Experimental Studies on the Flammability and Fire Hazards of Photovoltaic Modules.
Ontology highlight
ABSTRACT:
SUBMITTER: Yang HY
PROVIDER: S-EPMC5455650 | biostudies-other | 2015 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description:This work investigated experimentally and theoretically the fire hazards of thermal-insulation materials used in diesel locomotives under different radiation heat fluxes. Based on the experimental results, the critical heat flux for ignition was determined to be 6.15 kW/m² and 16.39 kW/m² for pure polyurethane and aluminum-polyurethane respectively. A theoretical model was established for both to predict the fire behaviors under different circumstances. The fire behavior of the materials was evaluated based on the flashover and the total heat release rate (HRR). The fire hazards levels were classified based on different experimental results. It was found that the fire resistance performance of aluminum-polyurethane is much better than that of pure-polyurethane under various external heat fluxes. The concentration of toxic pyrolysis volatiles generated from aluminum-polyurethane materials is much higher than that of pure polyurethane materials, especially when the heat flux is below 50 kW/m². The hazard index HI during peak width time was proposed based on the comprehensive impact of time and concentrations. The predicted HI in this model coincides with the existed N-gas and FED models which are generally used to evaluate the fire gas hazard in previous researches. The integrated model named HNF was proposed as well to estimate the fire hazards of materials by interpolation and weighted average calculation.
| S-EPMC5456725 | biostudies-other
Project description:Indoor photovoltaic (IPV) with power output over 100 μW is promising to power the numerous sensor nodes in the Internet of Things (IoT) ecosystem. All polymer photovoltaic has the advantages of excellent thermal stability and superior mechanical properties. In this work, we fabricate the first all-polymer indoor photovoltaic module with the active area of 10 cm2. The module uses polymer donor CD1 and new polymer acceptor PBN-21 with medium optical band gap of 1.9 eV as the active layer. It is processed with eco-friendly solvent tetrahydrofuran and the morphology can be improved by blade coating at 55°C. Under light emitting diode illumination at 1000 lux, the module exhibits a power conversion efficiency of 12.04% and a power output of 367.2 μW. The sufficient power output, high efficiency, excellent stability, and eco-friendly processing indicate that all-polymer indoor photovoltaic is a promising approach to achieve the self-powered of sensor nodes in the IoT ecosystem.
| S-EPMC8476653 | biostudies-literature
Project description:In the twenty-first century, energy sustainability and reliability are one of the major challenges in the world and prime factors of the national development plan. Recently, Solar PV is gaining popularity and making a significant effect as an alternative to fossil fuels due to reduction of cost and enhanced efficiency. However, the production performance of Solar PV over the period gets significantly impacted owing to a variety of problems such as dust, aging due to shading and soiling over the cell, hot spot, discoloration and corrosion for excessive atmospheric temperature, inadequate solar light, cell damage, and so on. In this research, a low-cost halogen-based artificial sun simulator is developed and deployed to examine the electrical properties of Solar PV in indoor conditions. Two monocrystalline and three polycrystalline PV panels under Standard Test Conditions, as well as a prototype 5 × 8 PV array, using this artificial light source, were evaluated rigorously for experimental purposes. With the help of a microcontroller-based I-V tracer and an actual data storage system, Open Circuit Voltage (Voc), Short Circuit Current (Isc), Maximum Power Voltage (Vmp), Maximum Power Current (Imp), and Maximum Power (Pmax) at three irradiance levels were measured and recorded. Utilizing Microsoft Excel software, the data logger's recorded data were analyzed and I-V and P-V curves were plotted. These data are extremely valuable for obtaining a good understanding of the validity of the Sun Simulator and the rate of deterioration of solar PV performance depending on irradiance. These data will aid the research community in future research regarding PV array performance monitoring, corresponding solution modeling, and developing cost-effective installation of large-scale PV arrays.
| S-EPMC9249606 | biostudies-literature
Project description:The use of solar photovoltaic systems (PVs) is increasing as a clean and affordable source of electric energy. The Pv cell is the main component of the PV system. To improve the performance, control, and evaluation of the PV system, it is necessary to provide accurate design and to define the intrinsic parameters of the solar cells. There are many methods for optimizing the parameters of the solar cells. The first class of methods is called the analytical methods that provide the model parameters using datasheet information or I-V curve data. The second class of methods is the optimization-based methods that define the problem as an optimization problem. The optimization problem objective is to minimize the error metrics and it is solved using metaheuristic optimization algorithms. The third class of methods is composed of a hybrid of both the analytical and the metaheuristic approaches, some parameters are computed by the analytical approach and the rest are found using metaheuristic optimization algorithms. Research in this area faces two challenges; (1) finding an optimal model for the parameters of the solar cells and (2) the lack of data about the photovoltaic cells. This paper proposes an optimization-based algorithm for accurately estimating the parameters of solar cells. It is using the Improved Equilibrium Optimizer algorithm (IEO). This algorithm is improved using the Opposition Based Learning (OBL) at the initialization phase of EO to improve its population diversity in the search space. Opposition-based Learning (OBL) is a new concept in machine learning inspired by the opposite relationship among entities. There are two common models for solar cells; the single diode model (SDM) and double diode model (DDM) have been used to demonstrate the capabilities of IEO in estimating the parameters of solar cells. The proposed methodology can find accurate solutions while reducing the computational cost. Compared to other existing techniques, the proposed algorithm yields less mean absolute error. The results were compared with seven optimization algorithms using data of different solar cells and PV panels. The experimental results revealed that IEO is superior to the most competitive algorithms in terms of the accuracy of the final solutions.
| S-EPMC8444076 | biostudies-literature
Project description:Soiling by dry deposition affects the power output of photovoltaic (PV) modules, especially under dry and arid conditions that favor natural atmospheric aerosols (wind-blown dust). In this paper, we report on measurements of the soiling effect on the energy yield of grid-connected crystalline silicon PV modules deployed in five cities across a north-south transect of approximately 1300?km in the Atacama Desert ranging from latitude 18°S to latitude 30°S. Energy losses were assessed by comparing side-by-side outputs of four co-planar PV modules. Two of the PV modules of the array were kept clean as a control, while we allowed the other two to naturally accumulate soiling for 12 months (from January 2017 to January 2018). We found that the combination of high deposition rates and infrequent rainfalls led to annual energy losses that peaked at 39% in the northern coastal part of the desert. In contrast, annual energy losses of 3% or less were measured at relatively high-altitude sites and also at locations in the southern part of the desert. For comparison, soiling-induced annual energy losses of about 7% were measured in Santiago, Chile (33°S), a major city with higher rainfall frequency but where urban pollution plays a significant role.
| S-EPMC6141476 | biostudies-literature
Project description:Photovoltaic devices based on perovskite materials have a great potential to become an exceptional source of energy while preserving the environment. However, to enter the global market, they require further development to achieve the necessary performance requirements. The environmental performance of a pre-industrial process of production of a large-area carbon stack perovskite module is analyzed in this work through life cycle assessment (LCA). From the pre-industrial process an ideal process is simulated to establish a benchmark for pre-industrial and laboratory-scale processes. Perovskite is shown to be the most harmful layer of the carbon stack module because of the energy consumed in the preparation and annealing of the precursor solution, and not because of its Pb content. This work stresses the necessity of decreasing energy consumption during module preparation as the most effective way to reduce environmental impacts of perovskite solar cells.
| S-EPMC6286418 | biostudies-literature
Project description:Global exponential increase in levels of Photovoltaic (PV) module waste is an increasing concern. The purpose of this study is to investigate if there is energy value in the polymers contained within first-generation crystalline silicon (c-Si) PV modules to help contribute positively to recycling rates and the circular economy. One such thermochemical conversion method that appeals to this application is pyrolysis. As c-Si PV modules are made up of glass, metal, semiconductor and polymer layers; pyrolysis has potential not to promote chemical oxidation of any of these layers to help aid delamination and subsequently, recovery. Herein, we analysed both used polymers taken from a deconstructed used PV module and virgin-grade polymers prior to manufacture to determine if any properties or thermal behaviours had changed. The calorific values of the used and virgin-grade Ethylene vinyl acetate (EVA) encapsulant were found to be high, unchanged and comparable to that of biodiesel at 39.51 and 39.87 MJ.Kg-1, respectively. This result signifies that there is energy value within used modules. As such, this study has assessed the pyrolysis behaviour of PV cells and has indicated the energy recovery potential within the used polymers found in c-Si PV modules.
| S-EPMC6437152 | biostudies-literature
Project description:Energy recovery from renewable sources is a very attractive, and sometimes, challenging issue. To recover solar energy, the production of photovoltaic (PV) modules becomes a prosperous industrial certainty. An important material in PV modules production and correct functioning is the encapsulant material and it must have a good performance and durability. In this work, accurate characterizations of performance and durability, in terms of photo- and thermo-oxidation resistance, of encapsulants based on PolyEthylene Vinyl Acetate (EVA) and PolyOlefin Elastomer (POE), containing appropriate additives, before (pre-) and after (post-) lamination process have been carried out. To simulate industrial lamination processing conditions, both EVApre-lam and POEpre-lam sheets have been subjected to prolonged thermal treatment upon high pressure. To carry out an accurate characterization, differential scanning calorimetry, rheological and mechanical analysis, FTIR and UV-visible spectroscopy analyses have been performed on pre- and post-laminated EVA and POE. The durability, in terms of photo- and thermo-oxidation resistance, of pre-laminated and post-laminated EVA and POE sheets has been evaluated upon UVB exposure and prolonged thermal treatment, and the progress of degradation has been monitored by spectroscopy analysis. All obtained results agree that the lamination process has a beneficial effect on 3D-structuration of both EVA and POE sheets, and after lamination, the POE shows enhanced rigidity and appropriate ductility. Finally, although both EVA and POE can be considered good candidates as encapsulants for bifacial PV modules, it seems that the POE sheets show a better resistance to oxidation than the EVA sheets.
| S-EPMC8914825 | biostudies-literature
Project description:Sun light as a renewable energy resource is getting popular day by day. Power production from a solar power plant is extensively dependent on the weather condition, daylight duration, available sunlight, air quality etc. Thus installation of large scale solar power plant requires long term feasibility study, previous five years weather data, lifetime of the solar panel, projected maintenance requirement and man power. In this survey we have visited several sites of roof top solar power plants in the Dhaka city which are aged at least five years. Firstly, we have conducted visual study of the solar panels on the roof top for visible degradation due to environment and ageing. Then we have measured Current-Voltage characteristics under sun light using portable PV-200 Seaward I-V Tracer. The Current-Voltage data were analyzed using 'Seaward Solar Chart' data analysis tool. The tool was used to plot Current-Voltage and Power-Voltage curves. From the data we have estimated the Standard Test Condition (STC) power, Fill Factor (F.F) and Efficiency of selected photovoltaic modules. To get a clear view over the experience of installed rooftop solar photovoltaic modules in Dhaka city, the data will be useful. The data will help us to project the challenges and provide a guide line to maintain an economically viable solar photovoltaic installation.
| S-EPMC7267713 | biostudies-literature
Project description:We report for the first time a successful fabrication and operation of an InAs/GaAs quantum dot based intermediate band solar cell concentrator photovoltaic (QD-IBSC-CPV) module to the IEC62108 standard with recorded power conversion efficiency of 15.3%. Combining the measured experimental results at Underwriters Laboratory (UL®) licensed testing laboratory with theoretical simulations, we confirmed that the operational characteristics of the QD-IBSC-CPV module are a consequence of the carrier dynamics via the intermediate-band at room temperature.
| S-EPMC3999453 | biostudies-literature