Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Enhancing the Compatibility of Poly (1,4-butylene adipate) and Phenoxy Resin in Blends.

ABSTRACT: This work concerns the enhancement in the compatibility of blends of poly (1,4-butylene adipate) (PBA) with poly (hydroxy ether of bisphenol-A) (phenoxy) via alcoholytic exchange. Results on the thermal behavior and morphology show that the blended PBA/phenoxy system exhibits a homogeneous phase and a composition-dependent glass transition temperature (Tg). The interaction parameter (χ12) of PBA/phenoxy blends was calculated using the melting point depression method and was found to be -0.336. However, the compatibilization of PBA/phenoxy blends can be enhanced by chemical exchange reactions between PBA and phenoxy upon annealing. Annealed PBA/phenoxy blends were found to have a homogeneous phase with a higher Tg than that of the blended samples, and a smooth surface topography that could be improved by annealing at high temperature. The results of this investigation demonstrate that promotional phase compatibilization in the PBA/phenoxy blend can only be obtained upon thermal annealing, thus causing transreactions to occur between the dangling -OH of the phenoxy and the ester functional groups in PBA. Extensive transreactions cause alcoholytic exchange between the PBA and phenoxy to form a network, thus reducing the mobility of the polymer chain. Finally, the crystallinity of PBA decreased as the degree of transreaction in the blends increased.

SUBMITTER: Yang CF

PROVIDER: S-EPMC5551735 | biostudies-other | 2017 Jun

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Tuning the compatibility to achieve toughened biobased poly(lactic acid)/poly(butylene terephthalate) blends.

Project description:A series of sustainable biobased polymer blends from poly(lactic acid) (PLA) and poly(butylene terephthalate) (PBT) were fabricated and characterized. These blends are engineered to achieve optimal mechanical properties and toughness with a reactive epoxidized styrene-acrylic copolymer (ESAC) compatibilizer, and an ethylene-n-butyl-acrylate-co-glycidyl methacrylate (EBA-GMA) elastomer-based compatibilizer. The results showed that the tensile strength, modulus, flexural strength and modulus of the PBT increase, while the elongation at break and notched impact strength decrease after blending with the biopolymer PLA. The full co-continuity of PLA in PBT was confirmed at a 50/50 wt% blend ratio. The droplet size of the PLA was reduced and the distinct phases of the blends were gradually diminished with the increasing content of the ESAC compatibilizer. The increase in the complex viscosity of the blends was due to the formation of PLA-g-PBT copolymers in the blend after addition of reactive compatibilizers. The incorporation of both compatibilizers in the blends led to superior notched impact strength in comparison to only a single compatibilizer used in the blends. The synergistic effect of both compatibilizers effectively reduces the PLA droplet size and improves the dispersion of PLA in PBT as evidenced by atomic force microscopy (AFM) topography observations. The high toughness of the blends corresponds to the formation of effective EBA-GMA structures and enhanced interfacial compatibilization due to the synergistic effect of the compatibilizers.

| S-EPMC9083900 | biostudies-literature

Super Toughened Poly(lactic acid)-Based Ternary Blends via Enhancing Interfacial Compatibility.

Project description:Novel super toughened bioplastics are developed through controlled reactive extrusion processing, using a very low content of modifier, truly a new discovery in the biodegradable plastics area. The super toughened polylactide (PLA) blend showing a notched impact strength of ∼1000 J/m with hinge break behavior is achieved at a designed blending ratio of PLA, poly(butylene succinate) (PBS), and poly(butylene adipate-co-terephthalate) (PBAT), using less than 0.5 phr peroxide modifier. The impact strength of the resulting blend is approximately 10 times that of the blend with the same composition without a modifier and ∼3000% more than that of pure PLA. Interfacial compatibilization among the three biodegradable plastics took place during the melt extrusion process in the presence of a controlled amount of initiator, which is confirmed by scanning electron microscopy and rheology analysis. The synergistic effect of strong interfacial adhesion among the three blending components, the decreased particle size of the most toughened component, PBAT, to ∼200 nm, and its uniform distribution in the blend morphology result in the super tough biobased material. One of the key fundamental findings through the in situ rheology study depicts that the radical reaction initiated by peroxide occurs mainly between PBS and PBAT and not with PLA. Thus, the cross-linking degree can be controlled by adjusting renewable sourced PLA contents in the ternary blend during reactive extrusion processing. The newly engineered super toughened PLA with high stiffness and high melt elasticity modulus could reasonably serve as a promising alternative to traditional petroleum plastics, where high biobased content and biodegradability are required in diverse sustainable packaging uses.

| S-EPMC6648285 | biostudies-literature

Bio-Based Poly(lactic acid)/Poly(butylene sebacate) Blends with Improved Toughness.

Project description:A series of poly(butylene sebacate) (PBSe) aliphatic polyesters were successfully synthesized by the melt polycondensation of sebacic acid (Se) and 1,4-butanediol (BDO), two monomers manufactured on an industrial scale from biomass. The number average molecular weight (Mn) in the range from 6116 to 10,779 g/mol and the glass transition temperature (Tg) of the PBSe polyesters were tuned by adjusting the feed ratio between the two monomers. Polylactic acid (PLA)/PBSe blends with PBSe concentrations between 2.5 to 20 wt% were obtained by melt compounding. For the first time, PBSe's effect on the flexibility and toughness of PLA was studied. As shown by the torque and melt flow index (MFI) values, the addition of PBSe endowed PLA with both enhanced melt processability and flexibility. The tensile tests and thermogravimetric analysis showed that PLA/PBSe blends containing 20 wt% PBSe obtained using a BDO molar excess of 50% reached an increase in elongation at break from 2.9 to 108%, with a negligible decrease in Young's modulus from 2186 MPa to 1843 MPa, and a slight decrease in thermal performances. These results demonstrated the plasticizing efficiency of the synthesized bio-derived polyesters in overcoming PLA's brittleness. Moreover, the tunable properties of the resulting PBSe can be of great industrial interest in the context of circular bioeconomy.

| S-EPMC9572606 | biostudies-literature

Properties of Biodegradable Films Based on Poly(butylene Succinate) (PBS) and Poly(butylene Adipate-co-Terephthalate) (PBAT) Blends †,‡.

Project description:Compression molded biodegradable films based on poly(butylene succinate) (PBS) and poly(butylene adipate-co-terephthalate) (PBAT) at varying weights were prepared, and their relevant properties for packaging applications are here reported. The melt rheology of the blends was first studied, and the binary PBS/PBAT blends exhibited marked shear thinning and complex thermoreological behavior, due to the formation of a co-continuous morphology in the 50 wt% blend. The films were characterized by infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), mechanical tensile tests, scanning electron microscopy (SEM), and oxygen and water vapor permeability. PBS crystallization was inhibited in the blends with higher contents of PBAT, and FTIR and SEM analysis suggested that limited interactions occur between the two polymer phases. The films showed increasing stiffness as the PBS percentage increased; further, a sharp decrease in elongation at break was noticed for the films containing percentages of PBS greater than 25 wt%. Gas permeability decreased with increasing PBS content, indicating that the barrier properties of PBS can be tuned by blending with PBAT. The results obtained point out that the blend containing 25 wt% PBS is a good compromise between elastic modulus (135 MPa) and deformation at break (390%) values. Overall, PBS/PBAT blends represent an alternative for packaging films, as they combine biodegradability, good barrier properties and reasonable mechanical behavior.

| S-EPMC7600530 | biostudies-literature

Self-Healing and Mechanical Properties of Thermoplastic Polyurethane/Eugenol-Based Phenoxy Resin Blends via Exchange Reactions.

Project description:The possibility of exchange reactions and thermal self-healing in blends of thermoplastic polyurethane (TPU) and phenoxy resin was investigated herein. The analyses were based on characterization obtained via differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and tensile test. A new phenoxy resin was synthesized from eugenol, and blends with different types of TPU were prepared to investigate the exchange reaction, thermal self-healing, and mechanical properties. The influence of phenoxy resin content on the mechanical behavior and healing efficiency was studied. Improvement of storage modulus owing to the increase of phenoxy resin content was observed. Results suggest that the exchange reaction between phenoxy- and ester-type TPU occurred during thermal treatment. However, little exchange occurred between phenoxy resin and ether-type TPU. Specifically, only ester-type TPU exhibited a significant exchange reaction in the phenoxy resin blend. Furthermore, in the presence of a catalyst (e.g., zinc acetate), the exchange reaction readily occurred, and the healing efficiency improved by the addition of the catalyst and increase in the phenoxy content.

| S-EPMC7284341 | biostudies-literature

Nucleation of Poly(lactide) Partially Wet Droplets in Ternary Blends with Poly(butylene succinate) and Poly(ε-caprolactone).

Project description:This work presents the first investigation on the crystallization behavior of partially wet droplets in immiscible ternary blends. Poly(lactide), poly(ε-caprolactone), and poly(butylene succinate) (PLA, PCL, and PBS, respectively) were melt blended in a 10/45/45 weight ratio to produce a "partial wetting" morphology with droplets of the PLA minor phase located at the interface between the other two major components. The crystallization process of the higher melting PLA droplets was studied by polarized light optical microscopy, while the other components remain in the molten state. We found that neighboring partially wet droplets nucleate in close sequence. This is unexpected since partially wet droplets display points of three-phase contact and, hence, should not touch each other. Moreover, the onset of poly(lactide) crystallization is frequently observed at the interface with molten PCL or PBS, with a significant preference for the former polymer. The observed sequential droplet-to-droplet crystallization is attributed to the weak partial wetting behavior of the PCL/PLA/PBS ternary system. In fact, the contact between the interfacially confined droplets during crystallization due to their mobility can lead to a transition from a partial to a completely wet state, with the formation of thin continuous layers bridging larger partially wet droplets. This allows crystallization to spread sequentially between neighboring domains. Using a simple heterogeneous nucleation model, it is shown that the nucleation of PLA on either PCL or PBS melts is energetically feasible. This study establishes a clear relationship between the unique partial wetting morphology of ternary blends and the nucleation of the minor component, paving the way to the understanding and control of crystallization in multiphasic polymer blends for advanced applications.

| S-EPMC8016171 | biostudies-literature

Thermoplastic Starch with Poly(butylene adipate-<i>co</i>-terephthalate) Blends Foamed by Supercritical Carbon Dioxide.

Project description:Starch-based biodegradable foams with a high starch content are developed using industrial starch as the base material and supercritical CO2 as blowing or foaming agents. The superior cushioning properties of these foams can lead to competitiveness in the market. Despite this, a weak melting strength property of starch is not sufficient to hold the foaming agents within it. Due to the rapid diffusion of foaming gas into the environment, it is difficult for starch to maintain pore structure in starch foams. Therefore, producing starch foam by using supercritical CO2 foaming gas faces severe challenges. To overcome this, we have synthesized thermoplastic starch (TPS) by dispersing starch into water or glycerin. Consecutively, the TPS surface was modified by compatibilizer silane A (SA) to improve the dispersion with poly(butylene adipate-co-terephthalate) (PBAT) to become (TPS with SA)/PBAT composite foam. Furthermore, the foam-forming process was optimized by varying the ratios of TPS and PBAT under different forming temperatures of 85 °C to 105 °C, and two different pressures, 17 Mpa and 23 Mpa were studied in detail. The obtained results indicate that the SA surface modification on TPS can influence the great compatibility with PBAT blended foams (foam density: 0.16 g/cm3); whereas unmodified TPS and PBAT (foam density: 0.349 g/cm3) exhibit high foam density, rigid foam structure, and poor tensile properties. In addition, we have found that the 80% TPS/20% PBAT foam can be achieved with good flexible properties. Because of this flexibility, lightweight and environment-friendly nature, we have the opportunity to resolve the strong demands from the packing market.

| S-EPMC9145724 | biostudies-literature

Introduction of stereocomplex crystallites of PLA for the solid and microcellular poly(lactide)/poly(butylene adipate-<i>co</i>-terephthalate) blends.

Project description:Solid and microcellular poly(l-lactide)/poly(butylene adipate-co-terephthalate) (PLLA/PBAT) blends with or without poly(d-lactide) (PDLA) were prepared via melt blending and batch foaming process with supercritical carbon dioxide, respectively. The introduction of PDLA on the rheological properties, crystallization behavior and dynamic mechanical properties of the PLLA matrix were investigated. The formed PLA stereocomplex between PLLA and PDLA enhanced the storage modulus and complex viscosity of PLLA/PBAT blends efficiently. Interestingly, the addition of 5 wt% or 10 wt% PDLA in the PLLA/PBAT blends was unfavorable for the PLLA crystallization behavior. The potential reason can be sc-PLA crystallites acting as the physical crosslinking points, which constrained the molecular mobility of the PLLA matrix and even blocked the nucleating effect of PBAT domains. Both the enhanced melt strength and decreased crystallinity of the PLLA matrix are favorable for the cell nucleation and growth and the gas adsorption, respectively. The designed partially foaming of PLLA/PBAT with or without PDLA was carried out to investigate the foaming mechanism. The final cell morphology of PLLA/PBAT foams exhibited typical open-cell structure mainly attributed to the soft immiscible PBAT phase as separated domains. With further addition of PDLA in the PLLA/PBAT blends, the microcellular morphology exhibited decreased average cell size and increased cell density. The sc-PLA crystallites networks in the PLLA matrix acted as cell nucleating agents, which meanwhile resisted the force of cell growth and then prevented the cell collapse.

| S-EPMC9079314 | biostudies-literature

Development of Toughened Flax Fiber Reinforced Composites. Modification of Poly(lactic acid)/Poly(butylene adipate-co-terephthalate) Blends by Reactive Extrusion Process.

Project description:The presented study focuses on the development of flax fiber (FF) reinforced composites prepared with the use of poly(lactic acid)/poly(butylene adipate-co-terephthalate)-PLA/PBAT blend system. This type of modification was aimed to increase impact properties of PLA-based composites, which are usually characterized by high brittleness. The PLA/PBAT blends preparation was carried out using melt blending technique, while part of the samples was prepared by reactive extrusion process with the addition of chain extender (CE) in the form of epoxy-functionalized oligomer. The properties of unreinforced blends was evaluated using injection molded samples. The composite samples were prepared by compression molding technique, while flax fibers reinforcement was in the form of plain fabric. The properties of the laminated sheets were investigated during mechanical test measurements (tensile, flexural, impact). Differential scanning calorimetry (DSC) analysis was used to determine the thermal properties, while dynamic mechanical thermal analysis (DMTA) and heat deflection temperature (HDT) measurements were conducted in order to measure the thermomechanical properties. Research procedure was supplemented with structure evaluation using scanning electron microscopy (SEM) analysis. The comparative study reveals that the properties of PLA/PBAT-based composites were more favorable, especially in the context of impact resistance improvement. However, for CE modified samples also the modulus and strength was improved. Structural observations after the impact tests confirmed the presence of the plastic deformation of PLA/PBAT matrix, which confirmed the favorable properties of the developed materials. The use of PBAT phase as the impact modifier strongly reduced the PLA brittleness, while the reactive extrusion process improves the fiber-matrix interactions leading to higher stiffness and strength.

| S-EPMC8003650 | biostudies-literature

Co-Polymers based on Poly(1,4-butylene 2,5-furandicarboxylate) and Poly(propylene oxide) with Tuneable Thermal Properties: Synthesis and Characterization.

Project description:Poly(ether ester)s (PEEs) represent a promising class of segmented co-polymers, nevertheless the synthesis of PEEs based on renewable 2,5-furandicarboxylic acid (FDCA) is still scarce. In this context, a series of poly(1,4-butylene 2,5-furandicarboxylate)-co-poly(poly(propylene oxide) 2,5-furandicarboxylate) co-polyesters with different composition of stiff poly(1,4-butylene 2,5-furandicarboxylate) (PBF) and soft poly(poly(propylene oxide) 2,5-furandicarboxylate) (PPOF) moieties were synthesized, via a two-step bulk polytransesterification reaction. The molar ratio of PBF/PPOF incorporated was varied (10 to 50 mol%) in order to prepare several novel materials with tuned properties. The materials were characterised in detail through several techniques, namely ATR FTIR, ¹H and 13C NMR, TGA, DSC, DMTA and XRD. Their hydrolytic and enzymatic degradation evaluation was also assessed. These new co-polymers showed either a semi-crystalline nature when higher PBF/PPOF ratios were used, and for approximately equal amounts of PBF and PPOF an amorphous co-polyester was obtained instead.

| S-EPMC6356699 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data