Microstructure Evolution of HSLA Pipeline Steels after Hot Uniaxial Compression.
Ontology highlight
ABSTRACT:
SUBMITTER: Liu Y
PROVIDER: S-EPMC5457077 | biostudies-other | 2016 Aug
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Body-temperature programmable elastic shape memory hybrids (SMHs) have great potential for the comfortable fitting of wearable devices. Traditionally, shore hardness is commonly used in the characterization of elastic materials. In this paper, the evolution of shore hardness in body-temperature programmable elastic SMHs upon cyclic loading, and during the shape memory cycle, is systematically investigated. Upon cyclic loading, similar to the Mullins effect, significant softening appears, when the applied strain is over a certain value. On the other hand, after programming, in general, the measured hardness increases with increase in programming strain. However, for certain surfaces, the hardness decreases slightly and then increases rapidly. The underlying mechanism for this phenomenon is explained by the formation of micro-gaps between the inclusion and the matrix after programming. After heating, to melt the inclusions, all samples (both cyclically loaded and programmed) largely recover their original hardness.
| S-EPMC9697891 | biostudies-literature
Project description:The chemical, physical, and mechanical properties of the extracellular environment have a strong effect on cell migration. Aspects such as pore size or stiffness of the matrix influence the selection of the mechanism used by cells to propel themselves, including by pseudopods or blebbing. How a cell perceives its environment and how such a cue triggers a change in behavior are largely unknown, but mechanics is likely to be involved. Because mechanical conditions are often controlled by modifying the composition of the environment, separating chemical and physical contributions is difficult and requires multiple controls. Here we propose a simple method to impose a mechanical compression on individual cells without altering the composition of the matrix. Live imaging during compression provides accurate information about the cell's morphology and migratory phenotype. Using Dictyostelium as a model, we observe that a compression of the order of 500 Pa flattens the cells under gel by up to 50%. This uniaxial compression directly triggers a transition in the mode of migration from primarily pseudopodial to bleb driven in <30 s. This novel device is therefore capable of influencing cell migration in real time and offers a convenient approach with which to systematically study mechanotransduction in confined environments.
| S-EPMC5349787 | biostudies-literature
Project description:The Cu-1.7Ni-1.4Co-0.65Si (wt%) alloy is hot compressed by a Gleeble-1500D machine under a temperature range of 760 to 970 °C and a strain rate range of 0.01 to 10 s-1. The flow stress increases with the extension of strain rate and decreases with the rising of deformation temperature. The dynamic recrystallization behavior happens during the hot compression deformation process. The hot deformation activation energy of the alloy can be calculated as 468.5 kJ/mol, and the high temperature deformation constitutive equation is confirmed. The hot processing map of the alloy is established on the basis of hot deformation behavior and hot working characteristics. With the optimal thermal deformation conditions of 940 to 970 °C and 0.01 to 10 s-1, the fine equiaxed grain and no holes are found in the matrix, which can provide significant guidance for hot deformation processing technology of Cu-Ni-Co-Si alloy.
| S-EPMC7254276 | biostudies-literature
Project description:We investigate experimentally and theoretically the sequence of phases that occurs when a self-assembled monolayer of gold nanoparticles supported on a fluid is compressed uniaxially in a Langmuir trough. Uniaxial compression of the monolayer results in the appearance of lines that have been shown to be regions of trilayer. These lines exhibit complex patterns that depend on the extent of compression. We show that these patterns can be understood in terms of an equilibrium statistical mechanical theory, originally developed in the context of commensurate-incommensurate transitions in krypton monolayers adsorbed on graphite, in which there is an energy cost to line deformations and to line intersections. Even though line intersections are energetically costly, they lower the free energy because they cause the entropy of the system to increase when the density of lines is low enough. Our analytic and Monte Carlo analyses of the model demonstrate that the model exhibits two-phase coexistence. Our experimental observations are qualitatively consistent with the predictions of the model.
| S-EPMC3549100 | biostudies-literature
Project description:In this paper, analytical results are compared for the newly developed steels, Fe-Mn-Al-C (X105) and Fe-Mn-Al-Nb-Ti-C (X98), after being hot-rolled and also after undergoing thermomechanical treatment in a Gleeble simulator. These steels have a relatively low density (~6.68 g/cm3) and a content of approx. 11% aluminum. The multistage compression of axisymmetric samples constituting a simulation of the real technological process and hot-rolling performed on a semi-industrial line were carried out using three cooling variants: in water, in air, and after isothermal heating and cooling in water. The temperature at the end of the thermomechanical treatment for all variants was 850 °C. On the basis of detailed structural studies, it was found that the main mechanism for removing the effects of the strain hardening that occurred during the four-stage compression involved the dynamic recrystallization occurring in the first and second stages, the hot formability and dynamic recovery in successive stages of deformation, and the static and/or metadynamic recrystallization that occurred at intervals between individual deformations, as well as after the last deformation during isothermal heating. Analysis of the phase composition and structure allowed us to conclude that the tested steels have an austenitic-ferritic structure with carbide precipitates. Research using scanning and transmission electron microscopy identified ?-(Fe, Mn)3AlC and M7C3 carbides in both the analyzed steels. In addition, complex carbides based on Nb and Ti were identified in X98 steel; (Ti, Nb)C carbides occurred in the entire volume of the material. Slow cooling after thermomechanical treatment influenced the formation of larger ?-carbides at the border of the austenite and ferrite grains than in the case of rapid cooling. The size and morphology of the carbides found in the examined steels was varied. Back-scattered electron diffraction studies showed that wide-angle boundaries dominated in these steels.
| S-EPMC7041428 | biostudies-literature
Project description:To study the variation law of ultrasonic parameters of self-compacting concrete before and after damage under uniaxial compression test conditions, the C30 self-compacting concrete blocks stored for 7 days and 28 days were subjected to ultrasonic nondestructive testing, and the variation law of the sound time, amplitude, and sound velocity before and after the damage of self-compacting concrete blocks was emphatically analyzed. The concrete acoustic detection software was introduced to judge and analyze the abnormal values of the parameters of each measuring point, and the defect distribution map of each test block was obtained. The results showed that after curing the self-compacting concrete test block for 7 days and 28 days, the average value of sound time before and after the failure of each measuring point of the test block is small, and the average value of sound time before the failure is less than that after; the average amplitude after failure is smaller than that before failure, and the amplitude of some measuring points will be smaller than that before. The average sound velocity after failure is less than that before failure, and the internal defects appear and the structure is not dense. This study provides a theoretical basis for the application of ultrasonic detection technology in the field of self-compacting concrete and also provides a practical basis for the stability monitoring and failure warning of self-compacting concrete.
| S-EPMC9267734 | biostudies-literature
Project description:The physical and chemical properties of typical nitrate energetic materials under hydrostatic compression and uniaxial compression were studied using the ReaxFF/lg force field combined with the molecular dynamics simulation method. Under hydrostatic compression, the P-V curve and the bulk modulus (B 0) obtained using the VFRS equation of state show that the compressibility of the three crystals is nitroglycerine (NG) > erythritol tetranitrate (ETN) > 2,3-bis-hydroxymethyl-2,3-dinitro-1,4-butanediol tetranitrate (NEST-1). The a- and c-axis of ETN are easy to compress under the action of hydrostatic pressure, but the b-axis is not easy to compress. The b-axis of NEST-1 is the most compressible, while the a- and c-axis can be compressed slightly when the initial pressure increases and then remains unchanged afterward. The a-, b-, and c-axes of NG all have similar compressibilities. By analyzing the change trend of the main bond lengths of the crystals, it can be seen that the most stable of the three crystals is the N-O bond and the largest change is in the O-NO2 bond. The stability of the C-O bond shows that the NO3 produced by nitrates is not from the C-O bond fracture. Under uniaxial compression, the stress tensor component, the average principal stress, and the hydrostatic pressure have similar trends and amplitudes, indicating that the anisotropy behaviors of the three crystals ETN, NEST-1, and NG are weak. There is no significant correlation between maximum shear stress and sensitivity. The maximum shear stresses τ xy and τ yz of the ETN in the [010] direction are 1.5 GPa higher than τ xz . However, the maximum shear stress of NG shows irregularity in different compression directions, indicating that there is no obvious correlation between the maximum shear stress and sensitivity.
| S-EPMC7391943 | biostudies-literature
Project description:Silica glass has been shown in numerous studies to possess significant capacity for permanent densification under pressure at different temperatures to form high density amorphous (HDA) silica. However, it is unknown to what extent the processes leading to irreversible densification of silica glass in cold-compression at room temperature and in hot-compression (e.g., near glass transition temperature) are common in nature. In this work, a hot-compression technique was used to quench silica glass from high temperature (1100 °C) and high pressure (up to 8 GPa) conditions, which leads to density increase of ~25% and Young's modulus increase of ~71% relative to that of pristine silica glass at ambient conditions. Our experiments and molecular dynamics (MD) simulations provide solid evidences that the intermediate-range order of the hot-compressed HDA silica is distinct from that of the counterpart cold-compressed at room temperature. This explains the much higher thermal and mechanical stability of the former than the latter upon heating and compression as revealed in our in-situ Brillouin light scattering (BLS) experiments. Our studies demonstrate the limitation of the resulting density as a structural indicator of polyamorphism, and point out the importance of temperature during compression in order to fundamentally understand HDA silica.
| S-EPMC4606793 | biostudies-literature
Project description:This study analyzed uniaxial compression strength over time by preparing a homogel specimen from a bio grouting material, a cement-like form produced by environment-friendly microbial reactions. Among chemical grouting methods, the most commonly used method is the Labile Waterglass method. In this study, the homogel uniaxial compressive strength of Labile Waterglass (LW) injection material and that of bio grouting material were measured and analyzed. In order to perform the experiment, a total of 10 types of grouting mixing ratios were prepared by a combination of different materials such as Ordinary Portland Cement, Micro Cement, Bio Grouting Material and Sodium Silicate. They were cured in the air, and their homogel uniaxial compression strengths were measured on days 1, 3, 7 and 28 Based on the test results, it was confirmed that the uniaxial strength of the specimen made with Bio Grouting Material, Ordinary Portland Cement and Micro Cement was increased by more than 30% than that of the specimen only used with Ordinary Portland Cement, as a result of hydrogen-released heat reaction between calcium carbonate, the main ingredient of the bio grouting material, and calcium silicate in the cement. This indicates that the use of 30% bio-grouting material instead of cement in the grouting can be a reasonable mixing ratio to save the use of cement, leading to reduction in CO₂ emission.
| S-EPMC5502896 | biostudies-other
Project description:This data article includes raw data for time-lapse ultrasonic tomography measurements during a uniaxial compression test. Two sets of experimental data are included: first, the ultrasonic tomography (UT) observation (i.e., waveform) data at each 20 MPa axial stress step during the uniaxial loading test; and second, the stress-strain curve of the uniaxial compression test. A numerical model based on the combined finite-discrete element method (FDEM) was used to improve the understanding of the experimental results. The model file and the simulated acoustic emission (AE) data extracted from the simulation results are also included in this article. Data sets presented in this article help to improve understanding of the progressive rock failure process at microscopic and macroscopic scales.
| S-EPMC6128094 | biostudies-literature