Chromium(VI) Removal from Aqueous Solution by Magnetite Coated by a Polymeric Ionic Liquid-Based Adsorbent.
Ontology highlight
ABSTRACT:
SUBMITTER: Ferreira TA
PROVIDER: S-EPMC5459042 | biostudies-other | 2017 May
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Polypyrrole-gelatin aerogels, containing magnetic barium ferrite (BaFe) particles, (PPy-G-BaFe) were synthesized by oxidative cryopolymerization and used as adsorbents for the removal of Cr(VI) from aqueous media. The removal was performed at pH 4, which was shown to be the optimal value, due to HCrO4- being the dominant species in these conditions and its more favorable adsorption and reduction compared to CrO42-, present at pH > 4. It was found that the presence of magnetic BaFe particles had no effect on the adsorption performance of PPy aerogels in terms of capacity and kinetics, which was attributed to its relatively low content in the composite. After the adsorption, the presence of chromium in the composites was confirmed by EDX and its electrostatic interaction with the adsorbent was pointed at by vibrational spectroscopy, corresponding to the accepted adsorption mechanism. The adsorption kinetics followed the pseudo-second-order model pointing at chemisorption being the rate-limiting step. The adsorption isotherm data was best fitting with the Temkin model. The maximum adsorption capacity, calculated using the Langmuir model, was 255.8 mg g-1 (the maximum experimental value was 161.6 mg g-1). Additionally, the possibility of Cr(VI) adsorption in the presence of Cl-, Br-, NO3- and SO42- as interfering ions was shown.
| S-EPMC10606301 | biostudies-literature
Project description:This study investigated the effectiveness of ionic liquids (ILs) loaded onto the surface of a polymeric adsorbent (βCD-TDI) grafted with modified magnetic nanoparticles (MNPs) via an analysis of water treatment, which resulted in high removal of selected endocrine-disrupting chemicals (parabens). The syntheses of MNPs, MNP-βCD-TDI, and IL-MNP-βCD-TDI were characterised and compared using Fourier transform infrared (FT-IR) spectroscopy, carbon-hydrogen-nitrogen (CHN) analysis, vibrating sample magnetometry (VSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), the Brunauer-Emmett-Teller (BET) method, thermogravimetric analysis (TGA), and X-ray diffraction (XRD). The results of SEM and TEM indicated that the pore size distribution exhibited mesoporous characteristics with a small surface area (BET analysis: 42.95 m2 g-1). Furthermore, a preliminary sorption experiment demonstrated the ability of IL-MNP-βCD-TDI to enhance not only the sorption capacity, but also the removal of propyl paraben (PP), butyl paraben (BP), and benzyl paraben (ArP). The adsorption process appeared to be pH-dependent, and hence the optimum pH of 6 was selected for a subsequent batch adsorption study of all the studied parabens with an equilibrium time of 80 min. Next, in an attempt to investigate the interactions that occur between the adsorbent and the adsorbates, adsorption kinetics and isotherm studies were performed. All the studied parabens were found to best fit pseudo-second-order kinetics and the Freundlich isotherm with R 2 > 0.98 at room temperature (298 K). The interaction of the host-guest inclusion complex and the π-π interaction between βCD and a selected paraben compound (ArP) were identified by performing 1H nuclear magnetic resonance (NMR), together with ultraviolet-visible (UV-vis) spectroscopic analysis. Finally, the adsorption efficiency of the developed material was practically tested on tap water, drain water, and industrial wastewater, which revealed a significant removal of parabens of up to 60-90% in comparison with a prior analysis.
| S-EPMC9082765 | biostudies-literature
Project description:A large amount of industrial wastewater containing pollutants including toxic dyes needs to be processed prior to its discharge into the environment. Biological materials such as sugarcane bagasse (SB) have been reported for their role as adsorbents to remove the dyes from water. In this study, the residue SB after fermentation was utilized for the dye removal. A combined pretreatment of NaOH and methyltrioctylammonium chloride was given to SB for lignin removal, and the pretreated SB was utilized for cellulase production from Bacillus aestuarii UE25. The strain produced 118 IU mL-1 of endoglucanse and 70 IU mL-1 of β-glucosidase. Scanning electron microscopy and FTIR spectra showed lignin and cellulose removal in fermented SB. This residue was utilized for the adsorption of an azo dye, congo red (CR). The thermodynamic, isotherm and kinetics studies for the adsorption of CR revealed distinct adsorption features of SB. Untreated SB followed Langmuir isotherm, whereas pretreated SB and fermented SB obeyed the Freundlich isotherm model. The pseudo-second-order model fitted well for the studied adsorbents. The results of thermodynamic studies revealed spontaneous adsorption with negative standard free energy values. Untreated SB showed a 90.36% removal tendency at 303.15 K temperature, whereas the adsorbents comprised of pretreated and fermented SB removed about 98.35% and 97.70%, respectively. The study provided a strategy to utilize SB for cellulase production and its use as an adsorbent for toxic dyes removal.
| S-EPMC8622147 | biostudies-literature
Project description:Magnetic polymer microspheres (MPMs) using glycidylmethacrylate (GMA) as a functional monomer were synthesized in the presence of Fe₃O₄ nanoparticles via dispersion polymerization. After polymerization, the magnetic polymer microbeads were modified with ethylenediamine (EDA). The obtained ethylenediamine-functionalized magnetic microspheres (EDA-MPMs) were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), vibrating-sample magnetometer (VSM) and Fourier transform infrared (FT-IR) spectroscopy. Then the EDA-MPMs were applied as adsorbents for the removal of Cr(VI) from aqueous solution. Langmuir equation was appropriate to describe the experimental data. The maximum adsorption capacities obtained from the Langmuir model were 236.9, 242.1 and 253.2 mg/g at 298, 308 and 318 K, respectively. The Cr(VI) adsorption equilibrium was established within 120 min and the adsorption kinetics was compatibly described by the pseudo-second order equation. The thermodynamic parameters (ΔG°, ΔH°, ΔS°) of the sorption process revealed that the adsorption was spontaneous and was an endothermic process. The regeneration study demonstrated that the EDA-MPMs could be repeatedly utilized with no significant loss of adsorption efficiency.
| S-EPMC5458844 | biostudies-literature
Project description:Laboratory experiments suggest that polymeric Cr(III) could exist in aqueous solution for a relative long period of time. However, the occurrence of polymeric Cr(III) has not been reported in environmental media due partially to the lack of method for speciating polymeric Cr. We observed an unknown Cr species during the course of study on speciation of Cr in the leachates of chromated-copper-arsenate (CCA)-treated wood. Efforts were made to identify structure of the unknown Cr species. Considering the forms of Cr existed in the CCA-treated woods, we mainly focused our efforts to determine if the unknown species were polymeric Cr(III), complex of Cr/As or complex of Cr with dissolved organic matter (DOM). In order to evaluate whether polymeric Cr(III) largely exist in wood leachates, high performance liquid chromatography coupled with inductively coupled mass spectrometry (HPLC-ICPMS was used) for simultaneous speciation of monomeric Cr(III), polymeric Cr(III), and Cr(VI). In addition to wood leachates where polymeric Cr (III) ranged from 39.1 to 67.4%, occurrence of the unknown Cr species in other environmental matrices, including surface waters, tap and waste waters, was also investigated. It was found that polymeric Cr(III) could exist in environmental samples containing μg/L level of Cr, at a level up to 60% of total Cr, suggesting that polymeric Cr(III) could significantly exist in natural environments. Failure in quantifying polymeric Cr(III) would lead to the underestimation of total Cr and bias in Cr speciation. The environmental implication of the presence of polymeric Cr(III) species in the environment deserves further study.
| S-EPMC5027193 | biostudies-literature
Project description:In order to effectively destroy the structure of the passive oxidation film that covers zero-valent iron (ZVI), an Fe(iii)-reducing strain, namely Morganella sp., was isolated from anaerobic activated sludge and coated on ZVI, which was distributed in porous ceramsite made of iron dust, kaolin and straw, with a ratio of 7 : 3 : 1. Batch experiments showed that under the optimized conditions, the maximum removal amount of Cr(vi) by ZVI increased from 7.33 mg g-1 to 26.87 mg g-1 in the presence of the Fe(iii)-reducing bacterium. The column experiment was performed with the addition of the agar globules to supply nutrients to the strain. Compared with ZVI, the column penetration time and maximum capture amount of RB-ZVI increased to 17 h and 112.5 mg g-1, respectively, on the 15th day. Furthermore, the service life of RB-ZVI was prolonged in the existence of the strain. Based on X-ray diffraction, Raman spectroscopy and X-ray photoelectron spectroscopy analyses, the key mechanisms for the removal of Cr(vi) by ZVI coated with Fe(iii)-reducing bacterium were determined to be adsorption, reduction, coprecipitation and biomineralization.
| S-EPMC9075124 | biostudies-literature
Project description:A thiol-functionalized magnetite/graphene oxide (MGO) hybrid as an adsorbent of Hg2+ was successfully synthesized by a two-step reaction. It exhibited a higher adsorption capacity compared to the bare graphene oxide and MGO due to the combined adsorption of thiol groups and magnetite nanocrystals. Its capacity reached 289.9 mg g-1 in a solution with an initial Hg2+ concentration of 100 mg l-1. After being exchanged with H+, the adsorbent could be reused. The adsorption of Hg2+ by the thiol-functionalized MGO fits well with the Freundlich isotherm model and followed pseudo-second-order kinetics.
| S-EPMC3842736 | biostudies-literature
Project description:A magnetic hybrid nanomaterial, which contains magnetite (Fe3O4) particles and diazonium functionalized-reduced graphene oxide (DF-RGO), was fabricated via a three-pot reaction. First, the reduced graphene oxide (RGO) was synthesized via a redox reaction. Second, diazonium functionalized-RGO was prepared via a feasible chemical reaction. Third, Fe3O4 particles were loaded onto the surface of DF-RGO by covalent bonding, fabricating the M-DF-RGO hybrid. The fabricated hybrid was characterized by SEM, TEM, AFM, XRD, XPS, FT-IR, TGA, Raman spectroscopy, and magnetometry. The resulting M-DF-RGO hybrid possessed unique magnetic properties and was applied to remove 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) from aqueous solution. The adsorption of 4-CP and 2,4-DCP on the M-DF-RGO hybrid was performed under various conditions, with respect to initial chlorophenol concentration, pH, and contact time. The results suggest that the adsorption of 4-CP and 2,4-DCP onto the M-DF-RGO hybrid is strongly dependent on pH and weakly dependent on contact time. In addition, the adsorption isotherm of 4-CP and 2,4-DCP on the M-DF-RGO hybrid fits the Freundlich model well and the adsorption capacities of 4-CP and 2,4-DCP on M-DF-RGO reached 55.09 and 127.33 mg g-1, respectively, at pH 6 and 25 °C. In this situation, intermolecular interactions including π-π interactions and hydrogen bonding are operative. The calculated results of density functional theory further demonstrate that 2,4-DCP molecules could be more easily absorbed than 4-CP molecules by the M-DF-RGO hybrid. Moreover, the M-DF-RGO hybrid could be easily separated by a magnetic separation process, and showed good recyclability of more than five cycles.
| S-EPMC9078394 | biostudies-literature
Project description:In the current era of human life, we have been facing an increased consumption of Non-Steroidal Anti-Inflammatory Drugs (NSAIDs). Nevertheless, NSAIDs are not completely metabolized by humans and are further excreted into domestical effluents. Several studies have been showing that a wide variety of pharmaceuticals are present in water effluents and are thus a matter of serious concern in the public health. Although treatment plants use sophisticated technologies for pollutants/contaminants removal, none of these processes was particularly designed for NSAIDs. In this perspective, this work addresses the use of a liquid-liquid extraction approach, employing ionic liquids (ILs), for the removal of NSAIDs from aqueous media. In particular, aqueous biphasic systems (ABS) composed of ILs and aluminium-based salts, which are already used in water treatment plants, were tested for the removal of diclofenac, ibuprofen, naproxen and ketoprofen. With these systems, extraction efficiencies of NSAIDs up to 100% were obtained in a single-step. The recovery of NSAIDs from the IL medium and the recyclability of the IL-rich phase were then ascertained to guarantee the development of a more sustainable and cost-effective strategy. Based on the remarkable increase in the solubility of NSAIDs in the IL-rich phase (from a 300- to a 4100-fold when compared with pure water), water was then studied as an effective anti-solvent, and where single-step recovery percentages of NSAIDs from the IL-rich phase up to 91% were obtained. After the "cleaning" of the IL-rich phase by the induced precipitation of NSAIDs, the phase-forming components were recovered and reused in four consecutive cycles, with no detected losses on both the extraction efficiency and recovery of NSAIDs by induced precipitation. Finally, an integrated process is here proposed, which comprises the (i) removal of NSAIDs from aqueous media, (ii) the cleaning of the IL-rich phase by the recovery of NSAIDs by induced precipitation, and (iii) the phase-forming components recycling and reuse, aiming at unlocking new doors for alternative treatment strategies of aqueous environments.
| S-EPMC6159872 | biostudies-literature
Project description:The present study presents the effective use of nanocrystalline akaganeite for the adsorption of an anionic (SDS), a cationic (CTAB), and a nonionic (tween80) surfactant from wastewater. Equilibrium experiments, as well as thermodynamic analysis, were performed. The maximum SDS adsorption occurs at the lowest pH value (5), the opposite is observed for CTAB (pH = 11), while for tween80, the change of pH value did not affect the adsorption. The equilibrium data could be described by Freundlich and Langmuir isotherms. The maximum adsorption capacity at 25 °C (pH = 8) was 823.96 mg/g for SDS, 1007.93 mg/g for CTAB, and 699.03 mg/g for tween80. The thermodynamic parameters revealed the exothermic and spontaneity nature of the process. Also, FTIR measurements established that surfactants are adsorbed on the surface of akaganeite, replacing adsorbed water.
| S-EPMC5452109 | biostudies-other