Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Microstructured Polymer Blend Surfaces Produced by Spraying Functional Copolymers and Their Blends.

ABSTRACT: We described the fabrication of functional and microstructured surfaces from polymer blends by spray deposition. This simple technique offers the possibility to simultaneously finely tune the microstructure as well as the surface chemical composition. Whereas at lower polymer concentration, randomly distributed surface micropatterns were observed, an increase of the concentration leads to significant changes on these structures. On the one hand, using pure homopolystyrene fiber-like structures were observed when the polymer concentration exceeded 30 mg/mL. Interestingly, the incorporation of 2,3,4,5,6-pentafluorostyrene changed the morphology, and, instead of fibers, micrometer size particles were identified at the surface. These fluorinated microparticles provide superhydrophobic properties leading to surfaces with contact angles above 165°. Equally, in addition to the microstructures provided by the spray deposition, the use of thermoresponsive polymers to fabricate interfaces with responsive properties is also described. Contact angle measurements revealed variations on the surface wettability upon heating when blends of polystyrene and polystyrene-b-poly(dimethylaminoethyl methacrylate) are employed. Finally, the use of spraying techniques to fabricate gradient surfaces is proposed. Maintaining a constant orientation, the surface topography and thus the contact angle varies gradually from the center to the edge of the film depending on the spray angle.

SUBMITTER: Vargas-Alfredo N

PROVIDER: S-EPMC5456787 | biostudies-other | 2016 May

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Bioinspired Microstructured Polymer Surfaces with Antireflective Properties.

Project description:Over the years, different approaches to obtaining antireflective surfaces have been explored, such as using index-matching, interference, or micro- and nanostructures. Structural super black colors are ubiquitous in nature, and biomimicry thus constitutes an interesting way to develop antireflective surfaces. Moth-eye nanostructures, for example, are well known and have been successfully replicated using micro- and nanofabrication. However, other animal species, such as birds of paradise and peacock spiders, have evolved to display larger structures with antireflective features. In peacock spiders, the antireflective properties of their super black patches arise from relatively simple microstructures with lens-like shapes organized in tightly packed hexagonal arrays, which makes them a good candidate for cheap mass replication techniques. In this paper, we present the fabrication and characterization of antireflective microarrays inspired by the peacock spider's super black structures encountered in nature. Firstly, different microarrays 3D models are generated from a surface equation. Secondly, the arrays are fabricated in a polyacrylate resin by super-resolution 3D printing using two-photon polymerization. Thirdly, the resulting structures are inspected using a scanning electron microscope. Finally, the reflectance and transmittance of the printed structures are characterized at normal incidence with a dedicated optical setup. The bioinspired microlens arrays display excellent antireflective properties, with a measured reflectance as low as 0.042 ± 0.004% for normal incidence, a wavelength of 550 nm, and a collection angle of 14.5°. These values were obtained using a tightly-packed array of slightly pyramidal lenses with a radius of 5 µm and a height of 10 µm.

| S-EPMC8470586 | biostudies-literature

Epitaxy-Directed Self-Assembly of Copolymers and Polymer Blends.

Project description:Directed self-assembly of materials into patterned structures is of great importance since the performance of them depends remarkably on their multiscale hierarchical structures. Therefore, purposeful structural regulation at different length scales through crystallization engineering provides an opportunity to modify the properties of polymeric materials. Here, an epitaxy-directed self-assembly strategy for regulating the pattern structures including phase structure as well as crystal modification and orientation of each component for both copolymers and polymer blends is reported. Owing to the specific crystallography registration between the depositing crystalline polymers and the underlying crystalline substrate, not only order phase structure with controlled size at nanometer scale but also the crystal structure and chain orientation of each component within the separated phases for both copolymers and polymer blend systems can be precisely regulated.

| S-EPMC10787078 | biostudies-literature

Photoinduced Degradation of Polymer Films Using Polyglyoxylate-Polyester Blends and Copolymers.

Project description:Polymeric coatings are commonly employed to alter surface properties. While some coatings are designed to remain stable over a prolonged period, in applications such as pharmaceuticals or fertilizers, the coating is designed to erode and reveal or release the underlying material. Self-immolative polymers (SIPs) undergo depolymerization following the cleavage of stimuli-responsive end-caps from their termini, enabling controlled depolymerization in the solid state and in solution. Poly(ethyl glyoxylate) (PEtG) is a promising SIP because of its depolymerization to benign products, but its amorphous structure and low glass-transition temperature make it unsuitable alone for coating applications. This study explored the blending of PEtG with polyesters including polycaprolactone (PCL), poly(l-lactic acid), and poly(R-3-hydroxybutyrate). Block copolymers of PEtG with PCL were also synthesized and studied. It was found that the phase separation behavior and consequently the thermal and mechanical properties of the materials could be tuned according to the composition of the blend, while the stimuli-responsive degradation of PEtG was retained in the blends. This work therefore provides a framework for the application of PEtG-based coatings in applications ranging from pharmaceuticals to agricultural products.

| S-EPMC6643861 | biostudies-literature

Wetting morphologies at microstructured surfaces.

Project description:The wetting of microstructured surfaces is studied both experimentally and theoretically. Even relatively simple surface topographies such as grooves with rectangular cross section exhibit a large variety of different wetting morphologies as observed by atomic force microscopy. This polymorphism arises from liquid wedge formation along the groove corners and from contact line pinning along the groove edges. A global morphology diagram is derived that depends only on two system parameters: (i) the aspect ratio of the groove geometry and (ii) The contact angle of the underlying substrate material. For microfluidics, the most interesting shape regimes involve extended liquid filaments, which can grow and shrink in length while their cross section stays essentially constant. Thus, any method by which one can vary the contact angle can be used to switch the length of the filament, as is demonstrated in the context of electrowetting.

| S-EPMC546015 | biostudies-literature

Bubble nucleation and growth on microstructured surfaces under microgravity.

Project description:Understanding the dynamics of surface bubble formation and growth on heated surfaces holds significant implications for diverse modern technologies. While such investigations are traditionally confined to terrestrial conditions, the expansion of space exploration and economy necessitates insights into thermal bubble phenomena in microgravity. In this work, we conduct experiments in the International Space Station to study surface bubble nucleation and growth in a microgravity environment and compare the results to those on Earth. Our findings reveal significantly accelerated bubble nucleation and growth rates, outpacing the terrestrial rates by up to ~30 times. Our thermofluidic simulations confirm the role of gravity-induced thermal convective flow, which dissipates heat from the substrate surface and thus influences bubble nucleation. In microgravity, the influence of thermal convective flow diminishes, resulting in localized heat at the substrate surface, which leads to faster temperature rise. This unique condition enables quicker bubble nucleation and growth. Moreover, we highlight the influence of surface microstructure geometries on bubble nucleation. Acting as heat-transfer fins, the geometries of the microstructures influence heat transfer from the substrate to the water. Finer microstructures, which have larger specific surface areas, enhance surface-to-liquid heat transfer and thus reduce the rate of surface temperature rise, leading to slower bubble nucleation. Our experimental and simulation results provide insights into thermal bubble dynamics in microgravity, which may help design thermal management solutions and develop bubble-based sensing technologies.

| S-EPMC10827752 | biostudies-literature

Reversible Binding Interfaces Made of Microstructured Polymer Brushes.

Project description:The polymer brush architecture of the end-tethered polymer molecules is one of the most widely used efficient methods to regulate interfacial interactions in colloidal systems found in live matter and manufactured materials. Emerging applications of polymer brush structures require solutions to new tasks in the control of interfacial interactions. The rapid development of live cell manufacturing relies on scalable and efficient cell harvesting methods. Stimuli-responsive surfaces made of surface-grafted poly(N-isopropylacrylamide) (PNIPAM) can bind and detach the adherent cell upon changes in temperature and have been used for cell growth and harvesting. The applications are limited by the requirement to satisfy a range of PNIPAM coating characteristics that depend on the dimensions of the integrin complex in the cell membrane and the basal surface. The analysis of the microstructured surfaces, when adhesive and disjoining functions of the microdomains are decoupled, shows that many limitations of PNIPAM one-component coatings can be avoided by using a much broader range of structural characteristics of the microstructured interfaces composed of alternating disjoining PNIPAM domains and adhesive polymeric domains with cell-affinity functional groups. Temperature-controlled reversible adhesion to such microstructured interfaces is studied here experimentally with model systems of solid spherical particles and by employing simulations for solid and soft membranes interacting with the microstructured surfaces to mimic interactions with soft and solid disk-like particles.

| S-EPMC10993409 | biostudies-literature

Lysozyme release and polymer erosion behavior of injectable implants prepared from PLGA-PEG block copolymers and PLGA/PLGA-PEG blends.

Project description:PurposeWe evaluated the controlled release of lysozyme from various poly(D,L-lactic-co-glycolic acid) (PLGA) 50/50-polyethylene glycol (PEG) block copolymers relative to PLGA 50/50.MethodsLysozyme was encapsulated in cylindrical implants (0.8 mm diameter) by a solvent extrusion method. Release studies were conducted in phosphate buffered saline +0.02% Tween 80 (PBST) at 37°C. Lysozyme activity was measured by a fluorescence-based assay. Implant erosion was evaluated by kinetics of polymer molecular weight decline, water uptake, and mass loss.ResultsLysozyme release from an AB15 di-block copolymer (15% 5 kDa PEG, PLGA 28 kDa) was very fast, whereas an AB10 di-block copolymer (with 10% 5 kDa PEG, PLGA 45 kDa) and ABA10 tri-block copolymer (with 10% 6 kDa PEG, PLGA 27 kDa) showed release profiles similar to PLGA. We achieved continuous lysozyme release for up to 4 weeks from AB10 and ABA10 by lysozyme co-encapsulation with the pore-forming and acid-neutralizing MgCO3, and from AB15 by co-encapsulation of MgCO3 and blending AB15 with PLGA. Lysozyme activity was mostly recovered during 4 weeks.ConclusionsThese block co-polymers may have utility either alone or as PLGA blends for the controlled release of proteins.

| S-EPMC3930621 | biostudies-literature

Polymer Blends for Improved CO2 Capture Membranes.

Project description:We investigated the possibility of improving the performance of polysulfone (PSf) membranes to be used in carbon dioxide capture devices by blending PSf with a commercial polyethylene imine, Lupasol G20, previously modified with benzoyl chloride (mG20). Additive amount ranged between 2 and 20 wt %. Membranes based on these blends were prepared by phase inversion precipitation and exhibited different morphologies with respect to neat PSf. Surface roughness, water contact angles, and water uptake increased with mG20 content. Mass transfer coefficient was also increased for both N2 and CO2; however, this effect was more evident for carbon dioxide. Carbon dioxide absorption performance of composite membranes was evaluated for potassium hydroxide solution in a flat sheet membrane contactor (FSMC) in cross flow module at different liquid flow rates. We found that, at the lowest flow rate, membranes exhibit a very similar behaviour to neat PSf; nevertheless, significant differences can be found at higher flow rates. In particular, the membranes with 2 and 5 wt % additive behave more efficiently than neat PSf. In contrast, 10 and 20 wt % additive content has an adverse effect on CO2 capture when compared with neat PSf. In the former case, a combination of additive chemical affinity to CO2 and membrane porosity can be claimed; in the latter case, the remarkably higher wettability and water uptake could determine membrane clogging and consequent loss of efficiency in the capture device.

| S-EPMC6835398 | biostudies-literature

Compatibilized Immiscible Polymer Blends for Gas Separations.

Project description:Membrane-based gas separation has attracted a great deal of attention recently due to the requirement for high purity gasses in industrial applications like fuel cells, and because of environment concerns, such as global warming. The current methods of cryogenic distillation and pressure swing adsorption are energy intensive and costly. Therefore, polymer membranes have emerged as a less energy intensive and cost effective candidate to separate gas mixtures. However, the use of polymeric membranes has a drawback known as the permeability-selectivity tradeoff. Many approaches have been used to overcome this limitation including the use of polymer blends. Polymer blending technology synergistically combines the favorable properties of different polymers like high gas permeability and high selectivity, which are difficult to attain with a single polymer. During polymer mixing, polymers tend to uncontrollably phase separate due to unfavorable thermodynamics, which limits the number of completely miscible polymer combinations for gas separations. Therefore, compatibilizers are used to control the phase separation and to obtain stable membrane morphologies, while improving the mechanical properties. In this review, we focus on immiscible polymer blends and the use of compatibilizers for gas separation applications.

| S-EPMC5509093 | biostudies-literature

Improved tumor targeting of polymer-based nanovesicles using polymer-lipid blends.

Project description:Block copolymer-based vesicles have recently garnered a great deal of interest as nanoplatforms for drug delivery and molecular imaging applications due to their unique structural properties. These nanovesicles have been shown to direct their cargo to disease sites either through enhanced permeability and retention or even more efficiently via active targeting. Here, we show that the efficacy of nanovesicle targeting can be significantly improved when prepared from polymer-lipid blends compared with block copolymer alone. Polymer-lipid hybrid nanovesicles were produced from the aqueous coassembly of the diblock copolymer, poly(ethylene oxide)-block-polybutadiene (PEO-PBD), and the phospholipid, hydrogenated soy phosphatidylcholine (HSPC). The PEG-based vesicles, 117 nm in diameter, were functionalized with either folic acid or anti-HER2/neu affibodies as targeting ligands to confer specificity for cancer cells. Our results revealed that nanovesicles prepared from polymer-lipid blends led to significant improvement in cell binding compared to nanovesicles prepared from block copolymer alone in both in vitro cell studies and murine tumor models. Therefore, it is envisioned that nanovesicles composed of polymer-lipid blends may constitute a preferred embodiment for targeted drug delivery and molecular imaging applications.

| S-EPMC3197750 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data