Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Preparation and Characterization of Bioplastic-Based Green Renewable Composites from Tapioca with Acetyl Tributyl Citrate as a Plasticizer.

ABSTRACT: Granular tapioca was thermally blended with poly(lactic acid) (PLA). All blends were prepared using a plasti-corder and characterized for tensile properties, thermal properties and morphology. Scanning electron micrographs showed that phase separation occurred, leading to poor tensile properties. Therefore, methylenediphenyl diisocyanate (MDI) was used as an interfacial compatibilizer to improve the mechanical properties of PLA/tapioca blends. The addition of MDI could improve the tensile strength of the blend with 60 wt% tapioca, from 19.8 to 42.6 MPa. In addition, because PLA lacked toughness, acetyl tributyl citrate (ATBC) was added as a plasticizer to improve the ductility of PLA. A significant decrease in the melting point and glass-transition temperature was observed on the basis of differential scanning calorimetry, which indicated that the PLA structure was not dense after ATBC was added. As such, the brittleness was improved, and the elongation at break was extended to several hundred percent. Therefore, mixing ATBC with PLA/tapioca/MDI blends did exhibit the effect of plasticization and biodegradation. The results also revealed that excessive plasticizer would cause the migration of ATBC and decrease the tensile properties.

SUBMITTER: Tsou CH

PROVIDER: S-EPMC5456173 | biostudies-other | 2014 Aug

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Preparation and Characterization of Electrospun Collagen Based Composites for Biomedical Applications.

Project description:Electrospinning is a widely used technology for obtaining nanofibers from synthetic and natural polymers. In this study, electrospun mats from collagen (C), polyethylene terephthalate (PET) and a blend of the two (C-PET) were prepared and stabilized through a cross-linking process. The aim of this research was to prepare and characterize the nanofiber structure by Fourier-transform infrared with attenuated total reflectance spectroscopy (FTIR-ATR) in close correlation with dynamic vapor sorption (DVS). The studies indicated that C-PET nanofibrous mats shows improved mechanical properties compared to collagen samples. A correlation between morphological, structural and cytotoxic proprieties of the studied samples were emphasized and the results suggest that the prepared nanofiber mats could be a promising candidate for tissue-engineering applications, especially dermal applications.

| S-EPMC7559754 | biostudies-literature

Preparation and Characterization of Polyvinylpyrrolidone/Cellulose Nanocrystals Composites.

Project description:Composite films and aerogels of polyvinylpyrrolidone/cellulose nanocrystals (PVP/CNC) were prepared by solution casting and freeze-drying, respectively. Investigations into the PVP/CNC composite films and aerogels over a wide composition range were conducted. Thermal stability, morphology, and the resulting reinforcing effect on the PVP matrix were explored. FTIR, TGA, DSC, X-ray diffraction, SEM, and tensile testing were used to examine the properties of the composites. It was revealed PVP-assisted CNC self-assembly that produces uniform CNC aggregates with a high aspect ratio (length/width). A possible model of the PVP-assisted CNC self-assembly has been considered. Dispersibility of the composite aerogels in water and some organic solvents was studied. It was shown that dispersing the composite aerogels in water resulted in stable colloidal suspensions. CNC particles size in the redispersed aqueous suspensions was near similar to the CNC particles size in never-dried CNC aqueous suspensions.

| S-EPMC6315985 | biostudies-literature

Preparation and Characterization of Silicon-Metal Fluoride Reactive Composites.

Project description:Fuel-rich composite powders combining elemental Si with the metal fluoride oxidizers BiF3 and CoF2 were prepared by arrested reactive milling. Reactivity of the composite powders was assessed using thermoanalytical measurements in both inert (Ar) and oxidizing (Ar/O2) environments. Powders were ignited using an electrically heated filament; particle combustion experiments were performed in room air using a CO2 laser as an ignition source. Both composites showed accelerated oxidation of Si when heated in oxidizing environments and ignited readily using the heated filament. Elemental Si, used as a reference, did not exhibit appreciable oxidation when heated under the same conditions and could not be ignited using either a heated filament or laser. Lower-temperature Si fluoride formation and oxidation were observed for the composites with BiF3; respectively, the ignition temperature for these composite powders was also lower. Particle combustion experiments were successful with the Si/BiF3 composite. The statistical distribution of the measured particle burn times was correlated with the measured particle size distribution to establish the effect of particle sizes on their burn times. The measured burn times were close to those measured for similar composites with Al and B serving as fuels.

| S-EPMC7760387 | biostudies-literature

Preparation and Characterization of Zeolite/TiO? Cement-Based Composites with Excellent Photocatalytic Performance.

Project description:A zeolite/TiO? composite (ZTC) was applied to prepare a high-quality photocatalytic cement-based material (PCM). The acetone degradation experiment and micro measurements including XRD(X-Ray Diffractometer), SEM-EDS(Scanning Electron Microscope-Energy Dispersive Spectrometer), BET(BET Specific Surface Area Tester), FTIR(Fourier Transform Infrared Spectrometer) were conducted to characterize the photocatalytic efficiency and physicochemical properties of PCM, respectively. Results show that TiO? particles disperse on the surface of a PCM homogeneously and provide abundant active sites for photocatalytic reactions. Compared to a normal photocatalytic cement-based material (NPCM), the TiO? content of a PCM is lower and its photocatalytic efficiency is higher. The ZTC frees TiO? particles from the impacts of cement hydration products and increases the adsorption volume of acetone. The photocatalytic performance of the PCM was stable after repeated tests. Using the ZTC as a photocatalyst has a prominent effect on the photocatalytic performance of the PCM.

| S-EPMC6316990 | biostudies-other

Renewable Beta-Elemene Based Cyclic Carbonates for the Preparation of Oligo(hydroxyurethane)s.

Project description:Conversion of β-elemene into new β-elemene dicarbonates through epoxidation and halide salt-catalyzed CO2 cycloaddition reactions is reported. Step-growth polyaddition of this dicarbonate to five different, commercial diamines was investigated under neat conditions at 150 °C yielding non-isocyanate-based low molecular weight oligo(hydroxyurethane)s with 1.3≤Mn ≤6.3 kDa and 1.3≤Ð≤2.1, and with glass transition temperatures ranging from -59 to 84 °C. The preparation of one selected polyhydroxyurethane material, obtained in the presence of Jeffamine® D-2010 was scaled-up to 43 g. The latter, when combined in a formulation using Irgacure® 2100 and Laromer® LR 9000 allowed the preparation of coatings that were analyzed with several techniques showing the potential of these biobased oligourethanes towards the preparation of commercially relevant materials.

| S-EPMC9541927 | biostudies-literature

Preparation, characterization, electrical conductivity, and life cycle assessment of carbon nanofibers-reinforced Ecuadorian natural zeolite-based geopolymer composites.

Project description:Geopolymers are inorganic crosslinked polymers with much less carbon footprint than ordinary Portland cement. Geopolymers and geopolymer-based materials have superior mechanical and durability properties with extreme thermal and chemical resistance. Carbon nano- or microfibers-reinforced geopolymers show potential properties such as electric conductivity, enhanced mechanical and thermal stability, and multi-functionality. This study evaluated the effect of incorporating carbon nanofibers in natural zeolite-based geopolymers and their impact on the mechanical, thermal, and electric conductivity of yielded geopolymer composites. Additionally, a life cycle assessment for 1 m3 geopolymer and its carbon fiber reinforced geopolymers' production has been conducted to evaluate the environmental impact of the processes.

| S-EPMC10957430 | biostudies-literature

Sample preparation under turbulent flow with renewable sorbent.

Project description:Turbulent flow chromatography is an online solid phase extraction mode that achieves the extraordinary effect of proxying an upper molecular weight cutoff for the retained molecules, based on loading the sample at high linear velocities. Despite the potential of being a universal sample preparation technique prior to inductively coupled plasma mass spectrometry and liquid chromatography mass spectrometry, it employs specific hardware and expensive consumables. In the present work we apply this technique using off-the-shelf fluidic components and the niche "bead injection" methodology. For the first time, this procedure has been executed with a pressure of approximately 20 bar, compared to the low pressure of the classic setup, achieving a sample throughput >285 h-1 for the SPE/TFC procedure, or 20 h-1 if the procedure involves renewing the sorbent, using no more than 4 mg of sorbent for every μ-SPE. Another novelty is that sorbent packing and unpacking has been controlled with a smart method using real-time pressure feedback as quality control for truly unattended operation. Finally, the turbulent flow chromatography principle has been comprehensively characterized, providing similar performance to that demonstrated in earlier literature, and the ancillary sample preparation capabilities, e.g., in-valve acidification, have been demonstrated by the fractionation of gadolinium in surface waters prior to ICP-MS, an element of increasing surface water concern due to its use as a magnetic resonance contrast agent.

| S-EPMC8565614 | biostudies-literature

Green Nephrology: Citrate, the Green Alternative to Heparin in Hemodialysis.

Project description: Not available

| S-EPMC10851001 | biostudies-literature

Reply to: Acetyl-CoA is produced by the citrate synthase homology module of ATP-citrate lyase.

Project description: Not available

| S-EPMC8427657 | biostudies-literature

Preparation of Bio-Based Polyamide Elastomer by Using Green Plasticizers.

Project description:The purpose of this work was to study the effects of three green plasticizers H?O, glycerol, and soybean oil, on the properties of bio-based BDIS polyamides. The BDIS polyamides synthesized from the following biomass monomers: 1,4-butanediamine (BD), 1,10-decanediamine (DD), itaconic acid (IA), and sebacic acid (SA). It is interesting to note that the amorphous BDIS (IA-80%) polyamide was changed from the glassy state to the rubbery state after water soaking and induced crystallization at the same time. The H?O-plasticized non-crosslinked BDIS (IA-80%) polyamides can be very useful for the preparation of physical water gel. The glycerol- and soybean oil-plasticized BDIS (IA-80%) polyamides displayed excellent toughness. The plasticized BDIS (IA-80%) polyamides were characterized by Fouriertransform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), mechanical testing, and X-ray diffraction (XRD).

| S-EPMC6432398 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data