Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Removal of Cr(VI) from Water Using a New Reactive Material: Magnesium Oxide Supported Nanoscale Zero-Valent Iron.

ABSTRACT: The chromium pollution of water is an important environmental and health issue. Cr(VI) removal by means of metallic iron is an attractive method. Specifically, nanoscopic zero valent iron (NZVI) shows great reactivity, however, its applicability needs to be further investigated. In the present paper, NZVI was supported on MgO grains to facilitate the treatments for remediation of chromium-contaminated waters. The performances and mechanisms of the developed composite, in the removal of hexavalent chromium, were investigated by means of batch and continuous tests. Kinetic studies, under different operating conditions, showed that reduction of Cr(VI) could be expressed by a pseudo second-order reaction kinetic. The reaction rate increased with the square of Fe(0) amount, while it was inversely proportional to the initial chromium concentration. The process performance was satisfactory also under uncontrolled pH, and a limited influence of temperature was observed. The reactive material was efficiently reusable for many cycles without any regeneration treatment. The performances in continuous tests were close to 97% for about 80 pore volume of reactive material.

SUBMITTER: Siciliano A

PROVIDER: S-EPMC5509277 | biostudies-other | 2016 Aug

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Removal of Chromium(VI) by Nanoscale Zero-Valent Iron Supported on Melamine Carbon Foam.

Project description:The overuse of chromium (Cr) has significantly negatively impacted human life and environmental sustainability. Recently, the employment of nano zero-valent iron (nZVI) for Cr(VI) removal is becoming an emerging approach. In this study, carbonized melamine foam-supported nZVI composites, prepared by a simple impregnation-carbonization-reduction method, were assessed for efficient Cr(VI) removal. The prepared composites were characterized by XPS, SEM, TEM, BET and XRD. Batch experiments at different conditions revealed that the amount of iron added, the temperature of carbonization and the initial Cr(VI) concentration were critical factors. Fe@MF-12.5-800 exhibited the highest removal efficiency of 99% Cr(VI) (10 mg/L) at neutral pH among the carbonized melamine foam-supported nZVI composites. Its iron particles were effectively soldered onto the carbonaceous surfaces within the pore networks. Moreover, Fe@MF-12.5-800 demonstrated remarkable stability (60%, 7 days) in an open environment compared with nZVI particles.

| S-EPMC9181856 | biostudies-literature

Nanoscale zero-valent iron loaded vermiform expanded graphite for the removal of Cr (VI) from aqueous solution.

Project description:Cr (VI) is indispensable in industrial manufacturing, and its extensive use leads to severe heavy-metal pollution in the water environment around people, posing a great danger to physical health and living environment of multitudinous organisms. Expanded graphite (EG) is considered as a typical material for adsorption, while nanoscale zero-valent iron (nZVI) can be applied to degrade and sedimentate various organic or inorganic pollutants. In this study, a simultaneous collaboration of EG and nZVI is carried out, with the investigation on the influence of different test conditions for adsorption performances. These findings demonstrate that nZVI@EG manifests favourable adsorptive performance on the removal of hexavalent chromium efficiently. nZVI, acting as an electron donor, is supposed to reduce Cr (VI) to Cr (III), turning itself into iron oxide or hydroxide. The whole process is an exothermic reaction, accompanying chemical reduction and physical adsorption. And Cr (III) is fastened on the appearance by deposition of chromium hydroxide or ferrochromium complex precipitation, which greatly reduces the total chromium content in the aqueous solution. Herein, as a new composite adsorbent, nZVI@EG shows promising prospects of practical applications in water contamination and environmental remediation.

| S-EPMC8371360 | biostudies-literature

Co-Removal Effect and Mechanism of Cr(VI) and Cd(II) by Biochar-Supported Sulfide-Modified Nanoscale Zero-Valent Iron in a Binary System.

Project description:This study aimed to explore the co-removal effect and mechanism of Cr(VI) and Cd(II) with an optimized synthetic material. The toxicity and accumulation characteristics of Cr(VI) and Cd(II) encountered in wastewater treatment areas present significant challenges. In this work, a rational assembly of sulfide-modified nanoscale zero-valent iron (SnZVI) was introduced into a biochar (BC), and a Cr(VI)-Cd(II) binary system adsorbent with high efficiency was synthesized. When the preparation temperature of the BC was 600 °C, the molar ratio of S/Fe was 0.3, the mass ratio of BC/SnZVI was 1, and the best adsorption capacities of BC-SnZVI for Cr(VI) and Cd(II) in the binary system were 58.87 mg/g and 32.55 mg/g, respectively. In addition, the adsorption mechanism of BC-SnZVI on the Cr(VI)-Cd(II) binary system was revealed in depth by co-removal experiments, indicating that the coexistence of Cd(II) could promote the removal of Cr(VI) by 9.20%, while the coexistence of Cr(VI) could inhibit the removal of Cd(II) by 43.47%. This work provides a new pathway for the adsorption of Cr(VI) and Cd(II) in binary systems, suggesting that BC-SnZVI shows great potential for the co-removal of Cr(VI) and Cd(II) in wastewater.

| S-EPMC9331559 | biostudies-literature

Remediation of Cr(VI)-Contaminated Soil by Biochar-Supported Nanoscale Zero-Valent Iron and the Consequences for Indigenous Microbial Communities.

Project description:Biochar/nano-zero-valent iron (BC-nZVI) composites are currently of great interest as an efficient remediation material for contaminated soil, but their potential to remediate Cr-contaminated soils and effect on soil microecology is unclear. The purpose of this study was to investigate the effect of BC-nZVI composites on the removal of Cr(VI) from soil, and indigenous microbial diversity and community composition. The results showed that after 15 days of remediation with 10 g/kg of BC-nZVI, 86.55% of Cr(VI) was removed from the soil. The remediation of the Cr-contaminated soil with BC-nZVI resulted in a significant increase in OTUs and α-diversity index, and even a significant increase in the abundance and diversity of indigenous bacteria and unique bacterial species in the community by reducing the toxic concentration of Cr, changing soil properties, and providing habitat for survival. These results confirm that BC-nZVI is effective in removing Cr(VI) and stabilizing Cr in soil with no significant adverse effects on soil quality or soil microorganisms.

| S-EPMC9565499 | biostudies-literature

Synthesis and Characterization of Reduced Graphene Oxide-Supported Nanoscale Zero-Valent Iron (nZVI/rGO) Composites Used for Pb(II) Removal.

Project description:Reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) composites were prepared by chemical deposition method and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, N?-sorption and X-ray photoelectron spectroscopy (XPS). Operating parameters for the removal process of Pb(II) ions, such as temperature (20-40 °C), pH (3-5), initial concentration (400-600 mg/L) and contact time (20-60 min), were optimized using a quadratic model. The coefficient of determination (R² > 0.99) obtained for the mathematical model indicates a high correlation between the experimental and predicted values. The optimal temperature, pH, initial concentration and contact time for Pb(II) ions removal in the present experiment were 21.30 °C, 5.00, 400.00 mg/L and 60.00 min, respectively. In addition, the Pb(II) removal by nZVI/rGO composites was quantitatively evaluated by using adsorption isotherms, such as Langmuir and Freundlich isotherm models, of which Langmuir isotherm gave a better correlation, and the calculated maximum adsorption capacity was 910 mg/g. The removal process of Pb(II) ions could be completed within 50 min, which was well described by the pseudo-second order kinetic model. Therefore, the nZVI/rGO composites are suitable as efficient materials for the advanced treatment of Pb(II)-containing wastewater.

| S-EPMC5512353 | biostudies-literature

Carbothermal Synthesis of Sludge Biochar Supported Nanoscale Zero-Valent Iron for the Removal of Cd2+ and Cu2+: Preparation, Performance, and Safety Risks.

Project description:The practical application of nanoscale zero-valent iron (NZVI) is restricted by its easy oxidation and aggregation. Here, sludge biochar (SB) was used as a carrier to stabilize NZVI for Cd2+ and Cu2+ removal. SB supported NZVI (SB-NZVI) was synthesized using the carbothermic method. The superior preparation conditions, structural characteristics, and performance and mechanisms of the SB-NZVI composites for the removal of Cd2+ and Cu2+ were investigated via batch experiments and characterization analysis. The optimal removal capacities of 55.94 mg/g for Cd2+ and 97.68 mg/g for Cu2+ were achieved at a Fe/sludge mass ratio of 1:4 and pyrolysis temperature of 900 °C. Batch experiments showed that the SB-NZVI (1:4-900) composite had an excellent elimination capacity over a broad pH range, and that weakly acidic to neutral solutions were optimal for removal. The XPS results indicated that the Cd2+ removal was mainly dependent on the adsorption and precipitation/coprecipitation, while reduction and adsorption were the mechanisms that play a decisive role in Cu2+ removal. The presence of Cd2+ had an opposite effect on the Cu2+ removal. Moreover, the SB-NZVI composites made of municipal sludge greatly reduces the leaching toxicity and bio-availability of heavy metals in the municipal sludge, which can be identified as an environmentally-friendly material.

| S-EPMC9740856 | biostudies-literature

Effective removal of Cr(vi) from aqueous solution by biochar supported manganese sulfide.

Project description:In order to remove hexavalent chromium (Cr(vi)) efficiently and simplify the adsorbent preparation process, we employed a single step method to prepare a new biochar supported manganese sulfide material. The nanoscale MnS particles were highly soldered on the biochar support surface, and this adsorbent displayed the effective removal of Cr(vi) (98.15 mg L-1) via synergistic effect between adsorption and reduction/precipitation under weak acid conditions (pH = 5.0-6.0). The adsorption kinetic data were described well by the pseudo second-order kinetic model, suggesting that the reaction process was a chemisorption process. The adsorption isotherm data were described well by the Redlich-Peterson model, further suggesting that this reaction was a hybrid chemical reaction-sorption process. In addition, the Dubinin-Radushkevich isotherm model with 8.28, 8.57, and 12.91 kJ mol-1 adsorption energy also suggests that it was a chemisorption process. The simple and eco-friendly preparation process, low-cost, and the high removal efficiency could make it a promising material for the purification of Cr(vi)-contaminated wastewater.

| S-EPMC9072298 | biostudies-literature

Preparation of Activated Carbon Supported Bead String Structure Nano Zero Valent Iron in a Polyethylene Glycol-Aqueous Solution and Its Efficient Treatment of Cr(VI) Wastewater.

Project description:Nanometer zero-valent iron (nZVI) has been widely used in the treatment of heavy metals such as hexavalent chromium (Cr(VI)). A novel composite of bead string-structured nZVI on modified activated carbon (nZVI-MAC) is prepared here, using polyethylene glycol as the stable dispersant rather than traditional ethanol during the loading process. The microstructure characterization shows that nZVI particles are loaded on MAC with a bead string structure in large quantity and stably due to the addition of hydroxyl functional groups on the surface by polyethylene glycol. Experiments on the treatment of Cr(VI) in wastewater show that the reaction process requires only 20 min to achieve equilibrium. The removal rate of Cr(VI) with a low concentration (80-100 mg/L) is over 99% and the maximum saturation removal capacity is up to 66 mg/g. The system converts Cr(VI) to trivalent chromium (Cr(III)) through an oxidation-reduction effect and forms an insoluble material with iron ions by coprecipitation, which is then adsorbed on the surface of the nZVI-MAC. The process conforms to the quasi-second order adsorption kinetics equation (mainly chemical adsorption process).

| S-EPMC6982729 | biostudies-literature

Dissolved Selenium(VI) Removal by Zero-Valent Iron under Oxic Conditions: Influence of Sulfate and Nitrate.

Project description:Dissolved Se(VI) removal by three commercially available zero-valent irons (ZVIs) was examined in oxic batch experiments under circumneutral pH conditions in the presence and absence of NO3 - and SO4 2-. Environmentally relevant Se(VI) (1 mg L-1), NO3 - ([NO3-N] = 15 mg L-1), and SO4 2- (1800 mg L-1) were employed to simulate mining-impacted waters. Ninety percent of Se(VI) removal was achieved within 4-8 h in the absence of SO4 2- and NO3 -. A similar Se(VI) removal rate was observed after 10-32 h in the presence of NO3 -. Dissolved Se(VI) removal rates exhibited the highest decrease in the presence of SO4 2-; 90% of Se(VI) removal was measured after 50-191 h for SO4 2- and after 150-194 h for SO4 2- plus NO3 - depending on the ZVI tested. Despite differences in removal rates among batches and ZVI materials, Se(VI) removal consistently followed first-order reaction kinetics. Scanning electron microscopy, Raman spectroscopy, and X-ray diffraction analyses of reacted solids showed that Fe(0) present in ZVI undergoes oxidation to magnetite [Fe3O4], wüstite [FeO], lepidocrocite [γ-FeOOH], and goethite [α-FeOOH] over time. X-ray absorption near-edge structure spectroscopy indicated that Se(VI) was reduced to Se(IV) and Se(0) during removal. These results demonstrate that ZVI can be effectively used to control Se(VI) concentrations in mining-impacted waters.

| S-EPMC6640955 | biostudies-literature

Evaluation on the Nanoscale Zero Valent Iron Based Microbial Denitrification for Nitrate Removal from Groundwater.

Project description:Nanoscale zero valent iron (NZVI) based microbial denitrification has been demonstrated to be a promising technology for nitrate removal from groundwater. In this work, a mathematical model is developed to evaluate the performance of this new technology and to provide insights into the chemical and microbial interactions in the system in terms of nitrate reduction, ammonium accumulation and hydrogen turnover. The developed model integrates NZVI-based abiotic reduction of nitrate, NZVI corrosion for hydrogen production and hydrogen-based microbial denitrification and satisfactorily describes all of the nitrate and ammonium dynamics from two systems with highly different conditions. The high NZVI corrosion rate revealed by the model indicates the high reaction rate of NZVI with water due to their large specific surface area and high surface reactivity, leading to an effective microbial nitrate reduction by utilizing the produced hydrogen. The simulation results further suggest a NZVI dosing strategy (3-6 mmol/L in temperature range of 30-40 °C, 6-10 mmol/L in temperature range of 15-30 °C and 10-14 mmol/L in temperature range of 5-15 °C) during groundwater remediation to make sure a low ammonium yield and a high nitrogen removal efficiency.

| S-EPMC4510576 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data