Behaviour of Corroded Single Stud Shear Connectors.
Ontology highlight
ABSTRACT:
SUBMITTER: Xue W
PROVIDER: S-EPMC5503412 | biostudies-other | 2017 Mar
REPOSITORIES: biostudies-other
Similar Datasets
Project description:According to recent researches, angle shear connectors are appropriate to transfer longitudinal shear forces across the steel-concrete interface. Angle steel profile has been used in different positions as L-shaped or C-shaped shear connectors. The application of angle shear connectors in tilted positions is of interest in this study. This study investigates the behaviour of tilted-shaped angle shear connectors under monotonic loading using experimental push out tests. Eight push-out specimens are tested to investigate the effects of different angle parameters on the ultimate load capacity of connectors. Two different tilted angles of 112.5 and 135 degrees between the angle leg and steel beam are considered. In addition, angle sizes and lengths are varied. Two different failure modes were observed consisting of concrete crushing-splitting and connector fracture. By increasing the size of connector, the maximum load increased for most cases. In general, the 135 degrees tilted angle shear connectors have a higher strength and stiffness than the 112.5 degrees type.
| S-EPMC4671601 | biostudies-literature
Project description:This paper investigates the behaviour of C-shaped and L-shaped angle shear connectors embedded in solid concrete slabs. An effective finite element model is proposed to simulate the push out tests of these shear connectors that encompass nonlinear material behaviour, large displacement and damage plasticity. The finite element models are validated against test results. Parametric studies using this nonlinear model are performed to investigate the variations in concrete strength and connector dimensions. The finite element analyses also confirm the test results that increasing the length of shear connector increases their shear strength proportionately. It is observed that the maximum stress in L-shaped angle connectors takes place in the weld attachment to the beam, whereas in the C-shaped angle connectors, it is in the attached leg. The location of maximum concrete compressive damage is rendered in each case. Finally, a new equation for prediction of the shear capacity of C-shaped angle connectors is proposed.
| S-EPMC4968825 | biostudies-literature
Project description:Cells that form the corneal epithelium, the outermost layer of the cornea, are exposed to shear stress through blinking during waking hours. In this in vitro study, the effect of fluid shear stress on human corneal epithelial cells (HCECs) was investigated. Following exposure to shear stresses of 4 and 8 dyn/cm2, HCECs showed cytoskeletal rearrangement with more prominent, organized and elongated filamentous actin. Cytoskeletal changes were time-dependent, and were most significant after 24 hours of shear stress. Higher rates of migration and proliferation, as evaluated by a scratch assay, were also observed following 24 hours of low shear stress exposure (4 dyn/cm2). This result contrasted the poor migration observed in samples scratched before shear exposure, indicating that shear-induced cytoskeletal changes played a key role in improved wound healing and must therefore precede any damage to the cell layer. HCEC cytoskeletal changes were accompanied by an upregulation in integrin ?1 and downregulation of ICAM-1. These results demonstrate that HCECs respond favourably to flow-induced shear stress, impacting their proliferation and migration properties as well as phenotype.
| S-EPMC5491001 | biostudies-literature
Project description:This study defines network types of wheat gluten to describe spatial arrangements of gluten networks in relation to dough mechanical behaviour. To achieve a high variety in gluten arrangements, ten specific and unspecific gluten-modifying agents in increasing concentrations were added to wheat dough. Gluten microstructure was visualized by confocal laser scanning microscopy and quantified by protein network analysis. Dough rheological behaviour was determined by both oscillatory and creep-recovery tests. Based on correlation matrices and principal component analysis, six different network types were identified and associated to their rheological characteristics: a cleaved (low viscous), rigid (highly viscous), spread (viscoelastic), strengthened (viscoelastic), particulate and dense (highly viscous) or particulate and loose (low viscous) network. Furthermore, rheological dough properties of specifically gluten-modified samples were predicted with five microstructural gluten attributes (lacunarity, branching rate, end-point rate, protein width, average protein length) and assigned properly by the obtained partial least square model with an accuracy up to 90% (e.g., R2Y = 0.84 for G*, 0.85 for tanδ, 0.90 for Jmax). As a result, rheological properties of wheat doughs were predicted from microstructural investigations. This novel, quantitative definition of the relation between structure and mechanical behaviour can be used for developments of new wheat products with targeted properties.
| S-EPMC6423116 | biostudies-literature
Project description:The major connector is the most vital component critically subjected to maximal stress concentration due to various forces acting on it. The main requirement of a major connector is its resistance to deformation by occlusal stresses. This resistance to deformation is a direct consequence of the rigidity of the major connector. Thus rigidity of the major connector is paramount to resist flexing and torquing forces that could be transmitted to the abutment teeth and other structures as destructive forces. The commonly used major connectors for the mandibular arch are lingual bar and lingual plate. In the present study, the deflection of various major connector designs due to occlusal load is assessed by finite element method. They have been analyzed through finite element models. The differences in the deflection behaviour of mandibular major connector used in Kennedy's Class I, Class II, Class III, and Class IV edentulous situations have been compared. A CT scan of human edentulous mandible was taken and each section from symphysis to condylar region was projected on a graph paper and three-dimensional volumes were created from connected successive profiles to define the final solid geometry of cortical bone. Six framework models with different mandibular major connectors, lingual bar and lingual plate for Kennedy's Class I, Class II, Class III, and Class IV situations were created. The three dimensional finite element models corresponding to the geometric model were generated using Ansys's pre-processor. The model was assigned material properties. A vertical biting force of 20 N was applied. The results showed that the maximum deflection was seen in the saddle area when compared to other areas, i.e., major connector and the occlusal rest regions. The lingual bar in Kennedy's Class III situation and lingual plate in Kennedy's Class IV situation showed the least deflection when compared to Class I and Class II (distal extensions) situations. Lingual plate is more rigid major connector than lingual bar.
| S-EPMC3792305 | biostudies-literature
Project description:Conventional multiple-track-location shear wave elasticity imaging (MTL-SWEI) is a powerful tool for noninvasively estimating tissue elasticity. The resolution and noise levels of MTL-SWEI systems, however, are limited by ultrasound speckle. Single-track-location SWEI (STL-SWEI) is a novel variant which fixes the position of the tracking beam and modulates the push location to effectively cancel out the effects of speckle-induced bias. We present here a 3-D STL-SWEI system, which provides full suppression of lateral and elevation speckle bias for high-resolution volumetric elasticity imaging, and requires no spatial smoothing to make accurate measurements of shear wave speed. We demonstrate and analyze the system's performance in homogeneous and layered elasticity phantoms.
| S-EPMC5767318 | biostudies-literature
Project description:Viruses build icosahedral capsids of specific size and shape by regulating the spatial arrangement of the hexameric and pentameric protein capsomers in the growing shell during assembly. In the T=7 capsids of Escherichia coli bacteriophage HK97 and other phages, 60 capsomers are hexons, while the rest are pentons that are correctly positioned during assembly. Assembly of the HK97 capsid to the correct size and shape has been shown to depend on specific ionic contacts between capsomers. We now describe additional ionic interactions within capsomers that also regulate assembly. Each is between the long hairpin, the "E-loop," that extends from one subunit to the adjacent subunit within the same capsomer. Glutamate E153 on the E-loop and arginine R210 on the adjacent subunit's backbone alpha-helix form salt bridges in hexamers and pentamers. Mutations that disrupt these salt bridges were lethal for virus production, because the mutant proteins assembled into tubes or sheets instead of capsids. X-ray structures show that the E153-R210 links are flexible and maintained during maturation despite radical changes in capsomer shape. The E153-R210 links appear to form early in assembly to enable capsomers to make programmed changes in their shape during assembly. The links also prevent flattening of capsomers and premature maturation. Mutant phenotypes and modeling support an assembly model in which flexible E153-R210 links mediate capsomer shape changes that control where pentons are placed to create normal-sized capsids. The E-loop may be conserved in other systems in order to play similar roles in regulating assembly.
| S-EPMC5555079 | biostudies-literature
Project description:In this study, we aimed to provide systematic and critical research to investigate the shear performance and reveal the corresponding structural response and fracture characteristics of the monolayer GK membrane. The results demonstrate that the kirigami structure significant alters the shear performance of graphene-based sheets. Tuning the porosity by controlling the incision size, pore distribution, and incision direction can effectively adjust the shear strength and elastic modulus of GK membranes. The trade-off of the stress and strain of the GK membrane is critical to its shear behaviour. The microstructural damage processes and failure characteristics further reveal that making more carbon atoms on the GK structure sharing the strain energy is the key to reinforcing the shear performance of membranes. Based on this, we found that adding the shear loading in the direction of perpendicular to the incisions on the GK membrane can significantly improve the shear strength and stiffness of the membrane by 26.2-32.1% and 50.2-75.3% compared to applying shear force parallel to GK incisions. This research not only broadens the understanding of shear properties of monolayer GO membrane but also provides more reference on the fracture characteristics of GK membranes for future manufacturing and applications.
| S-EPMC9501511 | biostudies-literature
Project description:As part of an international effort to sequence the rice genome, the Clemson University Genomics Institute is developing a sequence-tagged-connector (STC) framework. This framework includes the generation of deep-coverage BAC libraries from O. sativa ssp. japonica c.v. Nipponbare and the sequencing of both ends of the genomic DNA insert of the BAC clones. Here, we report a survey of the transposable elements (TE) in >73,000 STCs. A total of 6848 STCs were found homologous to regions of known TE sequences (E<10(-5)) by FASTX search of STCs against a set of 1358 TE protein sequences obtained from GenBank. Of these TE-containing STCs (TE-STCs), 88% (6027) are related to retroelements and the remaining are transposase homologs. Nearly all DNA transposons known previously in plants were present in the STCs, including maize Ac/Ds, En/Spm, Mutator, and mariner-like elements. In addition, 2746 STCs were found to contain regions homologous to known miniature inverted-repeat transposable elements (MITEs). The distribution of these MITEs in regions near genes was confirmed by EST comparisons to MITE-containing STCs, and our results showed that the association of MITEs with known EST transcripts varies by MITE type. Unlike the biased distribution of retroelements in maize, we found no evidence for the presence of gene islands when we correlated TE-STCs with a physical map of the CUGI BAC library. These analyses of TEs in nearly 50 Mb of rice genomic DNA provide an interesting and informative preview of the rice genome.
| S-EPMC310901 | biostudies-literature
Project description:Luer slip is one of the gold standards for chip-to-world interface in microfluidics. They have outstanding mechanical and operational robustness in a broad range of applications using water and solvent-based liquids. Still, their main drawbacks are related to their size: they have relatively large dead volumes and require a significant footprint to assure a leak-free performance. Such aspects make their integration in systems with high microchannel density challenging. To date, there has been no geometrical optimization of the Luer slips to provide a solution to the mentioned drawbacks. This work aims to provide the rules toward downscaling the Luer slips. To this effect, seven variations of the Luer slip male connectors and five variations of Luer slip female connectors have been designed and manufactured focusing on the reduction of the size of connectors and minimization of the dead volumes. In all cases, female connectors have been developed to pair with the corresponding male connector. Characterization has been performed with a tailor-made test bench in which the closure force between male and female connectors has been varied between 7.9 and 55 N. For each applied closure force, the test bench allows liquid pressures to be tested between 0.5 and 2.0 bar. Finally, the analysis of a useful life determines the number of cycles that the connectors can withstand before leakage.
| S-EPMC9194524 | biostudies-literature