Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Influence of Curing Mode on the Surface Energy and Sorption/Solubility of Dental Self-Adhesive Resin Cements.

ABSTRACT: This study investigated the influence of curing mode (dual- or self-cure) on the surface energy and sorption/solubility of four self-adhesive resin cements (SARCs) and one conventional resin cement. The degree of conversion (DC) and surface energy parameters including degree of hydrophilicity (DH) were determined using Fourier transform infrared spectroscopy and contact angle measurements, respectively (n = 5). Sorption and solubility were assessed by mass gain or loss after storage in distilled water or lactic acid for 60 days (n = 5). A linear regression model was used to correlate between the results (%DC vs. DH and %DC/DH vs. sorption/solubility). For all materials, the dual-curing consistently produced significantly higher %DC values than the self-curing (p < 0.05). Significant negative linear regressions were established between the %DC and DH in both curing modes (p < 0.05). Overall, the SARCs showed higher sorption/solubility values, in particular when immersed in lactic acid, than the conventional resin cement. Linear regression revealed that %DC and DH were negatively and positively correlated with the sorption/solubility values, respectively. Dual-curing of SARCs seems to lower the sorption and/or solubility in comparison with self-curing by increased %DC and occasionally decreased hydrophilicity.

SUBMITTER: Kim HJ

PROVIDER: S-EPMC5459112 | biostudies-other | 2017 Feb

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Sorption, solubility and cytotoxicity of novel antibacterial nanofilled dental adhesive resins.

Project description:Dental adhesives hydrolyze in the mouth. This study investigated the water sorption (SOR), solubility (SOL) and cytotoxicity (CYTO) of experimental adhesives containing nitrogen-doped titanium dioxide nanoparticles (N_TiO2). Specimens (n?=?15/group [SOR, SOL]; n?=?10/group [CYTO]) of unaltered Clearfil SE Protect (CSP), OptiBond Solo Plus (OSP), Adper Scotchbond (ASB) and experimental adhesives (OSP?+?25% or 30% of N_TiO2) were fabricated, desiccated (37 °C) and tested for SOR and SOL according to ISO Specification 4049 (2009). CYTO specimens were UV-sterilized (8 J/cm2) and monomer extracted in growth medium (1, 3 or 7 days). Human pulp cells were isolated and seeded (0.5?×?104) for MTT assay. SOR and SOL data was analyzed using GLM and SNK (??=?0.05) and CYTO data was analyzed with Kruskal-Wallis and SNK tests (??=?0.05). SOR and SOL values ranged from 25.80 ?g/mm3 (30% N_TiO2) to 28.01 ?g/mm3 (OSP) and 23.88 ?g/mm3 (30% N_TiO2) to 25.39 ?g/mm3 (25% N_TiO2). CYTO results indicated that pulp cells exposed to experimental materials displayed comparable viabilities (p?>?0.05) to those of OSP. Experimental materials displayed comparable SOR, SOL and CYTO values (p?>?0.05) when compared to unaltered materials. N_TiO2 incorporation have not adversely impacted SOR, SOL and CYTO properties of unaltered adhesives.

| S-EPMC7421579 | biostudies-literature

In vitro cytotoxicity of different dental resin-cements on human cell lines.

Project description:Adhesive resin-cements are increasingly used in modern dentistry. Nevertheless, released substances from resin materials have been shown to cause cellular toxic effects. Disc-shaped specimens from 12 different resin cements and one conventional zinc phosphate cement were prepared and used for direct stimulation of five different human cell lines via transwell cell culture system or in an indirect way using conditioned cell culture media. Cytotoxicity was determined using LDH and BCA assays. All tested cements led to a decrease of cell viability but to a distinct extent depending on cell type, luting material, and cytotoxicity assay. In general, cements exhibited a more pronounced cytotoxicity in direct stimulation experiments compared to stimulations using conditioned media. Interestingly, the conventional zinc phosphate cement showed the lowest impact on cell viability. On cellular level, highest cytotoxic effects were detected in osteoblastic cell lines. All resin cements reduced cell viability of human cells with significant differences depending on cell type and cement material. Especially, osteoblastic cells demonstrated a tremendous increase of cytotoxicity after cement exposure. Although the results of this in vitro study cannot be transferred directly to a clinical setting, it shows that eluted substances from resin cements may disturb osteoblastic homeostasis that in turn could lead to conditions favoring peri-implant bone destruction. Thus, the wide use of resin cements in every clinical situation should be scrutinized. A correct use with complete removal of all cement residues and a sufficient polymerization should be given the utmost attention in clinical usage.

| S-EPMC7817560 | biostudies-literature

Synthesis and characterization of new hydrolytic-resistant dental resin adhesive monomer HMTAF.

Project description:Hydrolytic and enzymatic degradation of resin adhesives over time has been mainly attributed to secondary caries formation of methacrylate-based tooth-colored resin-based composite restorations. Ability of resin adhesive monomers to infiltrate into demineralized dentin forming stiff polymer matrix and potentially bonding to tooth structure is also a crucial property. The only commercially available antibacterial monomer, 12-methacryloyloxydodecyl pyridinium bromide (MDPB), is a quaternary ammonium methacrylate. This methacrylate monomer undergoes hydrolytic degradation, and could not bond to tooth structure. In this study, a new hydrolytic resistant monomer HMTAF was synthesized. It is methacrylamide-based monomer that, unlike methacrylate, is highly resistant to hydrolysis. Its molecular structure has particular functional groups; quaternary ammonium fluoride salt with potential antibacterial fluoride-releasing activity, hydroxyl and amide group with hydrogen bonding potential to dentin collagen. Hydroxyl group also increases monomer hydrophilicity for better penetration into water-saturated dentin and sufficient resin-dentin bond. The synthesized HMTAF and its polymer showed no hydrolytic degradation in acidic environment, while MDPB and its polymer were partially decomposed under this challenge. The conversion of monomer HMTAF to polymer was illustrated by FT-IR. The results indicated that HMTAF is highly resistant to hydrolysis, polymerizable and non-cytotoxic to Vero cell lines. It is a potential monomer to be incorporated into resin adhesives for improving hydrolytic and enzymatic resistance.

| S-EPMC6522974 | biostudies-literature

Bioinspired Ultra-Low Adhesive Energy Interface for Continuous 3D Printing: Reducing Curing Induced Adhesion.

Project description:Additive manufacturing based on liquid resin curing is one of the most promising methods to construct delicate structures. However, precision and speed are limited by the vertical adhesion of in situ cured resin at the curing interface. To overcome the unavoidable adhesion and to develop a general curing interface, we propose a slippery surface taking inspiration of the peristome surface of the pitcher plant. Such surface shows ultra-low adhesive energy at the curing interface due to the inhibition of the direct contact between the cured resin and the solid surface, which also increases the refilling speed of liquid resin. This ultra-low adhesive energy interface is effective for continuous 3D printing and provides insights into the physical mechanisms in reducing vertical solid-solid interfacial adhesion.

| S-EPMC6750170 | biostudies-literature

Self-curing triphenol A-based phthalonitrile resin precursor acts as a flexibilizer and curing agent for phthalonitrile resin.

Project description:Major problems currently limiting the widespread application of phthalonitrile resins are the high precursor melting point and volatility of the curing agent. Herein, a novel self-curing triphenol A-based phthalonitrile resin precursor (TPPA-Ph) was successfully synthesized by reacting α,α,α'-tris(4-hydroxyphenyl)-1-ethyl-4-isopropylbenzene (TPPA) with 4-nitrophthalonitrile (NPh) via nucleophilic substitution. The presence of residual phenolic hydroxyl groups in the TPPA-Ph precursor promoted the curing reaction of phthalonitrile resin in the absence of an additional curing reagent. Self-cured TPPA-Ph resins exhibited relatively low melting points (less than 100 °C), high thermal stability, and a wide processing window (116 °C). Furthermore, the TPPA-Ph precursors contained phenolic hydroxyl and cyano groups that can be used as flexibilizers and curing agents to optimize other phthalonitrile resins. Resorcinol-based phthalonitrile resin (DPPH) cured with various amounts of TPPA-Ph possessed excellent thermal and thermo-oxidative stability with a 5% weight loss temperature exceeding 530 °C, T gs above 380 °C, and a wide processing window and time. Therefore, as a novel precursor and curing agent for phthalonitrile resins, the triphenol A-based phthalonitrile resin is an ideal resin matrix for high-performance composites with broad application prospects in aerospace, shipping, machinery, and other high-tech fields.

| S-EPMC9086328 | biostudies-literature

Adhesive curing through low-voltage activation.

Project description:Instant curing adhesives typically fall within three categories, being activated by either light (photocuring), heat (thermocuring) or chemical means. These curing strategies limit applications to specific substrates and can only be activated under certain conditions. Here we present the development of an instant curing adhesive through low-voltage activation. The electrocuring adhesive is synthesized by grafting carbene precursors on polyamidoamine dendrimers and dissolving in aqueous solvents to form viscous gels. The electrocuring adhesives are activated at -2?V versus Ag/AgCl, allowing tunable crosslinking within the dendrimer matrix and on both electrode surfaces. As the applied voltage discontinued, crosslinking immediately terminated. Thus, crosslinking initiation and propagation are observed to be voltage and time dependent, enabling tuning of both material properties and adhesive strength. The electrocuring adhesive has immediate implications in manufacturing and development of implantable bioadhesives.

| S-EPMC4557340 | biostudies-literature

Evaluating the shear bond strength and remineralization effect of calcium silicate-based and conventional self-adhesive resin cements to caries-affected dentin.

Project description:ObjectiveGiven the importance of preserving caries-affected dentin (CAD) in conservative dentistry, the shear bond strength (SBS) of different resin cements to CAD has been investigated. Here, we aimed to compare the SBS and remineralizing effect of a calcium silicate (TheraCem) and conventional self-adhesive cement (Panavia SA) on the SBS of CAD.Materials and methodsForty-eight extracted third molars (24 sound and 24 CAD) were used. In each group, 12 teeth were prepared for bonding to TheraCem or Panavia SA. After removal of the enamel and caries, resin composite cylinders were luted on the prepared dentin. After 28 days of storage in the artificial saliva, SBS was measured and the failure mode analysis was investigated. The images of fractured sections were analyzed using scanning electron microscopy and energy-dispersive X-ray to evaluate the Ca/P weight ratio.ResultsSBS of CAD and sound dentin was not different when cemented with TheraCem (9.56 ± 4.51 vs. 9.17 ± 2.76, p = .806), but the CAD showed significantly lower SBS to Panavia SA (9.4 ± 2.36 vs. 7.39 ± 2.18, p = .015). The Ca/P ratio in CAD was significantly higher when bonded to both TheraCem and Panavia-SA than that of the controls (p = .001); however, this ratio was not different for those bonded to TheraCem compared to Panavia SA.ConclusionsBased on our results, TheraCem as a calcium silicate cement shows better SBS to attach the restoration to CAD as compared to Panavia SA. Obliteration and mineralization of the dentinal tubules in TheraCem were also higher than in Panavia SA. However, their ability to improve the amount of the Ca/P ratio in CAD was similar.

| S-EPMC9760150 | biostudies-literature

Effect of Curing Mode on Shear Bond Strength of Self-Adhesive Cement to Composite Blocks.

Project description:To overcome the disadvantages of computer-aided design/computer-aided manufacturing (CAD/CAM) processed indirect restorations using glass-ceramics and other ceramics, resin nano ceramic, which has high strength and wear resistance with improved polish retention and optical properties, was introduced. The purpose of this study was to evaluate the shear bond strength and fracture pattern of indirect CAD/CAM composite blocks cemented with two self-etch adhesive cements with different curing modes. Sand-blasted CAD/CAM composite blocks were cemented using conventional resin cement, Rely X Ultimate Clicker (RXC, 3M ESPE, St. Paul, MN, USA) with Single Bond Universal (SB, 3M ESPE, St. Paul, MN, USA) for the control group or two self-adhesive resin cements: Rely X U200 (RXU, 3M ESPE, St. Paul, MN, USA) and G-CEM Cerasmart (GC, GC corporation, Tokyo, Japan). RXU and GC groups included different curing modes (light-curing (L) and auto-curing (A)). Shear bond strength (SBS) analyses were performed on all the specimens. The RXC group revealed the highest SBS and the GC A group revealed the lowest SBS. According to Tukey's post hoc test, the RXC group showed a significant difference compared to the GC A group (p < 0.05). For the curing mode, RXU A and RXU L did not show any significant difference between groups and GC A and GC L did not show any significant difference either. Most of the groups except RXC and RXU L revealed adhesive failure patterns predominantly. The RXC group showed a predominant cohesive failure pattern in their CAD/CAM composite, LavaTM Ultimate (LU, 3M ESPE, St. Paul, MN, USA). Within the limitations of this study, no significant difference was found regarding curing modes but more mixed fracture patterns were showed when using the light-curing mode than when using the self-curing mode.

| S-EPMC5456680 | biostudies-other

Calcium silicate cements endowing bioactivity and sustaining mechanical strength of low-heat-releasing and fast-curing magnesium phosphate cements.

Project description:It is known that magnesium phosphate cements (MPCs) show appreciable mechanical strength and biocompatibility, but the hydration reaction processes often lead to intense heat release while the hydration products present weak resistance to mechanical decay and low bioactivity. Herein we developed an MPC-based system, which was low-heat-releasing and fast-curing in this study, by compounding with self-curing calcium silicate cements (CSCs). The MPC composed of magnesium oxide (MgO), potassium dihydrogen phosphate (KH2PO4), disodium hydrogen phosphate (Na2HPO4), magnesium hydrogen phosphate trihydrate (MgHPO4·3H2O) and chitosan were weakly basic, which would be more stable in vivo. The physicochemical properties indicated that the addition of CSCs could increase the final setting time while decrease the heat release. Meanwhile, the CSCs could endow MPC substrate with apatite re-mineralization reactivity, especially, which add 25 wt.% CSCs showed the most significant apatite deposition. What's more, the mechanical evolution in buffer demonstrated CSCs could enhance and sustain the mechanical strength during degradation, and the internal constructs of cement implants could still be reconstructed by μCT analysis in rabbit femoral bone defect model in vivo. Particularly, appropriate CSCs adjusted the biodegradation and promoted new bone tissue regeneration in vivo. Totally, the MPC/CSCs composite system endows bioactivity and sustains mechanical strength of the MPC, which may be promising for expending the clinical applications of MPC-based bone cements.

| S-EPMC11368412 | biostudies-literature

Color stability of ceramic veneers as a function of resin cement curing mode and shade: 3-year follow-up.

Project description:The influence of curing mode and shade of resin cements on the color stability of minimum-thickness ceramic veneers after a three-year storage time in distilled water was evaluated in this study. Ninety-six 0.5-mm-thick feldspathic ceramic veneers (Mark II) were luted onto resin composite substrates (Filtek Z350 XT, shade A2E) with two light-cured (NX3 Light-cure and AllCem Veneer) and dual-cured resin cements (NX3 dual-cure and AllCem) in various shades. The specimens were stored in distilled water at 37°C. Color measurements were performed with a spectrophotometer at the following times: 1h and 24h; 7, 30, and 180 days; and 1, 2, and 3 years. Data for color difference (ΔEab) light-cured and dual-cured resin cements were analyzed by two-way ANOVA with repeated measures and Tukey's test (α = 0.05). For the light-cured cements, the ΔEab values were as follows: NX3-Yellow (2.37±1.35) = ACV-A1 (2.40±1.21) = ACV-Trans (2.52±1.46) = ACV-E-Bleach M (2.56±1.42) = NX3-White (2.69±1.49) = NX3-Clear (2.98±1.68). The lowest ΔE values were found for 1 h (0.61±0.36)a, followed by 24 h (1.15±0.55)b and 30 days (2.48±1.11)c. One year, 180 days, and 2 and 3 years presented higher ΔEab values (3.34±0.94, 3.52±1.04, 3.52±0.95 and 3.55±1.14, respectively)d. For the dual-cured cements, the ΔEab values varied as follows: NX3-Clear (2.32±1.24)a = NX3-Yellow (2.37±1.32)a = NX3-White (2.76±1.43)a < AC-Trans (3.77±1.91)b = AC-A3 (4.13±2.11)b < AC-A1 (5.38±2.92)c. Considering time, the lowest ΔEab values were found for 1 h (0.48±0.25)a, followed by 24 h (2.13 ±0.83)b, 30 days (3.54±1.31)c, and 180 days (3,70±1.73)c. The follow-up times of 1 (4.43±2.15)d, 2 (5.02±1.74)e, and 3 years (4.90±2.12)e presented higher ΔEab values. This study demonstrated that light-cured resin cements were less susceptible to color change than dual-cured cements. After 2 years of follow-up, all cements presented ΔEab values above the acceptability threshold.

| S-EPMC6602287 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data