Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Study of the Corrosion Resistance of Austenitic Stainless Steels during Conversion of Waste to Biofuel.

ABSTRACT: The paper deals with the corrosion behavior of stainless steels as candidate materials for biofuel production plants by liquefaction process of the sorted organic fraction of municipal solid waste. Corrosion tests were carried out on AISI 316L and AISI 304L stainless steels at 250 °C in a batch reactor during conversion of raw material to bio-oil (biofuel precursor), by exposing specimens either to water/oil phase or humid gas phase. General corrosion rate was measured by weight loss tests. The susceptibility to stress corrosion cracking was evaluated by means of U-bend specimens and slow stress rate tests at 10-6 or 10-5 s-1 strain rate. After tests, scanning electron microscope analysis was carried out to detect cracks and localized attacks. The results are discussed in relation with exposure conditions. They show very low corrosion rates strictly dependent upon time and temperature. No stress corrosion cracking was observed on U-bend specimens, under constant loading. Small cracks confined in the necking cone of specimens prove that stress corrosion cracking only occurred during slow strain rate tests at stresses exceeding the yield strength.

SUBMITTER: Cabrini M

PROVIDER: S-EPMC5503400 | biostudies-other | 2017 Mar

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Electrochemical Polishing of Austenitic Stainless Steels.

Project description:Improvement of the corrosion resistance capability, surface roughness, shining of stainless-steel surface elements after electrochemical polishing (EP) is one of the most important process characteristics. In this paper, the mechanism, obtained parameters, and results were studied on electropolishing of stainless-steel samples based on the review of the literature. The effects of the EP process parameters, especially current density, temperature, time, and the baths used were presented and compared among different studies. The samples made of stainless steel presented in the articles were analysed in terms of, among other things, surface roughness, resistance to corrosion, microhardness, and chemical composition. All results showed that the EP process greatly improved the analysed properties of the stainless-steel surface elements.

| S-EPMC7321480 | biostudies-literature

Atomic-scale decoration for improving the pitting corrosion resistance of austenitic stainless steels.

Project description:Stainless steels are susceptible to the localized pitting corrosion that leads to a huge loss to our society. Studies in the past decades confirmed that the pitting events generally originate from the local dissolution in MnS inclusions which are more or less ubiquitous in stainless steels. Although a recent study indicated that endogenous MnCr2O4 nano-octahedra within the MnS medium give rise to local nano-galvanic cells which are responsible for the preferential dissolution of MnS, effective solutions of restraining the cells from viewpoint of electrochemistry are being tantalizingly searched. Here we report such a galvanic corrosion can be greatly resisted via bathing the steels in Cu(2+)-containing solutions. This chemical bath generates Cu(2-δ)S layers on the surfaces of MnS inclusions, invalidating the nano-galvanic cells. Our study provides a low-cost approach via an atomic scale decoration to improve the pitting corrosion resistance of stainless steels in a volume-treated manner.

| S-EPMC3884226 | biostudies-other

Hierarchical Multiple Precursors Induced Heterogeneous Structures in Super Austenitic Stainless Steels by Cryogenic Rolling and Annealing

Project description: Not available

| S-EPMC10532896 | biostudies-literature

Quantitative 3D Characterization for Kinetics of Corrosion Initiation and Propagation in Additively Manufactured Austenitic Stainless Steel.

Project description:In situ X-ray computed tomography (X-ray CT) is used to investigate the effects of characteristic microstructural features on the pitting initiation and propagation in austenitic stainless steel specimens prepared with laser powder bed fusion (LPBF) additive manufacturing. In situ X-ray CT in probing the mechanism and kinetics of localized corrosion is demonstrated by immersing two LPBF specimens with different porosities in an aggressive ferric chloride solution for the evaluation of corrosion. X-ray CT images are acquired from the specimens after every 8 hours of immersion over an extended period of time (216 hours). Corrosion pit growth is then quantitatively analyzed with a data-constrained modeling method. The pitting growth mechanism of LPBF stainless steel is found to be different from that of conventional stainless steels. More specifically, the mechanism of corrosion pit initiation is closely correlated with the original lack of fusion porosity (LOF) distribution on the surface of the specimens and preferential pit propagation through the LOF pores inside the specimens. Pit growth kinetics are derived from pit volume changes determined through 3D data analysis. The pit growth kinetics in LPBF specimens are found to vary in the initial pit formation, competitive pit propagation, and the dominant pit growth stages.

| S-EPMC9799015 | biostudies-literature

A study of bacteria adhesion and microbial corrosion on different stainless steels in environment containing <i>Desulfovibrio vulgaris</i>.

Project description:Stainless steel is an important material used in many applications due to its mechanical strength and corrosion-resistant properties. The high corrosion resistance of stainless steel is provided by the passive film. Different stainless steels have different alloy elements and surface properties which could have a significant influence on bacterial attachment to the surface and thus might result in different microbial corrosion behaviours. In this study, the effect of adhesion of sulfate-reducing bacteria (SRB) on corrosion behaviour in artificial seawater on different stainless steels was investigated. Stainless steel materials used were SS 410, SS 420, SS 316 and DSS 2205 and pure chromium. The contact angle was measured to study the effect of surface properties of materials. Adhesion was measured by counting cells attached to the surface of materials. The corrosion behaviour of the materials was measured by electrochemical testing including measuring open circuit potential, electrochemical impedance spectroscopy and potentiodynamic behaviour. The long-term corrosion behaviour of each material was studied after six months of exposure by measuring weight loss and surface analysis with scanning electron microscope with energy-dispersive X-ray analysis. Hydrophobicity had a strong effect on bacterial attachment. Alloying elements e.g. nickel also had shown its ability to attract bacteria to adhere on the surface. However, the corrosion rate of different materials is determined not only by bacterial attachment but also by the stability of the passive film which is determined by the alloying elements, such as Mo and Cr. Chromium showed high resistance to corrosion, possibly due to toxicity on bacterial attachment. The nature of bacterial attachment and corrosion behaviour of the materials are discussed.

| S-EPMC7890485 | biostudies-literature

Hydrogen-Induced Delayed Cracking in TRIP-Aided Lean-Alloyed Ferritic-Austenitic Stainless Steels.

Project description:Susceptibility of three lean-alloyed ferritic-austenitic stainless steels to hydrogen-induced delayed cracking was examined, concentrating on internal hydrogen contained in the materials after production operations. The aim was to study the role of strain-induced austenite to martensite transformation in the delayed cracking susceptibility. According to the conducted deep drawing tests and constant load tensile testing, the studied materials seem not to be particularly susceptible to delayed cracking. Delayed cracks were only occasionally initiated in two of the materials at high local stress levels. However, if a delayed crack initiated in a highly stressed location, strain-induced martensite transformation decreased the crack arrest tendency of the austenite phase in a duplex microstructure. According to electron microscopy examination and electron backscattering diffraction analysis, the fracture mode was predominantly cleavage, and cracks propagated along the body-centered cubic (BCC) phases ferrite and α'-martensite. The BCC crystal structure enables fast diffusion of hydrogen to the crack tip area. No delayed cracking was observed in the stainless steel that had high austenite stability. Thus, it can be concluded that the presence of α'-martensite increases the hydrogen-induced cracking susceptibility.

| S-EPMC5553521 | biostudies-other

Stress Corrosion Cracking of an Austenitic Stainless Steel in Nitrite-Containing Chloride Solutions.

Project description:This article describes the susceptibility of 316L stainless steel to stress corrosion cracking (SCC) in a nitrite-containing chloride solution. Slow strain rate testing (SSRT) in 30 wt. % MgCl₂ solution established SCC susceptibility, as evidenced by post-SSRT fractography. Addition of nitrite to the chloride solution, which is reported to have inhibitive influence on corrosion of stainless steels, was found to increase SCC susceptibility. The susceptibility was also found to increase with nitrite concentration. This behaviour is explained on the basis of the passivation and pitting characteristics of 316L steel in chloride solution.

| S-EPMC5456438 | biostudies-other

Dislocation Strengthening without Ductility Trade-off in Metastable Austenitic Steels.

Project description:Strength and ductility are mutually exclusive if they are manifested as consequence of the coupling between strengthening and toughening mechanisms. One notable example is dislocation strengthening in metals, which invariably leads to reduced ductility. However, this trend is averted in metastable austenitic steels. A one-step thermal mechanical treatment (TMT), i.e. hot rolling, can effectively enhance the yielding strength of the metastable austenitic steel from 322?±?18?MPa to 675?±?15?MPa, while retaining both the formability and hardenability. It is noted that no boundaries are introduced in the optimized TMT process and all strengthening effect originates from dislocations with inherited thermal stability. The success of this method relies on the decoupled strengthening and toughening mechanisms in metastable austenitic steels, in which yield strength is controlled by initial dislocation density while ductility is retained by the capability to nucleate new dislocations to carry plastic deformation. Especially, the simplicity in processing enables scaling and industrial applications to meet the challenging requirements of emissions reduction. On the other hand, the complexity in the underlying mechanism of dislocation strengthening in this case may shed light on a different route of material strengthening by stimulating dislocation activities, rather than impeding motion of dislocations.

| S-EPMC5064382 | biostudies-literature

Crystallographic orientation data from chloride-induced stress corrosion crack (CISCC) paths in gas tungsten arc welded (GTAW) austenitic stainless steel 304L.

Project description:This Data in Brief article presents crystallographic data collected along chloride-induced stress corrosion cracks (CISCC) in a gas tungsten arc welded (GTAW) austenitic stainless steel (AuSS) 304L. The experimental setup involved a welded stainless steel 304L coupon of dimensions 105 mm × 18.5 mm × 3 mm, loaded in a 4-point bending fixture with a maximum tensile stress of 380 MPa. The fixtured specimen was immersed in boiling magnesium chloride (MgCl2) solution until a through-crack was observed on the specimen surface after 17 hours of boiling. The cross-section was subsequently polished, and 37 cracks of interest in the heat affected zone (HAZ) and weld zone (WZ) were selected for crystallographic characterization. Scanning electron microscopy (SEM) based electron backscatter diffraction (EBSD) was used to map the grain orientations along and surrounding each crack path. The obtained orientation imaging microscopy (OIM) datasets were post-processed using EDAX OIM V8 proprietary software to generate inverse pole figures (IPF), image quality (IQ) figures, detector signal (SEM) images, and to determine the Taylor factor and Schmid factor of mapped grains. This dataset can be used to understand CISCC crack initiation, propagation, and termination behaviors, as has been reported in the accompanying original research article. This data article providing the raw EBSD OIM datasets and processed images formatted for accessibility in future studies. This comprehensive EBSD dataset can further be used to extract grain boundary misorientation information; benchmark comparative studies of SCC/CISCC in AuSS and other Fe or Ni alloys; and provide critical validation data on grain morphology, misorientation, and crystallography for GTAW and CISCC models.

| S-EPMC8956886 | biostudies-literature

Effect of Secondary Phase Precipitation on the Corrosion Behavior of Duplex Stainless Steels.

Project description:Duplex stainless steels (DSSs) with austenitic and ferritic phases have been increasingly used for many industrial applications due to their good mechanical properties and corrosion resistance in acidic, caustic and marine environments. However, DSSs are susceptible to intergranular, pitting and stress corrosion in corrosive environments due to the formation of secondary phases. Such phases are induced in DSSs during the fabrication, improper heat treatment, welding process and prolonged exposure to high temperatures during their service lives. These include the precipitation of sigma and chi phases at 700-900 °C and spinodal decomposition of ferritic grains into Cr-rich and Cr-poor phases at 350-550 °C, respectively. This article gives the state-of the-art review on the microstructural evolution of secondary phase formation and their effects on the corrosion behavior of DSSs.

| S-EPMC5455814 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data