Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Transformation-Induced Creep and Creep Recovery of Shape Memory Alloy.

ABSTRACT: If the shape memory alloy is subjected to the subloop loading under the stress-controlled condition, creep and creep recovery can appear based on the martensitic transformation. In the design of shape memory alloy elements, these deformation properties are important since the deflection of shape memory alloy elements can change under constant stress. The conditions for the progress of the martensitic transformation are discussed based on the kinetics of the martensitic transformation for the shape memory alloy. During loading under constant stress rate, temperature increases due to the stress-induced martensitic transformation. If stress is held constant during the martensitic transformation stage in the loading process, temperature decreases and the condition for the progress of the martensitic transformation is satisfied, resulting in the transformation-induced creep deformation. If stress is held constant during the reverse transformation stage in the unloading process, creep recovery appears due to the reverse transformation. The details for these thermomechanical properties are investigated experimentally for TiNi shape memory alloy, which is most widely used in practical applications. The volume fraction of the martensitic phase increases in proportion to an increase in creep strain.

SUBMITTER: Takeda K

PROVIDER: S-EPMC5458963 | biostudies-other | 2012 May

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Transformation-Induced Relaxation and Stress Recovery of TiNi Shape Memory Alloy.

Project description:The transformation-induced stress relaxation and stress recovery of TiNi shape memory alloy (SMA) in stress-controlled subloop loading were investigated based on the local variation in temperature and transformation band on the surface of the tape in the tension test. The results obtained are summarized as follows. (1) In the loading process, temperature increases due to the exothermic martensitic transformation (MT) until the holding strain and thereafter temperature decreases while holding the strain constant, resulting in stress relaxation due to the MT; (2) In the unloading process, temperature decreases due to the endothermic reverse transformation until the holding strain and thereafter temperature increases while holding the strain constant, resulting in stress recovery due to the reverse transformation; (3) Stress varies markedly in the initial stage followed by gradual change while holding the strain constant; (4) If the stress rate is high until the holding strain in the loading and unloading processes, both stress relaxation and stress recovery are large; (5) It is important to take into account this behavior in the design of SMA elements, since the force of SMA elements varies even if the atmospheric temperature is kept constant.

| S-EPMC5453294 | biostudies-other

A jumping shape memory alloy under heat.

Project description:Shape memory alloys are typical temperature-sensitive metallic functional materials due to superelasticity and shape recovery characteristics. The conventional shape memory effect involves the formation and deformation of thermally induced martensite and its reverse transformation. The shape recovery process usually takes place over a temperature range, showing relatively low temperature-sensitivity. Here we report novel Cu-Al-Fe-Mn shape memory alloys. Their stress-strain and shape recovery behaviors are clearly different from the conventional shape memory alloys. In this study, although the Cu-12.2Al-4.3Fe-6.6Mn and Cu-12.9Al-3.8Fe-5.6Mn alloys possess predominantly L2(1) parent before deformation, the 2H martensite stress-induced from L2(1) parent could be retained after unloading. Furthermore, their shape recovery response is extremely temperature-sensitive, in which a giant residual strain of about 9% recovers instantly and completely during heating. At the same time, the phenomenon of the jumping of the sample occurs. It is originated from the instantaneous completion of the reverse transformation of the stabilized 2H martensite. This novel Cu-Al-Fe-Mn shape memory alloys have great potentials as new temperature-sensitive functional materials.

| S-EPMC4754943 | biostudies-literature

Phase transformation evolution in NiTi shape memory alloy under cyclic nanoindentation loadings at dissimilar rates.

Project description:Hysteresis energy decreased significantly as nanocrystalline NiTi shape memory alloy was under triangular cyclic nanoindentation loadings at high rate. Jagged curves evidenced discrete stress relaxations. With a large recovery state of maximum deformation in each cycle, this behavior concluded in several nucleation sites of phase transformation in stressed bulk. Additionally, the higher initial propagation velocity of interface and thermal activation volume, and higher levels of phase transition stress in subsequent cycles explained the monotonic decreasing trend of dissipated energy. In contrast, the dissipated energy showed an opposite increasing trend during triangular cyclic loadings at a low rate and 60 sec holding time after each unloading stage. Due to the isothermal loading rate and the holding time, a major part of the released latent heat was transferred during the cyclic loading resulting in an unchanged phase transition stress. This fact with the reorientation phenomenon explained the monotonic increasing trend of hysteresis energy.

| S-EPMC3861797 | biostudies-other

Origami-inspired thin-film shape memory alloy devices.

Project description:We describe the design and fabrication of miniaturized origami structures based on thin-film shape memory alloys. These devices are attractive for medical implants, as they overcome the opposing requirements of crimping the implant for insertion into an artery while keeping sensitive parts of the implant nearly stress-free. The designs are based on a group theory approach in which compatibility at a few creases implies the foldability of the whole structure. Importantly, this approach is versatile and thus provides a pathway for patient-specific treatment of brain aneurysms of differing shapes and sizes. The wafer-based monolithic fabrication method demonstrated here, which comprises thin-film deposition, lithography, and etching using sacrificial layers, is a prerequisite for any integrated self-folding mechanism or sensors and will revolutionize the availability of miniaturized implants, allowing for new and safer medical treatments.

| S-EPMC8155017 | biostudies-literature

Solute-induced strengthening during creep of an aged-hardened Al-Mn-Zr alloy.

Project description:We examine the precipitation and creep behavior of Al-0.5Mn-0.02Si (at.%) alloys, with and without the L12-forming elements Zr and Er (0.09 and 0.05 at.%, respectively), utilizing isochronal aging experiments as well as compressive and tensile creep tests performed between 275 and 400 °C. The Al-0.5Mn-0.09Zr-0.05Er-0.05Si alloy exhibits an unusually high creep resistance in the peak-aged state, which is significantly better than that observed generally in its Mn-free L12-strengthened counterparts; for example, the creep threshold stresses at 300 °C are 34-37 MPa, about three times higher than those in a Mn-free Al-0.11Zr-0.005Er-0.02Si alloy. Scanning transmission electron microscopy illustrates that nanoscale Al 3 (Zr,Er) L1 2 -precipitates are formed in the dendritic cores and micron-sized Al(Mn,Fe)Si α-precipitates in the inter-dendritic channels. Moreover, the Al(f.c.c.)-matrix remains supersaturated with randomly distributed Mn solute atoms, as determined by atom-probe tomography and electrical conductivity measurements, for months at creep temperatures. Creep experiments on the Zr- and Er-free Al-0.5Mn-0.02Si solid-solution alloy reveal a small primary creep strain, a high apparent stress exponent, na ~9-7, and a threshold-stress-type behavior. After ruling out other possible mechanisms, we provide evidence that the threshold stress in this precipitate-free alloy originates from dislocation/solute elastic interactions leading to a strong drag force exerted on edge dislocations, hindering their ability to climb. The relatively high creep resistance of Al-0.5Mn-0.09Zr-0.05Er-0.05Si is interpreted in terms of the synergy between this solute-induced threshold stress (SITS, from Mn in solid-solution) and the known precipitate-bypass threshold stress (from the L12-nanoprecipitates).

| S-EPMC9565667 | biostudies-literature

35 Hz shape memory alloy actuator with bending-twisting mode.

Project description:Shape Memory Alloy (SMA) materials are widely used as an actuating source for bending actuators due to their high power density. However, due to the slow actuation speed of SMAs, there are limitations in their range of possible applications. This paper proposes a smart soft composite (SSC) actuator capable of fast bending actuation with large deformations. To increase the actuation speed of SMA actuator, multiple thin SMA wires are used to increase the heat dissipation for faster cooling. The actuation characteristics of the actuator at different frequencies are measured with different actuator lengths and results show that resonance can be used to realize large deformations up to 35?Hz. The actuation characteristics of the actuator can be modified by changing the design of the layered reinforcement structure embedded in the actuator, thus the natural frequency and length of an actuator can be optimized for a specific actuation speed. A model is used to compare with the experimental results of actuators with different layered reinforcement structure designs. Also, a bend-twist coupled motion using an anisotropic layered reinforcement structure at a speed of 10?Hz is also realized. By increasing their range of actuation characteristics, the proposed actuator extends the range of application of SMA bending actuators.

| S-EPMC4759690 | biostudies-literature

Shift of Creep Mechanism in Nanocrystalline NiAl Alloy.

Project description:We have examined the effects of temperature, stress, and grain size on the creep process including creep strain, crystal structure, dislocations and diffusions of nanocrystalline NiAl alloy through molecular dynamics simulations. A smaller grain size accelerates the creep process due to the large volume fraction of grain boundaries. Higher temperatures and stress levels also speed up this process in terms of dislocation changes and atom diffusion. In both primary creep and steady-state creep stages, atomic diffusion at the grain boundary could be seen and the dislocation density increased gradually, indicating that the creep mechanism at these stages is Coble creep controlled by grain boundary diffusion while accompanied by dislocation nucleation. When the model enters the tertiary creep stage, it can be observed that the diffusion of atoms in the grain boundary and in the crystal and the dislocation density gradually decreases, implying that the creep mechanisms at this stage are Coble creep, controlled by grain boundary diffusion, and Nabarro-Herring creep, controlled by lattice diffusion.

| S-EPMC6720299 | biostudies-literature

Effects of Cold-Rolling/Aging Treatments on the Shape Memory Properties of Ti49.3Ni50.7 Shape Memory Alloy.

Project description:In this study, the combined effects of strengthening, precipitates, and textures on the shape recovery ability and superelasticity of thermomechanically treated Ti49.3Ni50.7 shape memory alloy (SMA) in both the rolling and transverse directions were studied by experimental measurements and theoretical calculations. Experimental results and theoretical calculations showed that the 300 °C × 100 h aged specimen exhibited the best shape memory effect because it possessed the most favorable textures, highest matrix strength, and most beneficially coherent stress induced by Ti3Ni4 precipitates. The 30% cold-rolled and then 300 °C × 100 h aged specimen exhibited the highest strength and superelasticity; however, its shape recovery ability was not as good as expected because the less favorable textures and the high strength inhibited the movements of dislocations and martensite boundaries. Therefore, to achieve the most optimal shape memory characteristics of Ni-rich TiNi SMAs, the effects of textures, matrix strength, and internal defects, such as Ti3Ni4 precipitates and dislocations, should all be carefully considered and controlled during thermomechanical treatments.

| S-EPMC5551747 | biostudies-other

Sutureless microvascular anastomosis assisted by an expandable shape-memory alloy stent.

Project description:Vascular anastomosis is the highlight of cardiovascular, transplant, and reconstructive surgery, which has long been performed by hand using a needle and suture. However, anastomotic thrombosis occurs in approximately 0.5-10% of cases, which can cause serious complications. To improve the surgical outcomes, attempts to develop devices for vascular anastomosis have been made, but they have had limitations in handling, cost, patency rate, and strength at the anastomotic site. Recently, indwelling metal stents have been greatly improved with precise laser metalwork through programming technology. In the present study, we designed a bare metal stent, Microstent, that was constructed by laser machining of a shape-memory alloy, NiTi. An end-to-end microvascular anastomosis was performed in SD rats by placing the Microstent at the anastomotic site and gluing the junction. The operation time for the anastomosis was significantly shortened using Microstent. Thrombus formation, patency rate, and blood vessel strength in the Microstent anastomosis were superior or comparable to hand-sewn anastomosis. The results demonstrated the safety and effectiveness, as well as the operability, of the new method, suggesting its great benefit for surgeons by simplifying the technique for microvascular anastomosis.

| S-EPMC5524395 | biostudies-literature

Designing for Shape Memory in Additive Manufacturing of Cu-Al-Ni Shape Memory Alloy Processed by Laser Powder Bed Fusion.

Project description:Shape memory alloys (SMAs) are functional materials that are being applied in practically all industries, from aerospace to biomedical sectors, and at present the scientific and technologic communities are looking to gain the advantages offered by the new processing technologies of additive manufacturing (AM). However, the use of AM to produce functional materials, like SMAs, constitutes a real challenge due to the particularly well controlled microstructure required to exhibit the functional property of shape memory. In the present work, the design of the complete AM processing route, from powder atomization to laser powder bed fusion for AM and hot isostatic pressing (HIP), is approached for Cu-Al-Ni SMAs. The microstructure of the different processing states is characterized in relationship with the processing parameters. The thermal martensitic transformation, responsible for the functional properties, is analyzed in a comparative way for each one of the different processed samples. The present results demonstrate that a final post-processing thermal treatment to control the microstructure is crucial to obtain the expected functional properties. Finally, it is demonstrated that using the designed processing route of laser powder bed fusion followed by a post-processing HIP and a final specific thermal treatment, a satisfactory shape memory behavior can be obtained in Cu-Al-Ni SMAs, paving the road for further applications.

| S-EPMC9501362 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data