Microwave Irradiation Effect on the Dispersion and Thermal Stability of RGO Nanosheets within a Polystyrene Matrix.
Ontology highlight
ABSTRACT:
SUBMITTER: Alsharaeh EH
PROVIDER: S-EPMC5455820 | biostudies-other | 2014 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description:This work compares the preparation of nanocomposites of polystyrene (PS), poly(methyl methacrylate) (PMMA), and PSMMA co-polymer containing silver nanoparticles (AgNPs) using in situ bulk polymerization with and without microwave irradiation (MWI). The AgNPs prepared were embedded within the polymer matrix. A modification in the thermal stability of the PS/Ag, PMMA/Ag, and PSMMA/Ag nanocomposites using MWI and in situ was observed compared with that of neat PSMMA, PS, and PMMA. In particular, PS/Ag, and PSMMA/Ag nanocomposites used in situ showed better thermal stability than MWI, while PMMA/Ag nanocomposites showed improved thermal stability. The electrical conductivity of the PS/Ag, PMMA/Ag, and PSMMA/Ag composites prepared by MWI revealed a percolation behavior when 20% AgNPs were used as a filler, and the conductivity of the nanocomposites increased to 103 S/cm, 33 S/cm, and 40 mS/cm, respectively. This enhancement might be due to the good dispersion of the AgNPs within the polymer matrix, which increased the interfacial interaction between the polymer and AgNPs. The polymer/Ag nanocomposites developed with tunable thermal and electrical properties could be used as conductive materials for electronic device applications.
| S-EPMC5456822 | biostudies-literature
Project description:A green and facile approach has been developed for the large-scale synthesis of nanosheets of reduced graphene oxide (rGO) and nitrogenated reduced graphene oxide (N-rGO). This has been achieved by direct thermal decomposition of sucrose and glycine at 475 °C in ca. 7 minutes, respectively. The present protocols for synthesizing rGO and N-rGO are simple and environmentally friendly as we do not use any harmful reagents, metal catalysts and solvents. Along with that, this method offers an inexpensive route with high yields to prepare rGO with a high nitrogen content (20-25 atom %). To further improve the properties of the synthesized rGO sheets, hydrogen treatment has been carried out to reduce the oxygen functional groups. Cyclic voltammograms and charge-discharge experiments have been carried out to understand the supercapacitor behavior of rGO and hydrogen treated (H-rGO) samples.
| S-EPMC6964660 | biostudies-literature
Project description:Matrix metalloproteinases (MMP) are key players in the remodelling of the extracellular matrix under physiological and pathological conditions. Thermodynamic parameters of human recombinant metalloproteinases of the active (rMMP2, 3, 7, 8 and 9) and latent (rPro-MMP2, 3 and 9) forms were obtained by differential scanning calorimetry (DSC). Temperature by itself does not result in autocatalysis of recombinant MMP. The transitions observed by DSC correspond to structural domains of the monomeric protein. In this study, we show the domain organization of these proteins, where the thermal transition (Tm) of the main component is observed at 71.3 °C (ProMMP-2); 74.8 °C (ProMMP-8); 80.0 °C (ProMMP-3); 92.6 °C (ProMMP-9) and 98.3 °C (ProMMP-7). For MMP-3, this main Tm is related to the catalytic domain (CD). The isolated recombinant CD of MMP-3 unfolds as a single transition at Tm 83.4 °C, matching the more stable domain observed in the full-length active form of rMMP-3. The denaturation profile of rProMMP-3 shows the main transition at Tm 80 °C, a less stable domain before the propeptide domain (PD) cleavage. Our results indicate that the structural stability of MMP and particularly their CD are not substantially altered after cleavage of the PD. We propose that the thermodynamic parameters obtained by DSC are relevant for the functional study of MMP, particularly to reveal their contribution in complex biological samples in health and disease.
| S-EPMC7205746 | biostudies-literature
Project description:Polystyrene (PS) is widely used in the plastics industry, but the application range of PS is limited due to its inherently high flammability. A variety of two-dimensional (2D) nanomaterials have been reported to impart excellent flame retardancy to polymeric materials. In this study, a 2D nanomaterial MXene-organic hybrid (O-Ti3C2) was applied to PS as a nanofiller. Firstly, the MXene nanosheets were prepared by acid etching, intercalation, and delamination of bulk MAX (Ti3AlC2) material. These exfoliated MXene nanosheets were then functionalized using a cationic surfactant to improve the dispersibility in DMF. Even with a small loading of functionalized O-Ti3C2 (e.g., 2 wt%), the resulting PS nanocomposite (PS/O-Ti3C2) showed good thermal stability and lower flammability evidenced by thermogravimetric analysis (TGA) and pyrolysis-combustion flow calorimetry (PCFC). The peak heat release rate (pHRR) was significantly reduced by 32% compared to the neat PS sample. In addition, we observed that the temperature at pHRR (TpHRR) shifted to a higher temperature by 22 °C. By comparing the TGA and PCFC results between the PS/MAX and different weight ratios of PS/O-Ti3C2 nanocomposites, the thermal stability and 2D thermal- and mass-transfer barrier effect of MXene-organic hybrid nanosheets were revealed to play essential roles in delaying the polymer degradation.
| S-EPMC8954563 | biostudies-literature
Project description:Copper matrix composites have a wide application as magnetic conductive materials, electromagnetic materials, electrical discharge machining materials, etc. Such materials are expected to have a good combination of excellent electrical conductivity and good mechanical strength. In this work, micro/nano hybrid reinforcements with Fe microspheres and reduced graphene oxide (rGO) nanosheets were developed for copper matrix composites. The rGO/Fe/Cu powders were firstly wet-mixed and then densified by the vacuum hot-pressing sintering to obtain the bulk compacts. Microstructure, electrical conductivity and mechanical properties of such compacts were investigated. Microstructural result of as-sintered compacts shows that the Fe microspheres could distribute in the matrix uniformly, and rGO nanosheets exhibit both agglomerated and dispersed states. The grain size of Cu matrix decreased with the increase of the rGO content. Hardness, compression and tensile 0.2% yield strength of the as-sintered compacts were improved evidently by the addition of the hybrid Fe/rGO, comparing with pure Cu and single Fe-added composites. However, a lower electrical conductivity appeared in the more rGO-added composites, but still reached more than 33.0% international annealing copper standard (IACS). These performance change could be sought in the spatially geometrical distribution and characteristics of such micro/nano Fe/rGO hybrid addition, and the relevant mechanisms were discussed.
| S-EPMC9573056 | biostudies-literature
Project description:Pecan bacterial leaf scorch caused by Xylella fastidiosa is an emerging disease for the U.S. and international pecan industries and can be transmitted from scion to rootstock via grafting. With the expanse of global transportation and trade networks, phytosanitation is critical for reducing the spread of economically significant pathogens, such as X. fastidiosa. We developed and evaluated thermal treatments using microwave irradiation and microwave absorbers [sterile deionized water (dH2O) and carbon nanotubes (CNTs)] as novel disinfectant methods for remediating X. fastidiosa in pecan scions. Partial submergence of scions in dH2O or CNT dispersions resulted in the transport of microwave absorbers in the xylem tissue via transpiration but did not compromise plant health. The microwave absorbers effectively transferred heat to the scion wood to reach an average temperature range of 55-65°C. Microwave radiation exposure for 6 sec (3 sec for two iterations) of CNT- or dH2O-treated scions reduced the frequency of X. fastidiosa-positive in pecan scions without negatively affecting plant viability when compared to the control group (dH2O-treated with no microwave). The efficacy of the new thermal treatments based on microwave irradiation was comparable to the conventional hot-water treatment (HWT) method, in which scions were submerged in 46°C water for 30 min. Microwave irradiation can be employed to treat X. fastidiosa-infected scions where the conventional HWT treatment is not feasible. This study is the first report to demonstrate novel thermal treatment methods based on the microwave irradiation and microwave absorbers of dH2O and CNT as an application for the phytosanitation of xylem-inhabiting bacteria in graftwood.
| S-EPMC7816998 | biostudies-literature
Project description:A novel aromatic diamine containing pyridyl side group, 4-pyridine-4,4-bis(3,5-dimethyl-5-aminophenyl)methane (PyDPM), was successfully synthesized via electrophilic substitution reaction. The polyimides (PIs) containing pyridine were obtained via the microwave-assisted one-step polycondensation of the PyDPM with pyromellitic dianhydride (PMDA), 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), 3,3',4,4'-diphenylether tetracarboxylic dianhydride (ODPA) and 4,4'-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). Contrarily to the reported similar PIs, these PIs exhibit much higher thermal stability or heat resistance, i.e. high glass transition temperatures (T gs) in the range of 358-473°C, and the decomposition temperatures at 5% weight loss over 476°C under nitrogen. They can afford flexible and strong films with tensile strength of 82.1-93.3 MPa, elongation at break of 3.7%-15.2%, and Young's modulus of 3.3-3.8 GPa. Furthermore, The PI films exhibit good optical transparency with the cut-off wavelength at 313-366 nm and transmittance higher than 73% at 450 nm. The excellent thermal and optical transmittance can be attributed to synthesis method and the introduction of pyridine rings and ortho-methyl groups. The inherent viscosities of PIs via one-step method were found to be 0.58-1.12 dl g-1 in DMAc, much higher than those via two-step method. These results indicate these PIs could be potential candidates for optical substrates of organic light emitting diodes (OLEDs).
| S-EPMC6599801 | biostudies-literature
Project description:Recently, there is a need to explore the utilization of various heterostructures using the designed nanocomposites and tuning the surfaces of electrodes for improving the electrochemical performance of supercapacitors (SC). In this work, a novel approach is successfully employed through a facile two-step synthetic route with the assistance of a microwave for only 1 min. Depending on the glass transition of a polystyrene (PS) substrate and electrochemical deposition (ECD) of electroactive Ni-Co layered double hydroxides (LDHs), a hierarchically designed flake-like morphology can be readily prepared to enhance the surface-active sites, which allows a rhombohedral Ni-Co LDHs electrode to obtain superior electrochemical properties. Further, the interactions between electrode and electrolyte during the diffusion of ions are highly simplified using multiple enhanced electroactive sites and shorter pathways for electron transfer. The unique surface architecture of the PS substrate and the synergistic effect of the bimetallic components in Ni-Co LDHs enable this substrate to obtain desired electrochemical activity in charge storage systems. The optimized MWC Co0.5Ni0.5 electrode exhibited an areal capacity of 100 µAh/cm2 at a current density of 1 mA/cm2 and a remarkable capacity retention of 91.2% over 5000 continuous charging and discharging cycles due to its remarkable synergistic effect of abundant faradaic redox reaction kinetics. The HSC device is assembled with the combination of optimized MWC Co0.5Ni0.5 and activated carbon as a positive and negative electrode, respectively. Further, the electrochemical test results demonstrated that MWC Co0.5Ni0.5 //AC HSC device showed a high areal capacitance of 531.25 mF/cm2 at a current density of 5 mA/cm2. In addition, the fabricated an aqueous HSC device showed a power density of 16 mW/cm2 at an energy density of 0.058 mWh/cm2, along with the remarkable capacity retention of 82.8% even after 10,000 continuous charging and discharging cycles. Moreover, the assembled hybrid supercapacitor (HSC) device is integrated with a triboelectric nanogenerator (TENG) for the development of energy conversion and storage systems. Not only an extensive survey of materials but also an innovative solution for recent progress can confirm the wide range of potential SC applications. Remarkably, this study is a new way of constructing self-powered energy storage systems in the field of sustainable wearable electronics and future smart sensing systems.
| S-EPMC9864052 | biostudies-literature
Project description:As known, radiation therapy (RT) can exacerbate the degree of hypoxia of tumor cells, which induces serious resistance to RT and in turn, is the greatest obstacle to RT. Reoxygenation can restore the hypoxic state of tumor cells, which plays an important role in reshaping tumor microenviroment for achieving optimal therapeutic efficacy. Herein, we report for the first time that microwave (MW)-triggered IL-Quercetin-CuO-SiO2@ZrO2-PEG nanosuperparticles (IQuCS@Zr-PEG NSPs) have been used to achieve an optimal RT therapeutic outcomes by the strategy of upregulating tumor reoxygenation, i.e. hypoxic cells acquire oxygen and return to normal state. Methods: We prepared a promising multifunctional nanosuperparticle to upregulate tumor reoxygenation by utilizing CuO nanoparticle to generate oxygen under MW irradiation in the tumor microenvironment. The IQuCS@Zr-PEG NSPs were obtained by introducing CuO nanoparticles, MW sensitizer of 1-butyl-3-methylimidazolium hexafluorophosphate (IL), radiosensitizer of Quercetin (Qu) and surface modifier of monomethoxy polyethylene glycol sulfhyl (mPEG-SH, 5k Da) into mesoporous sandwich SiO2@ZrO2 nanosuperparticles (SiO2@ZrO2 NSPs). The release oxygen by IQuCS@Zr-PEG NSPs under MW irradiation was investigated by a microcomputer dissolved oxygen-biochemical oxygen demand detector (DO-BOD) test. Finally, we used the 99mTc-HL91 labeled reoxygenation imaging, Cellular immunofluorescence, immunohistochemistry, and TUNEL experiments to verify that this unique MW-responsive reoxygenation enhancer can be used to stimulate reshaping of the tumor microenvironment. Results: Through experiments we found that the IQuCS@Zr-PEG NSPs can persistently release oxygen under the MW irradiation, which upregulates tumor reoxygenation and improve the combined tumor treatment effect of RT and microwave thermal therapy (MWTT). Cellular immunofluorescence and immunohistochemistry experiments demonstrated that the IQuCS@Zr-PEG NSPs can downregulate the expression of hypoxia-inducible factor 1α (HIF-1α) under MW irradiation. The 99mTc-HL91 labeled reoxygenation imaging experiment also showed that the oxygen generated by IQuCS@Zr-PEG NSPs under MW irradiation can significantly increase the reoxygenation capacity of tumor cells, thus reshaping the tumor microenvironment. The high inhibition rate of 98.62% was achieved in the antitumor experiments in vivo. In addition, the IQuCS@Zr-PEG NSPs also had good computed tomography (CT) imaging effects, which can be used to monitor the treatment of tumors in real-time. Conclusions: The proof-of-concept strategy of upregulating tumor reoxygenation is achieved by MW triggered IQuCS@Zr-PEG NSPs, which has exhibited optimal therapeutic outcomes of combination of RT and MWTT tumor. Such unique MW-responsive reoxygenation enhancer may stimulate the research of reshaping tumor microenvironment for enhancing versatile tumor treatment.
| S-EPMC7150478 | biostudies-literature
Project description:An understanding of the structural and compositional
| S-EPMC9972340 | biostudies-literature