Dataset Information

Clinical outcome of alveolar ridge augmentation with individualized CAD-CAM-produced titanium mesh.

ABSTRACT: The augmentation of the jaw has been and continues to be a sophisticated therapy in implantology. Modern CAD-CAM technologies lead to revival of old and established augmentation techniques such as the use of titanium mesh (TM) for bone augmentation. The aim of this retrospective study was to evaluate the clinical outcome of an individualized CAD-CAM-produced TM based on the CT/DVT-DICOM data of the patients for the first time.In 17 patients, 21 different regions were augmented with an individualized CAD-CAM-produced TM (Yxoss CBR®, Filderstadt, Germany). For the augmentation, a mixture of autologous bone and deproteinized bovine bone mineral (DBBM) or autologous bone alone was used. Reentry with explantation of the TM and simultaneous implantation of 44 implants were performed after 6 months. Preoperative and 6-month postoperative cone beam computed tomographies (CBCT) were performed to measure the gained bone height.The success rate for the bone grafting procedure was 100%. Thirty-three percent of cases presented an exposure of the TM during the healing period. However, premature removal of these exposed meshes was not necessary. Exposure rate in augmentations performed with mid-crestal incisions was higher than in augmentations performed with a modified poncho incision (45.5 vs. 20%, p = 0.221). In addition, exposure rates in the maxilla were significantly higher than in the mandible (66.7 vs. 8.3%, p = 0.009). Gender, smoking, periodontal disease, gingiva type, used augmentation material, and used membrane had no significant influence on the exposure rate (p > 0.05). The mean vertical augmentation was 6.5 ± 1.7 mm, and the mean horizontal augmentation was 5.5 ± 1.9 mm. Implant survival rate after a mean follow-up of 12 ± 6 months after reentry was 100%.Within the limits of the retrospective character of this study, this study shows for the first time that individualized CAD-CAM TM provide a sufficient and safe augmentation technique, especially for vertical and combined defects. However, the soft tissue handling for sufficient mesh covering remains one of the most critical steps using this technique.

SUBMITTER: Sagheb K

PROVIDER: S-EPMC5529307 | biostudies-other | 2017 Dec

REPOSITORIES: biostudies-other

ACCESS DATA

Similar Datasets

Project description:BackgroundThere is limited information on the need for bone augmentation in the context of delayed implant placement whether alveolar ridge preservation (ARP) is previously performed or not. The primary aim of this retrospective cohort study was to evaluate the efficacy of ARP therapy after tooth extraction compared with unassisted socket healing (USH) in reducing the need for ancillary bone augmentation before or at the time of implant placement.MethodsAdult subjects that underwent non-molar single tooth extraction with or without simultaneous ARP therapy were included in this study. Cone beam computed tomography scans obtained before tooth extraction and after a variable healing period were used to record the baseline facial bone thickness and to virtually plan implant placement according to a standard method. A logistic regression model was used to evaluate the effect of facial alveolar bone thickness upon tooth extraction and baseline therapy (USH or ARP) on the need for additional bone augmentation, adjusting for several covariates (i.e., age, sex, baseline KMW, and tooth type).ResultsOne hundred and forty subjects that were equally distributed between both baseline therapy groups constituted the study population. Implant placement was deemed virtually feasible in all study sites. Simultaneous bone augmentation was considered necessary in 60% and 11.4% of the sites in the USH and ARP group, respectively. Most of these sites (64.2% in the USH group and 87.5% in the ARP group) exhibited a thin facial bone phenotype (<1 mm) at baseline. Logistic regression revealed that the odds of not needing ancillary bone augmentation were 17.8 times higher in sites that received ARP therapy. Furthermore, the need for additional bone augmentation was reduced 7.7 times for every 1 mm increase in facial bone thickness, regardless of baseline therapy.ConclusionsBased on a digital analysis, ARP therapy, compared with USH, and thick facial alveolar bone largely reduce the need for ancillary bone augmentation at the time of implant placement in non-molar sites.

Dataset Information

Clinical outcome of alveolar ridge augmentation with individualized CAD-CAM-produced titanium mesh.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets