Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Evaluation and Description of Friction between an Electro-Deposited Coating and a Ceramic Ball under Fretting Condition.

ABSTRACT: This article describes fretting behavior of zirconia and silicon nitride balls on an electro-deposited coating. Fretting tests are performed using a ball-on-flat configuration. The evolution of the kinetic friction coefficient is determined, along with slip ratio. Experimental results show that the steady-state friction coefficient between ceramic balls (Si₃N₄ and ZrO₂) and an electro-deposited coating is about 0.06, lower than the value between AISI 52100 ball and the coating. After a steady-state sliding, the transition of the friction coefficient is varied with a ball. The friction coefficient for ZrO₂ balls became a critical value after higher fretting cycles than those for Si₃N₄ and AISI 52100 balls. In addition, it is identified that two parameters can describe the transition of the friction coefficient. Finally, the evolution of the friction coefficient is expressed as an exponential or a power-law form.

SUBMITTER: Kim K

PROVIDER: S-EPMC5455471 | biostudies-other | 2015 Jul

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

The Contact Ageing Effect on Fretting Damage of an Electro-Deposited Coating against an AISI52100 Steel Ball.

Project description:This article investigates the effect of contact ageing on fretting damage of an epoxy-based cathodic electro-deposited coating for use on automotive seat slide tracks (made of cold-rolled high strength steel). Static normal load was induced at the contact between the coating and an AISI52100 ball for a certain duration. It was identified that plastically deformed contact area increased logarithmically as a function of time when the contact was under static normal load. Fretting tests after various durations of static contact were conducted using a ball-on-flat plate apparatus. All fretting tests were halted when the friction coefficient reached a critical value of 0.5, indicating complete coating failure. The total number of fretting cycles to the critical friction coefficient was found to vary with the duration of static contact before fretting. It was identified that the number of cycles to the critical friction coefficient decreased with the increased duration of static contact. Meanwhile, the friction coefficient at steady-state sliding was not greatly affected by the duration of static contact before fretting. Finally, the relation between coating thickness after indentation creep and the number of cycles to the critical friction coefficient was found to be linear. Obtained results show that the duration of static contact before fretting has an influence on the fretting lifetime of an electro-deposited coating.

| S-EPMC5457045 | biostudies-other

Reciprocal Sliding Friction Model for an Electro-Deposited Coating and Its Parameter Estimation Using Markov Chain Monte Carlo Method.

Project description:This paper describes a sliding friction model for an electro-deposited coating. Reciprocating sliding tests using ball-on-flat plate test apparatus are performed to determine an evolution of the kinetic friction coefficient. The evolution of the friction coefficient is classified into the initial running-in period, steady-state sliding, and transition to higher friction. The friction coefficient during the initial running-in period and steady-state sliding is expressed as a simple linear function. The friction coefficient in the transition to higher friction is described with a mathematical model derived from Kachanov-type damage law. The model parameters are then estimated using the Markov Chain Monte Carlo (MCMC) approach. It is identified that estimated friction coefficients obtained by MCMC approach are in good agreement with measured ones.

| S-EPMC5502884 | biostudies-other

Diamond-like carbon coating under oleic acid lubrication: Evidence for graphene oxide formation in superlow friction.

Project description:The achievement of the superlubricity regime, with a friction coefficient below 0.01, is the Holy Grail of many tribological applications, with the potential to have a remarkable impact on economic and environmental issues. Based on a combined high-resolution photoemission and soft X-ray absorption study, we report that superlubricity can be realized for engineering applications in bearing steel coated with ultra-smooth tetrahedral amorphous carbon (ta-C) under oleic acid lubrication. The results show that tribochemical reactions promoted by the oil lubrication generate strong structural changes in the carbon hybridization of the ta-C hydrogen-free carbon, with initially high sp3 content. Interestingly, the macroscopic superlow friction regime of moving mechanical assemblies coated with ta-C can be attributed to a few partially oxidized graphene-like sheets, with a thickness of not more than 1 nm, formed at the surface inside the wear scar. The sp2 planar carbon and oxygen-derived species are the hallmark of these mesoscopic surface structures created on top of colliding asperities as a result of the tribochemical reactions induced by the oleic acid lubrication. Atomistic simulations elucidate the tribo-formation of such graphene-like structures, providing the link between the overall atomistic mechanism and the macroscopic experimental observations of green superlubricity in the investigated ta-C/oleic acid tribological systems.

| S-EPMC5388889 | biostudies-literature

Collision-enhanced friction of a bouncing ball on a rough vibrating surface.

Project description:We describe experiments and simulations to investigate the dynamics of a ball bouncing on a rough vibrating surface. Directly measuring the impulse due to each bounce we find that the frictional interaction with the surface is strongly enhanced near to the side wall. The enhanced dissipation arises as a consequence of the coupling between the collision, rotation and surface friction. This dissipation, which for our experimental conditions was estimated to be up to three times larger than the more obvious inelastic collision, can result in an enhanced probability density near boundaries and particle-particle spatial correlations. Our findings imply that the effective particle collision properties cannot be considered independently of the surface's frictional properties.

| S-EPMC7801373 | biostudies-literature

Chemical-Vapor-Deposited Graphene as a Thermally Conducting Coating.

Project description:We performed scanning thermal microscopy measurements on single layers of chemical-vapor-deposited (CVD) graphene supported by different substrates, namely, SiO2, Al2O3, and PET using a double-scan technique to remove the contribution to the heat flux through the air and the cantilever. Then, by adopting a simple lumped-elements model, we developed a new method that allows determining, through a multistep numerical analysis, the equivalent thermal properties of thermally conductive coatings of nanometric thickness. In this specific case we found that our CVD graphene is "thermally equivalent", for heat injection perpendicular to the graphene planes, to a coating material of conductivity k eff = 2.5 ± 0.3 W/m K and thickness t eff = 3.5 ± 0.3 nm in perfect contact with the substrate. For the SiO2 substrate, we also measured stacks made of 2- and 4-CVD monolayers, and we found that the effective thermal conductivity increases with increasing number of layers and, with a technologically achievable number of layers, is expected to be comparable to that of 1 order of magnitude-thicker metallic thin films. This study provides a powerful method for characterizing the thermal properties of graphene in view of several thermal management applications.

| S-EPMC6541428 | biostudies-literature

Vapor-Deposited Reactive Coating with Chemically and Topographically Erasable Properties.

Project description:An erasable coating was prepared to modify material surfaces with accessibilities, including specific conjugation, elimination of the conjugated chemistry/function, and the reactivation of a second new chemistry/function. The coating was realized based on a vapor-deposited functional poly-p-xylylene coating composed of an integrated 3-((3-methylamido)-disulfanyl)propanoic acid functional group, resulting in not only chemical reactivity, but also a disulfide interchange mechanism. Mechanically, the coating was robust in terms of the thermal stability and adhesive property on a variety of substrate materials. Chemically, the anchoring site of carboxylic acid was accessible for specific conjugation, and a disulfide bridge moiety was used to disengage already installed functions/properties. In addition, the homogeneous nature of the vapor-phased coating technique is known for its morphology/thickness and distribution of the functional moiety, which allowed precision to address the installation or erasure of functions and properties. Characterization of the precisely confined hydrophilic/hydrophobic wetting property and the alternating reversibility of this wetting property on the same surface was achieved.

| S-EPMC6835693 | biostudies-literature

Utility of lens coating with liquid ceramic for gastrointestinal endoscopic submucosal dissection

Project description:Interventions: ESD using endoscope coated with liquid ceramic ESD using conventional endoscope Primary outcome(s): visibility(every 15 minutes and the end of procedure) Study Design: Parallel Randomized

| 2644968 | ecrin-mdr-crc

Homogeneity of ball milled ceramic powders: Effect of jar shape and milling conditions.

Project description:This paper contains data and supporting information of and complementary to the research article entitled "Effect of jar shape on high-energy planetary ball milling efficiency: simulations and experiments" (Broseghini et al.,) [1]. Calcium fluoride (CaF2) was ground using two jars of different shape (cylindrical and half-moon) installed on a planetary ball-mill, exploring different operating conditions (jar-to-plate angular velocity ratio and milling time). Scanning Electron Microscopy (SEM) images and X-Ray Powder Diffraction data (XRPD) were collected to assess the effect of milling conditions on the end-product crystallite size. Due to the inhomogeneity of the end product, the Whole Powder Pattern Model (WPPM, (Scardi, 2008) [2]) analysis of XRPD data required the hypothesis of a bimodal distribution of sizes - respectively ground (fine fraction) and less-to-not ground (coarse fraction) - confirmed by SEM images and suggested by the previous literature (Abdellatief et al., 2013) [3,4]. Predominance of fine fraction clearly indicates optimal milling conditions.

| S-EPMC5149052 | biostudies-literature

Ceramic

Project description:Post-Infective Bowel Dysfunction following Campylobacter enteritis is characterised by reduced microbiota diversity and impaired microbiota recovery

| PRJEB52306 | ENA

Friction Dynamics of Foams under Nonlinear Motion.

Project description:Foams are viscoelastic soft materials with complex mechanical properties. Here, we evaluated the friction dynamics of foams between acrylic plates using a sinusoidal motion friction evaluation system and we found some interesting characteristics under accelerated conditions. On a typical solid surface, a symmetrical friction profile, in which static and kinetic frictions are observed, is obtained under reciprocating nonlinear motion. Meanwhile, significant lubricant effects and velocity-dependent friction profiles without static friction were observed in foams. The friction force in foams increased in proportion to the power of velocity, with a power index of <1. These characteristic and dynamic phenomena in foams were observed in this study. They had been caused by the formation of a thick lubricant film and various dissipative modes including surfactant diffusion, viscous dissipation, and wall slip of bubbles. Moreover, the addition of a thickener increased the friction force and the delay time of friction response and improved the foam durability against normal force and shear. These findings are useful for understanding dynamic phenomena in soft materials.

| S-EPMC9118422 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data