) because of the enhancements of Voc (from 0.65 V to 0.74 V) and fill factor (FF) (from 0.37 to 0.63). This result indicates that ZnS passivation can reduce the interfacial recombination at the IO-TiO₂/QDs and IO-TiO₂/electrolyte interfaces, for which two possible explanations can be considered. One is the decrease of recombination at IO-TiO₂/electrolyte interfaces, and the other one is the reduction of the back-electron injection from the TiO₂ electrode to QDs. All of the above results are effective for improving the photovoltaic properties of QDSSCs.
| S-EPMC6071099 | biostudies-literature
Project description:A hierarchical array of ZnO nanocones covered with ZnO nanospikes was hydrothermally fabricated and employed as the photoanode in a CdS quantum dot-sensitized solar cell (QDSSC). This QDSSC outperformed the QDSSC based on a simple ZnO nanocone photoanode in all the four principal photovoltaic parameters. Using the hierarchical photoanode dramatically increased the short circuit current density and also slightly raised the open circuit voltage and the fill factor. As a result, the conversion efficiency of the QDSSC based on the hierarchical photoanode was more than twice that of the QDSSC based on the simple ZnO nanocone photoanode. This improvement is attributable to both the enlarged specific area of the photoanode and the reduction in the recombination of the photoexcited electrons.
| S-EPMC4574909 | biostudies-literature
Project description:Various cell crack modes (with or without electrically inactive cell areas) can be induced in crystalline silicon photovoltaic (PV) cells within a PV module through natural thermomechanical stressors such as strong winds, heavy snow, and large hailstones. Although degradation in the performance of PV modules by cell cracks has been reported occasionally, the mode-dependent evolutions in the electrical signatures of cracks have not yet been elucidated. In this study, we propose that the reduction of the time constant in the AC impedance spectra, which is caused by the elevation of minority-carrier recombination in the p-n junction of a PV cell, is a ubiquitous signature of cracked PV cells encapsulated in a commercially available PV module. Several other characteristics derived from the illuminated current-voltage (I-V) and dark I-V data significantly evolved only in PV cells with inactive cell areas. We also propose that the evaluation by carrier recombination is a crucial diagnostic technique for detecting all crack modes, including microcracks, in wafer-based PV modules.
| S-EPMC9671427 | biostudies-literature
Project description:Here we present the photoelectrocatalytic hydrogen generation properties of CdS passivated ZnCuInSe (ZCISe) quantum dots (QDs) supported by TiO₂ nanowires decorated with Ag nanoparticles. In this configuration, Ag nanoparticles were sandwiched between the photo-electrons collector (TiO₂) and photo-sensitizers (ZCISe), and acted as an electron relay speeding up the charge carrier transport. ZCISe and CdS enabled the optical absorption of the photoelectrode ranging from ultraviolet to near infrared region, which significantly enhanced the solar-to-chemical energy conversion efficiency. A photocurrent of 10.5 mA/cm² and a hydrogen production rate of about 52.9 μmol/h were achieved under simulated sunlight (1.5 AG).
| S-EPMC6474140 | biostudies-literature
Project description:In the present work, we report the use of bacterial cells for the production of CdS/CdSe Core/Shell quantum dots (QDs), a complex nanostructure specially designed to improve their performance as photosensitizer in photovoltaic devices. The method requires the incorporation of L-cysteine, CdCl2 and Na2SeO3 to Escherichia coli cultures and allows a tight control of QDs properties. The obtained CdS/CdSe QDs were photophysically and structurally characterized. When compared to CdS QDs, the classical shift in the UV-visible spectra of Core/Shell nanostructures was observed in CdS/CdSe QDs. The nanosize, structure, and composition of Core/Shell QDs were confirmed by TEM and EDS analysis. QDs presented a size of approximately 12 nm (CdS) and 17 nm (CdS/CdSe) as determined by dynamic light scattering (DLS), whereas the fourier transform infrared (FTIR) spectra allowed to distinguish the presence of different biomolecules bound to both types of nanoparticles. An increased photostability was observed in CdS/CdSe nanoparticles when compared to CdS QDs. Finally, biosynthesized CdS/CdSe Core/Shell QDs were used as photosensitizers for quantum dots sensitized solar cells (QDSSCs) and their photovoltaic parameters determined. As expected, the efficiency of solar cells sensitized with biological CdS/CdSe QDs increased almost 2.5 times when compared to cells sensitized with CdS QDs. This work is the first report of biological synthesis of CdS/CdSe Core/Shell QDs using bacterial cells and represents a significant contribution to the development of green and low-cost photovoltaic technologies.
| S-EPMC6637821 | biostudies-literature
Project description:Size controllable TiO2 hollow microspheres (HMS) were synthesized by a carbonaceous spheres (CS) template method. Based on TiO2 HMS, the ZnS/CdS quantum dots (QDs) were loaded to form a ZnS/CdS@TiO2 HMS photoanode for quantum dots sensitized solar cell (QDSSC). The size effects of TiO2 HMS on photovoltaic performance were investigated, and showed that TiO2 HMS with sizes ~560 nm produced the best short-circuit current density (Jsc) of 8.02 mA cm-2 and highest power conversion efficiency (PCE) of 1.83%, showing a better photovoltaic performance than any other QDSSCs based on TiO2 HMS with size ~330 nm, ~400 nm, and ~700 nm. The improvement of photovoltaic performance based on ~560 nm TiO2 HMS which can be ascribed to the enhanced light harvesting efficiency caused by multiple light reflection and strong light scattering of TiO2 HMS. The ultraviolet-visible (UV-vis) spectra and incident photo to the current conversion efficiency (IPCE) test results confirmed that the size of TiO2 HMS has an obvious effect on light harvesting efficiency. A further application of ~560 nm TiO2 HMS in ZnS/PbS/CdS QDSSC can improve the PCE to 2.73%, showing that TiO2 HMS has wide applicability in the design of QDSSCs.
| S-EPMC6566662 | biostudies-literature
Project description:The preparation of quantum dot (QD)-sensitized photoanodes, especially the deposition of QDs on TiO2 matrix, is usually a time-extensive and performance-determinant step in the construction of QD-sensitized solar cells (QDSCs). Herein, a transformative approach for immobilizing QD on the TiO2 matrix was developed by simply mixing the as-prepared oil-soluble QDs with TiO2 P25 particles suspension for a period as short as half a minute. The solar paint was prepared by adding the TiO2/QD composite in a binder solution under ultrasonication. The QD-sensitized photoanodes were then obtained by simply brushing the solar paint on a fluorine-doped tin oxide substrate followed by a low-temperature annealing at ambient atmosphere. Sandwich-structured complete QDSCs were assembled with the use of Cu2S/brass as counter electrode and polysulfide redox couple as an electrolyte. The photovoltaic performance of the resulting Zn-Cu-In-Se (ZCISe) QDSCs was evaluated after primary optimization of the QD/TiO2 ratio as well as the thicknesses of photoanode films. In this proof of concept with a simple solar paint approach for photoanode films, an average power conversion efficiency of 4.13% (J sc = 11.11 mA/cm2, V oc = 0.590 V, fill factor = 0.631) was obtained under standard irradiation condition. This facile solar paint approach offers a simple and convenient approach for QD-sensitized photoanodes in the construction of QDSCs.
| S-EPMC6641499 | biostudies-literature
Project description:Despite great efforts dedicated to enhance power conversion efficiency (PCE) of quantum dot-sensitized solar cells (QDSSCs) in the past two decades, the efficiency of QDSSCs is still far behind its theoretical value. The present approaches for improving PCE are mainly focused on tailoring the bandgap of QDs to broadening light-harvesting and optimizing interfaces of component parts. Herein, a new solar cell architecture is proposed by integrating concentrating solar cell (CPV) concept into QDSSCs with double photoanode design. The Cu2S mesh is used as a counter electrode and sandwiched between two photoanodes. This designed battery structure can increase the PCE by 260% compared with a single photoanode. With the most extensively used CdS/CdSe QD sensitizers, a champion PCE of 8.28% (Voc = 0.629 V, Jsc = 32.247 mA cm-2) was achieved. This is mainly due to the increase in Jsc due to the double photoanode design and adoption of the CPV concept. In addition, another reason is that concentrated sunshine illumination induced a photothermal effect, accelerating the preceding chemical reactions associated with the conversion of polysulfide species. The cell fabrication and design reported here provides a new insight for further development of QDSSCs.
| S-EPMC7524932 | biostudies-literature
Project description:CdS/CdSe quantum dot-sensitized solar cells (QDSSCs) were fabricated on two types of TiO2 photoanodes, namely nanosheets (NSs) and nanoparticles. The TiO2 NSs with high (001)-exposed facets were prepared via a hydrothermal method, while the TiO2 nanoparticles used the commercial Degussa P-25. It was found that the pore size, specific surface area, porosity, and electron transport properties of TiO2 NSs were generally superior to those of P-25. As a result, the TiO2 NS-based CdS/CdSe QDSSC has exhibited a power conversion efficiency of 4.42%, which corresponds to a 54% improvement in comparison with the P-25-based reference cell. This study provides an effective photoanode design using nanostructure approach to improve the performance of TiO2-based QDSSCs.
| S-EPMC6329687 | biostudies-other
Project description:In this study, to obtain high performances of the dye-sensitized solar cells using the optimal TiO2 photoelectrode for the synthesized pyrazine-based organic photosensitizers, three types of TiO2 photoelectrodes were fabricated and evaluated for comparison. The double-layered nanoporous TiO2 photoelectrode (SPD type) consisted of a dispersed TiO2 layer and a transparent TiO2 layer. The single-layered nanoporous TiO2 photoelectrodes (D type and SP type) consisted of a dispersed TiO2 layer and a transparent TiO2 layer, respectively. The surface area, pore volume, and crystalline structures of the three types of TiO2 photoelectrodes were analyzed by Brunauer-Emmett-Teller method, field-emission scanning electron microscopy, and X-ray diffractometry to confirm their crystallinity and surface morphology. The structures of the three types of TiO2 photoelectrode-adsorbed organic sensitizers were investigated using X-ray photoelectron spectroscopy. The photovoltaic performances of DSSC devices using three organic photosensitizers adsorbed onto the three types of TiO2 photoelectrodes were investigated under a light intensity of 100 mW/cm2 at AM 1.5. The DSSC device using double-layered SPD type TiO2 photoelectrodes displayed 1.31∼2.64% efficiency, compared to single-layered SP type TiO2 photoelectrodes (1.31∼2.50%) and D type TiO2 photoelectrodes (0.90∼1.54%), using organic photosensitizers. The DSSC device using the SPD type TiO2 photoelectrode and trifluoromethylbenzopyrazine (TPPF) as a photosensitizer showed the highest performances: J sc of 5.69 mA/cm2, V oc of 0.69 V, FF of 0.67, and efficiency of 2.64%. The relationship between photovoltaic effects and interfacial resistance characteristics of DSSCs using the three organic photosensitizers adsorbed onto the three types of TiO2 photoelectrodes could be interpreted from interfacial resistances according to frequency through impedance analysis.
| S-EPMC10134224 | biostudies-literature