Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Fabrication of TiCx-TiB₂/Al Composites for Application as a Heat Sink.

ABSTRACT: Metal matrix composites reinforced with ceramic particles have become the most attractive material in the research and development of new materials for thermal management applications. In this work, 40-60 vol. % TiCx-TiB₂/Al composites were successfully fabricated by the method of combustion synthesis and hot press consolidation in an Al-Ti-B₄C system. The effect of the TiCx-TiB₂ content on the microstructure and compression properties of the composites was investigated. Moreover, the abrasive wear behavior and thermo-physics properties of the TiCx-TiB₂/Al composite were studied and compared with the TiCx/Al composite. The compression properties, abrasive wear behavior and thermo-physics properties of the TiCx-TiB₂/Al composite are all better than those of the TiCx/Al composite, which confirms that the TiCx-TiB₂/Al composite is more appropriate for application as a heat sink.

SUBMITTER: Shu S

PROVIDER: S-EPMC5509092 | biostudies-other | 2016 Jul

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Evaluation of Residual Stress Distribution and Relaxation on In Situ TiB₂/7050 Al Composites.

Project description:Interior residual stresses induced by quenching may cause distortion during subsequent machining processes. Hence, various strategies have been employed to relieve the interior residual stress, such as stretching, post treatment, and other techniques. In this study, the stress distribution inside TiB₂/7050 Al composite extrusions was investigated and the effects of different methods on relieving the quenching-induced stress were compared. Firstly, three TiB₂/7050 Al composite extrusions were treated by stretching, stretching and heat treatment, and stretching and cold treatment processes, respectively. Then, the multiple-cut contour method was employed to assess the residual stresses in the three workpieces. Experimental results indicate that the interior stress of TiB₂/7050 Al composite extrusions after stretching ranges from −89 MPa to +55 MPa, which is larger than that in 7050 aluminum alloy, which ranges from −25 Pa to +25 MPa. The heat treatment performs better than the cold treatment to reduce the post-stretching residual stress, with a reduction of 23.2⁻46.4% compared to 11.3⁻40.8%, respectively. From the stress map, it is found that the stress distribution after the heat treatment is more uniform compared with that after the cold treatment.

| S-EPMC5978083 | biostudies-literature

Fabrication of Al/Mg/Al Composites via Accumulative Roll Bonding and Their Mechanical Properties.

Project description:Al(1060)/Mg(AZ31)/Al(1060) multilayered composite was successfully produced using an accumulative roll bonding (ARB) process for up to four cycles at an elevated temperature (400 °C). The microstructure evolution of the composites and the bonding characteristics at the interfaces between Al and Mg layers with increasing ARB cycles were characterized through optical microscopy, field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). It was found that the grains of Al and Mg layers were significantly refined and Al₃Mg₂ and Al12 Mg17 intermetallic compound layers formed at the Al/Mg bonding interfaces. The strength increased gradually and the ultimate tensile strength (UTS) reached a maximum value of about 240 MPa at the third pass. Furthermore, the strengthening mechanism of the composite was analyzed based on the fracture morphologies.

| S-EPMC5457262 | biostudies-other

Refining Mechanism of 7075 Al Alloy by In-Situ TiB? Particles.

Project description:The nucleation undercooling of TiB?/7075 Al matrix composites, the microstructure observed after solidification at different cooling rate, and the size and distribution of TiB? particles were investigated. The experimental results have shown that the grain sizes of TiB?/7075 Al matrix composites firstly decreased, then increased, and finally decreased again with the increase of TiB? content. The nucleation undercooling of TiB?/7075 Al matrix composites first increased, then decreased, and finally increased again with the increase of TiB? content when the cooling rates was 5 and 10 °C/min respectively, but kept decreasing with the increase of TiB? content at a cooling rate of 20 °C/min. The melting and solidification process showed no significant change with the decrease of cooling rate in 9.0% TiB?/7075 Al matrix composites. Most small particles can act as heterogeneous nucleus, which induced grain growth and were captured into the grain by the solid/liquid interface. At the same time, most of the larger particles and a minority of the small TiB? particles are pushed into the grain boundary; locating in the grain boundary can hinder the Al atoms from diffusing during the solidification process and restrain ?-Al phase growth. The influence of particles shifted from dominating by locating to dominating by nucleation as the quantity of TiB? particles increased.

| S-EPMC5459188 | biostudies-literature

Microwave-Assisted Fabrication of Mesoporous Silica-Calcium Phosphate Composites for Dental Application.

Project description:Herein, the microwave-assisted wet precipitation method was used to obtain materials consisting of mesoporous silica (SBA-15) and calcium orthophosphates (CaP). Composites were prepared through immersion of mesoporous silica in different calcification coating solutions and then exposed to microwave radiation. The composites were characterized in terms of molecular structure, crystallinity, morphology, chemical composition, and mineralization potential by Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM-EDX). The application of microwave irradiation resulted in the formation of different types of calcium orthophosphates such as calcium deficient hydroxyapatite (CDHA), octacalcium phosphate (OCP), and amorphous calcium phosphate (ACP) on the SBA-15 surface, depending on the type of coating solution. The composites for which the progressive formation of hydroxyapatite during incubation in simulated body fluid was observed were further used in the production of final pharmaceutical forms: membranes, granules, and pellets. All of the obtained pharmaceutical forms preserved mineralization properties.

| S-EPMC7796352 | biostudies-literature

Fabrication and Characterization of In Situ Zn-TiB<sub>2</sub> Nanocomposite.

Project description:Zinc (Zn) matrix composite has been newly discovered categories of biodegradable materials. With a combination of chemical stability, thermal stability and biocompatibility, ceramic nanoparticles outperformed intermetallics of zinc alloys with inherent advantages of retaining a proper corrosion rate and an exceptional ductility. Compared with Zn alloys, Zn matrix nanocomposites showed an unprecedented strengthening without sacrifices of corrosion rate, which were introduced by intermetallics. In this work, in situ titanium diboride (TiB2) reinforced Zn nanocomposite was prepared via a few cost-effective and economical methods: flux-assisted synthesis (FAS), ultrasound-assisted nanoparticle homogenization and hot rolling. 3 vol.% of TiB2 nanoparticles were synthesized with an average size of 454nm, followed by molten salt assisted ultrasound homogenization and hot rolling. Hot-rolled (HR) Zn-TiB2 performed high strength and high ductility, mostly due to precipitation strengthening (Orowan strengthening). Yield stress (YS) and ultimate tensile stress (UTS) increased by 90% and 45%, respectively, while the elongation to failure retained 23%. The mechanical performance of Zn-TiB2 made it promise to serve as an innovative biodegradable material for load-bearing applications.

| S-EPMC8238460 | biostudies-literature

Bulk TiB₂-Based Ceramic Composites with Improved Mechanical Property Using Fe-Ni-Ti-Al as a Sintering Aid.

Project description:The densification behavior, microstructure and mechanical properties of bulk TiB₂-based ceramic composites, fabricated using the spark plasma sintering (SPS) technique with elements of (Fe-Ni-Ti-Al) sinter-aid were investigated. Comparing the change of shrinkage displacement of pure TiB₂ and TiB₂-5 wt% (Fe-Ni-Ti-Al), the addition of elements Fe-Ni-Ti-Al into TiB₂ can facilitate sintering of the TiB₂ ceramics. As the sintering temperature exceeds 1300 °C, the relative density does not significantly change. Alumina particles and austenite (Fe-Ni-Ti) metallic binder distributed homogeneously in the grain boundary of TiB₂ can inhibit the growth of the TiB₂ grains when the sintering temperature is below 1300 °C. The density and particle size of TiB₂ greatly influence the mechanical behavior of TiB₂-5 wt% (Fe-Ni-Ti-Al) composites. The specimen sintered at 1300 has the highest microhardness of 21.1 ± 0.1 GPa with an elastic modulus of 461.4 GPa. The content of secondary borides (M₂B, being M = Fe, Ni), which are more brittle than TiB₂ particles, can also influence the fracture toughness. The specimen sintered at 1500 °C has the highest fracture toughness of 6.16 ± 0.30 MPa·m1/2 with the smallest M₂B phase. The results obtained provide insight into fabrication of ceramic composites with improved mechanical property.

| S-EPMC5456019 | biostudies-other

Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application.

Project description:Aluminium-based hybrid composites are a new class of advanced materials with the potential of satisfying the demands in engineering applications. This paper describes the effects of carbon addition on the formation and properties of AMC with SiC nanoparticles reinforcement. The composites were produced via mechanical alloying followed by hot pressing. Three forms of carbon, graphite (GR), multiwalled carbon nanotubes (CNTs), and, for the first time, glassy carbon (GC), were used for the hybrid composites manufacturing and compared with tribological properties of Al-SiC composite without carbon addition. GC and CNTs enhanced formation of Al-SiC composite particles and resulted in a homogeneous distribution of reinforcing particles. On the other hand, GR addition altered mechanochemical alloying and did not lead to a proper distribution of nanoparticulate SiC reinforcement. Hot pressing technique led to the reaction between Al and carbon as well as SiC particles and caused the formation of Al₄C₃ and γ-Al₂O₃. The subsistence of carbon particles in the composites altered the predominant wear mechanisms since the wear reduction and the stabilization of the friction coefficient were observed. GC with simultaneous γ-Al₂O₃ formation in the hybrid Al-SiC(n)-C composites turned out to be the most effective additive in terms of their tribological behaviour.

| S-EPMC5554060 | biostudies-other

High Thermal Dissipation of Al Heat Sink When Inserting Ceramic Powders by Ultrasonic Mechanical Coating and Armoring.

Project description:Aluminum alloys, which serve as heat sink in light-emitting diode (LED) lighting, are often inherent with a high thermal conductivity, but poor thermal total emissivity. Thus, high emissive coatings on the Al substrate can enhance the thermal dissipation efficiency of radiation. In this study, the ultrasonic mechanical coating and armoring (UMCA) technique was used to insert various ceramic combinations, such as Al₂O₃, SiO₂, or graphite, to enhance thermal dissipation. Analytic models have been established to couple the thermal radiation and convection on the sample surface through heat flow equations. A promising match has been reached between the theoretical predictions and experimental measurements. With the adequate insertion of ceramic powders, the temperature of the Al heat sinks can be lowered by 5-11 °C, which is highly favorable for applications requiring cooling components.

| S-EPMC5458992 | biostudies-other

Microstructure Evolution and Mechanical Properties of Al-TiB₂/TiC In Situ Aluminum-Based Composites during Accumulative Roll Bonding (ARB) Process.

Project description:In this study, a kind of Al-TiB₂/TiC in situ composite was successfully prepared using the melt reaction method and the accumulative roll-bonding (ARB) technique. The microstructure evolution of the composites with different deformation treatments was characterized using field emission scanning electron microscopy (FESEM) and a transmission electron microscope (TEM). The mechanical properties of the Al-TiB₂/TiC in situ composite were also studied with tensile and microhardness tests. It was found that the distribution of reinforcement particles becomes more homogenous with an increasing ARB cycle. Meanwhile, the mechanical properties showed great improvement during the ARB process. The ultimate tensile strength (UTS) and microhardness of the composites were increased to 173.1 MPa and 63.3 Hv after two ARB cycles, respectively. Furthermore, the strengthening mechanism of the composite was analyzed based on its fracture morphologies.

| S-EPMC5459192 | biostudies-other

Flux-tunable heat sink for quantum electric circuits.

Project description:Superconducting microwave circuits show great potential for practical quantum technological applications such as quantum information processing. However, fast and on-demand initialization of the quantum degrees of freedom in these devices remains a challenge. Here, we experimentally implement a tunable heat sink that is potentially suitable for the initialization of superconducting qubits. Our device consists of two coupled resonators. The first resonator has a high quality factor and a fixed frequency whereas the second resonator is designed to have a low quality factor and a tunable resonance frequency. We engineer the low quality factor using an on-chip resistor and the frequency tunability using a superconducting quantum interference device. When the two resonators are in resonance, the photons in the high-quality resonator can be efficiently dissipated. We show that the corresponding loaded quality factor can be tuned from above 105 down to a few thousand at 10 GHz in good quantitative agreement with our theoretical model.

| S-EPMC5910410 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data