Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Thermal Fatigue Behavior of Air-Plasma Sprayed Thermal Barrier Coating with Bond Coat Species in Cyclic Thermal Exposure.

ABSTRACT: The effects of the bond coat species on the delamination or fracture behavior in thermal barrier coatings (TBCs) was investigated using the yclic thermal fatigue and thermal-shock tests. The interface microstructures of each TBC showed a good condition without cracking or delamination after flame thermal fatigue (FTF) for 1429 cycles. The TBC with the bond coat prepared by the air-plasma spray (APS) method showed a good condition at the interface between the top and bond coats after cyclic furnace thermal fatigue (CFTF) for 1429 cycles, whereas the TBCs with the bond coats prepared by the high-velocity oxygen fuel (HVOF) and low-pressure plasma spray (LPPS) methods showed a partial cracking (and/or delamination) and a delamination after 780 cycles, respectively. The TBCs with the bond coats prepared by the APS, HVOF and LPPS methods were fully delaminated (>50%) after 159, 36, and 46 cycles, respectively, during the thermal-shock tests. The TGO thickness in the TBCs was strongly dependent on the both exposure time and temperature difference tested. The hardness values were found to be increased only after the CFTF, and the TBC with the bond coat prepared by the APS showed the highest adhesive strength before and after the FTF.

SUBMITTER: Lu Z

PROVIDER: S-EPMC5521311 | biostudies-other | 2013 Aug

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Corrosion Behavior of Detonation Gun Sprayed Fe-Al Type Intermetallic Coating.

Project description:The detonation gun sprayed Fe-Al type coatings as an alternative for austenitic valve steel, were investigated using two different methods of testing corrosion resistance. High temperature, 10-hour isothermal oxidation experiments at 550, 750, 950 and 1100 °C show differences in the oxidation behavior of Fe-Al type coatings under air atmosphere. The oxide layer ensures satisfying oxidation resistance, even at 950 and 1100 °C. Hematite, α-Al₂O₃ and metastable alumina phases were noticed on the coatings top surface, which preserves its initial thickness providing protection to the underlying substrate. In general, only negligible changes of the phase composition of the coatings were noticed with simultaneous strengthening controlled in the micro-hardness measurements, even after 10-hours of heating at 1100 °C. On the other hand, the electrochemical corrosion tests, which were carried out in 200 ppm Cl- (NaCl) and pH ~4 (H₂SO₄) solution to simulate the acid-rain environment, reveal higher values of the breakdown potential for D-gun sprayed Fe-Al type coatings than the ones for the bulk Fe-Al type alloy and Cr21Mn9Ni4 austenitic valve steel. This enables these materials to be used in structural and multifunctional applications in aggressive environments, including acidic ones.

| S-EPMC5455446 | biostudies-other

Molten-Volcanic-Ash-Phobic Thermal Barrier Coating based on Biomimetic Structure.

Project description:Volcanic ash is a major threat to aviation safety. The softening/melting temperatures of volcanic ash lie far below typical aero-engine operating temperatures. Thus, molten ash can accelerate the failure of thermal barrier coatings (TBCs). Here, inspired by natural superhydrophobic surfaces (e.g., the lotus leaf), a molten-volcanic-ash-phobic TBC, which provides a large possibility to eliminate molten ash issues of TBCs, is developed. A hierarchically structured surface is first prepared on a (Gd0.9 Yb0.1 )2 Zr2 O7 (GYbZ) pellet by ultrafast laser direct writing technology, aiming to confirm the feasibility of the biomimetic microstructure to repel molten volcanic ash wetting. Then biomimetic-structured GYbZ TBCs are successfully fabricated using plasma spray physical vapor deposition, which reveals "silicate" phobicity at high temperatures. The exciting molten-volcanic-ash-phobic attribute of the designed surfaces is attributed to the lotus-leaf-like dual-scale microstructure, emulating in particular the existence of nanoparticles. These findings may be an important step toward the development of next-generation aviation engines with greatly reduced vulnerability to environmental siliceous debris.

| S-EPMC10074056 | biostudies-literature

A study on thermal behaviour of thermal barrier coating: investigation of particle size, YSZ/polysilazane, time and temperature curing effect.

Project description:Thermal conductivity and adhesion strength effects were studied for thermal barrier coatings (TBCs) with different particle sizes, YSZ content, time, and temperature curing. The study involves three stages. The first step focuses on the characteristics of YSZ/polysilazane as the TBC, which is characterized using Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR), X-Ray Diffraction (XRD), and Thermal Gravimetric Analysis (TGA). The second and third steps assess thermal conductivity and adhesion strength based on variables such as particle size, YSZ/polysilazane, time, and curing temperature. Results show that there was a synergistic effect between particle size-YSZ content and time-temperature curing to obtain specimens with good thermal properties. SB270/70 showed the lowest temperature compared to other specimens, up to 160 °C. Furthermore, YSZ/polysilazane thermal conductivity and adhesion properties could be enhanced by a prolonged curing time and higher temperature. This study emphasizes that the modification of particle size, YSZ content, time, and temperature curing is a promising strategy to improve the thermal properties of TBCs.

| S-EPMC11302517 | biostudies-literature

Extraordinary thermal behavior of graphene oxide in air for electrode applications.

Project description:The thermal stability of solution-exfoliated graphene oxide (GO) in air is one of the most important physical properties influencing its potential applications. To date, the majority of the GO prepared by the KMnO4-based oxidation of graphite is thermally unstable in air due to the presence of highly oxidative functional groups, such as carboxyl and lactol groups that possess defective basal plane structures. Here, we demonstrate that less defective and metal ion-free GO nanosheets including those with a high oxidation level can remain very stable even above 300 °C under ambient conditions. These GO nanosheets were produced by the exfoliation of graphite oxide fabricated by the modified Brodie method in NH4OH solution, effectively excluding metal ions that can promote the thermal decomposition of GO in air at elevated temperatures. The deoxygenation of ammonia-assisted GO (AGO) was initiated at temperatures above 200 °C, while GO exfoliated in the KOH solution (KGO) decomposed, even at 180 °C. Notably, AGO was exceptionally resistant at 400 °C, even at a very slow heating rate of 2 °C min-1. Conversely, KGO was significantly oxidized, even at 250 °C. The superior thermal stability of AGO is favorable for the fabrication of conductive surface graphene films and conductive fibers by low-temperature annealing.

| S-EPMC9417645 | biostudies-literature

Nanocomposite Sprayed Films with Photo-Thermal Properties for Remote Bacteria Eradication.

Project description:Currently there is a strong demand for novel protective materials with efficient antibacterial properties. Nanocomposite materials loaded with photo-thermally active nanoparticles can offer promising opportunities due to the local increase of temperature upon near-infrared (NIR) light exposure capable of eradicating bacteria. In this work, we fabricated antibacterial films obtained by spraying on glass slides aqueous solutions of polymers, containing highly photo-thermally active gold nanostars (GNS) or Prussian Blue (PB) nanoparticles. Under NIR light irradiation with low intensities (0.35 W/cm2) these films demonstrated a pronounced photo-thermal effect: ?Tmax up to 26.4 °C for the GNS-containing films and ?Tmax up to 45.8 °C for the PB-containing films. In the latter case, such a local temperature increase demonstrated a remarkable effect on a Gram-negative strain (P. aeruginosa) killing (84% of dead bacteria), and a promising effect on a Gram-positive strain (S. aureus) eradication (69% of dead bacteria). The fabricated films are promising prototypes for further development of lightweight surfaces with efficient antibacterial action that can be remotely activated on demand.

| S-EPMC7221876 | biostudies-literature

Robust Hydrophobic Surfaces from Suspension HVOF Thermal Sprayed Rare-Earth Oxide Ceramics Coatings.

Project description:This study has presented an efficient coating method, namely suspension high velocity oxy-fuel (SHVOF) thermal spraying, to produce large super-hydrophobic ceramic surfaces with a unique micro- and nano-scale hierarchical structures to mimic natural super-hydrophobic surfaces. CeO2 was selected as coatings material, one of a group of rare-earth oxide (REO) ceramics that have recently been found to exhibit intrinsic hydrophobicity, even after exposure to high temperatures and abrasive wear. Robust hydrophobic REO ceramic surfaces were obtained from the deposition of thin CeO2 coatings (3-5 μm) using an aqueous suspension with a solid concentration of 30 wt.% sub-micron CeO2 particles (50-200 nm) on a selection of metallic substrates. It was found that the coatings' hydrophobicity, microstructure, surface morphology, and deposition efficiency were all determined by the metallic substrates underneath. More importantly, it was demonstrated that the near super-hydrophobicity of SHVOF sprayed CeO2 coatings was achieved not only by the intrinsic hydrophobicity of REO but also their unique hierarchically structure. In addition, the coatings' surface hydrophobicity was sensitive to the O/Ce ratio, which could explain the 'delayed' hydrophobicity of REO coatings.

| S-EPMC5934356 | biostudies-literature

Effect of NaCl Pretreatment on the Relationship between the Color Characteristics and Taste of <i>Cirsium setidens</i> Processed Using a Micro-Oil-Sprayed Thermal Air Technique.

Project description:Cirsium setidens is commonly used as a food ingredient, and it is typically stored and distributed in a dried form to prolong its shelf life. In a previous study, a micro-oil-sprayed thermal air (MOTA) technique was developed, which effectively enhanced the rehydration properties and improved the color characteristics of Cirsium setidens after processing. Here, we investigated the relationship between the color characteristics and taste of MOTA-processed C. setidens and the effect of NaCl pretreatment, prior to processing, on the final quality of dried C. setidens. NaCl pretreatment, whether combined with the MOTA technique or not, showed improved color characteristics, in which MOTA-and NaCl+ MOTA-processed C. setidens manifested equal color characteristics. In contrast, NaCl + MOTA-processed C. setidens resulted in significantly higher values of sourness and saltiness than MOTA-processed C. setidens when the taste of the rehydrated C. setidens was examined using an electronic tongue (Astree II; Alpha MOS, Toulouse, France). Pearson correlation coefficient analysis showed that sourness and saltness were negatively correlated with Hunter a* values and positively correlated with Hunter L* and Hunter b* values, indicating that the color characteristics of dried and rehydrated C. setidens could be indicators of taste. Furthermore, the amounts of total phenol and chlorophyll were better preserved in C. setidens processed by the MOTA technique with NaCl than by the MOTA technique alone. Our data revealed that the color characteristics of dried plants are associated with the taste of processed C. setidens, and that the MOTA technique with NaCl pretreatment is a useful method for preserving health-promoting compounds during processing.

| S-EPMC10535967 | biostudies-literature

A Theoretical Model for Predicting Residual Stress Generation in Fabrication Process of Double-Ceramic-Layer Thermal Barrier Coating System.

Project description:Residual stress arisen in fabrication process of Double-Ceramic-Layer Thermal Barrier Coating System (DCL-TBCs) has a significant effect on its quality and reliability. In this work, based on the practical fabrication process of DCL-TBCs and the force and moment equilibrium, a theoretical model was proposed at first to predict residual stress generation in its fabrication process, in which the temperature dependent material properties of DCL-TBCs were incorporated. Then, a Finite Element method (FEM) has been carried out to verify our theoretical model. Afterwards, some important geometric parameters for DCL-TBCs, such as the thickness ratio of stabilized Zirconia (YSZ, ZrO2-8%Y2O3) layer to Lanthanum Zirconate (LZ, La2Zr2O7) layer, which is adjustable in a wide range in the fabrication process, have a remarkable effect on its performance, therefore, the effect of this thickness ratio on residual stress generation in the fabrication process of DCL-TBCs has been systematically studied. In addition, some thermal spray treatment, such as the pre-heating treatment, its effect on residual stress generation has also been studied in this work. It is found that, the final residual stress mainly comes from the cooling down process in the fabrication of DCL-TBCs. Increasing the pre-heating temperature can obviously decrease the magnitude of residual stresses in LZ layer, YSZ layer and substrate. With the increase of the thickness ratio of YSZ layer to LZ layer, magnitudes of residual stresses arisen in LZ layer and YSZ layer will increase while residual stress in substrate will decrease.

| S-EPMC5245788 | biostudies-other

Analysis of Thermal Behavior of Crystalline Minerals in Bituminous Coal Samples under Air and Argon Atmospheres.

Project description:The thermal behavior of ash components in two bituminous coal samples [Upper Freeport (the "UF") and Illinois #6 (the "IL")] was investigated under air and argon atmospheres in the temperature range of 800-1200 °C using thermal gravimetric-differential thermal analysis, X-ray diffraction transmission electron microscopy (TEM), and TEM-energy dispersive X-ray spectrometry measurements. The UF treated under air formed the needle-like crystals which were assumed to be mullite-related substances formed by transformation of andalusite, because the crystals are mainly composed of SiO2 and Al2O3. In contrast to the UF, the IL did not generate such crystals; however, when the IL was treated under air after carbonization under Ar, crystals appeared. The composition of the UF with an Al/Si ratio higher than that of the IL favored the formation of mullite-related substances, while the presence of lime in the IL inhibited the formation of mullite-related substances. Oldhamite was formed by the reaction of lime with sulfur at the carbonization of the IL under Ar and remained even at the successive air treatment. As lime was consumed, the formation of mullite-related substances was ceased to be inhibited under air after Ar treatment.

| S-EPMC7818308 | biostudies-literature

A Temperature-Dependent Viscoplasticity Model for the Hot Work Steel X38CrMoV5-3, Including Thermal and Cyclic Softening under Thermomechanical Fatigue Loading

Project description:In this paper, a temperature-dependent viscoplasticity model is presented that describes thermal and cyclic softening of the hot work steel X38CrMoV5-3 under thermomechanical fatigue loading. The model describes the softening state of the material by evolution equations, the material properties of which can be determined on the basis of a defined experimental program. A kinetic model is employed to capture the effect of coarsening carbides and a new isotropic cyclic softening model is developed that takes history effects during thermomechanical loadings into account. The temperature-dependent material properties of the viscoplasticity model are determined on the basis of experimental data measured in isothermal and thermomechanical fatigue tests for the material X38CrMoV5-3 in the temperature range between 20 and 650

| S-EPMC9918193 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data