Microwave-Assisted Synthesis of Goethite Nanoparticles Used for Removal of Cr(VI) from Aqueous Solution.
Ontology highlight
ABSTRACT:
SUBMITTER: Nguyen VD
PROVIDER: S-EPMC5551826 | biostudies-other | 2017 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Heavy metals are toxic substances that pose a real danger to humans and organisms, even at low concentration. Therefore, there is an urgent need to remove heavy metals. Herein, the nanocellulose (NC) was synthesized by the hydrolysis of cellulose using sulfuric acid, and then functionalized using polypyrrole (ppy) through a polymerization reaction to produce polypyrrole/nanocellulose (ppy/NC) nanocomposite. The synthesized nanocomposite was characterized using familiar techniques including XRD, FT-IR, SEM, TEM, and TGA. The obtained results showed a well-constructed nanocomposite with excellent thermal stability in the nano-sized scale. The adsorption experiments showed that the ppy/NC nanocomposite was able to adsorb hexavalent chromium (Cr(VI)). The optimum pH for the removal of the heavy metal was pH 2. The interfering ions showed minor effect on the adsorption of Cr(VI) resulted from the competition between ions for the adsorption sites. The adsorption kinetics were studied using pseudo 1st order and pseudo 2nd order models indicating that the pseudo second order model showed the best fit to the experimental data, signifying that the adsorption process is controlled by the chemisorption mechanism. Additionally, the nanocomposite showed a maximum adsorption capacity of 560 mg/g according to Langmuir isotherm. The study of the removal mechanism showed that Cr(VI) ions were removed via the reduction of high toxic Cr(VI) to lower toxic Cr(III) and the electrostatic attraction between protonated ppy and Cr(VI). Interestingly, the ppy/NC nanocomposite was reused for Cr(VI) uptake up to six cycles showing excellent regeneration results. Subsequently, Cr(VI) ions can be effectively removed from aqueous solution using the synthesized nanocomposite as reusable and cost-effective adsorbent.
| S-EPMC8587301 | biostudies-literature
Project description:Abstract: The removal of Cr(VI) in wastewater plays an important role in human health and environment. In this work, polypyrrole/hollow mesoporous silica particle (PPy/HMSNs) adsorbents have been newly synthesized by in-situ polymerization, which prevent the aggregation of pyrrole in the process of polymerization and exhibit highly selective and powerful adsorption ability for Cr(VI). The adsorption process was in good agreement with the quasi-second-order kinetic model and the Langmuir isotherm model. And the maximum adsorption capacity of Cr(VI) was 322 mg/g at 25 °C. Moreover, the removal rate of Cr(VI) by PPy/HMSNs was ~100% in a number of binary systems, such as Cl-/Cr(VI), NO3-/Cr(VI), SO42-/Cr(VI), Zn2+/Cr(VI), Fe3+/Cr(VI), Sn4+/Cr(VI), and Cu2+/Cr(VI). Thus, the PPy/HMSNs adsorbents have great potential for the removal of Cr(VI) in wastewater.
| S-EPMC7221785 | biostudies-literature
Project description:In order to remove hexavalent chromium (Cr(vi)) efficiently and simplify the adsorbent preparation process, we employed a single step method to prepare a new biochar supported manganese sulfide material. The nanoscale MnS particles were highly soldered on the biochar support surface, and this adsorbent displayed the effective removal of Cr(vi) (98.15 mg L-1) via synergistic effect between adsorption and reduction/precipitation under weak acid conditions (pH = 5.0-6.0). The adsorption kinetic data were described well by the pseudo second-order kinetic model, suggesting that the reaction process was a chemisorption process. The adsorption isotherm data were described well by the Redlich-Peterson model, further suggesting that this reaction was a hybrid chemical reaction-sorption process. In addition, the Dubinin-Radushkevich isotherm model with 8.28, 8.57, and 12.91 kJ mol-1 adsorption energy also suggests that it was a chemisorption process. The simple and eco-friendly preparation process, low-cost, and the high removal efficiency could make it a promising material for the purification of Cr(vi)-contaminated wastewater.
| S-EPMC9072298 | biostudies-literature
Project description:The present study investigated the biosorption capacity of live and dead cells of a novel Bacillus strain for chromium. The optimum biosorption condition was evaluated in various analytical parameters, including initial concentration of chromium, pH, and contact time. The Langmuir isotherm model showed an enhanced fit to the equilibrium data. Live and dead biomasses followed the monolayer biosorption of the active surface sites. The maximum biosorption capacity was 20.35 mg/g at 25 °C, with pH 3 and contact time of 50 min. Strain 139SI was an excellent host to the hexavalent chromium. The biosorption kinetics of chromium in the dead and live cells of Bacillus salmalaya (B. salmalaya) 139SI followed the pseudo second-order mechanism. Scanning electron microscopy and fourier transform infrared indicated significant influence of the dead cells on the biosorption of chromium based on cell morphological changes. Approximately 92% and 70% desorption efficiencies were achieved using dead and live cells, respectively. These findings demonstrated the high sorption capacity of dead biomasses of B. salmalaya 139SI in the biosorption process. Thermodynamic evaluation (ΔG⁰, ΔH⁰, and ΔS⁰) indicated that the mechanism of Cr(VI) adsorption is endothermic; that is, chemisorption. Results indicated that chromium accumulation occurred in the cell wall of B. salmalaya 139SI rather than intracellular accumulation.
| S-EPMC4690921 | biostudies-literature
Project description:Fe-modified biochars have been widely used in removal of Cr(VI) from water due to the resulting modified surface functional groups and magnetization property. However, few studies have synthetically investigated modification methods and synthesis parameters on the improvement of the removal efficiency of Cr(VI) by Fe-modified biochars. Herein, 10 types of corn straw-based magnetic biochars were produced using pre-modification and post-modification methods with various modifier ratios, and the highest heating temperature (HHT). Cr(VI) removal results suggest that the removal efficiency of pre-modified biochars ranged from 50.7 to 98.6%, which was much higher than that of post-modified (6.6-21.6%) and unmodified biochars (0.4-7.6%). The effect of synthesis methods on Cr(VI) adsorption was in the following order: Fe-modification method > modifier ratio > HHT. The adsorption kinetics and isotherm results of three types of pre-modified biochars were well fitted with the pseudo-second-order model (R 2 > 0.99) and the Langmuir adsorption model (R 2 > 0.99), respectively, indicating the surface homogeneity of the pre-modified biochars and unilayer chemisorptions of Cr(VI). Characterization results show that iron oxides or zerovalent iron particles were successfully deposited onto the surface of biochars and magnetism was introduced. A good Pearson correlation (r = -0.9694) between the removal efficiency and pH value in modified biochar suggests that the lower pH value may offer more positive charges and promote electrostatic attraction. Therefore, the dominant mechanism for enhanced Cr(VI) adsorption on pre-modified biochar was electrostatic attraction, resulting from its distinguished acidity nature. Our findings provide new insights into the high-efficiency removal of Cr(VI) onto Fe-modified magnetic biochars and will benefit future design of more efficient magnetic biochars.
| S-EPMC7726960 | biostudies-literature
Project description:In this study, different types of magnetic biochar nanocomposites were synthesized using the co-precipitation method. Two biochar materials, namely, sewage sludge biochar and woodchips biochar, were prepared at two different temperatures, viz., 450 and 700 °C. These biochars were further modified with magnetic nanoparticles (Fe3O4). The modified biochar nanocomposites were characterized using field emission-scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), SQUID analysis, X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared spectroscopy (FTIR). The potential of prepared adsorbents was examined for the removal of hexavalent chromium (Cr(VI)) and Acid orange 7 (AO7) dye from water as a function of various parameters, namely, contact time, pH of solution, amount of adsorbents, and initial concentrations of adsorbates. Various kinetic and isotherm models were tested to discuss and interpret the adsorption mechanisms. The maximum adsorption capacities of modified biochars were found as 80.96 and 110.27 mg g-1 for Cr(VI) and AO7, respectively. Magnetic biochars showed high pollutant removal efficiency after 5 cycles of adsorption/desorption. The results of this study revealed that the prepared adsorbents can be successfully used for multiple cycles to remove Cr(VI) and AO7 from water. Graphical Abstract.
| S-EPMC7417418 | biostudies-literature
Project description:Cr (VI) is indispensable in industrial manufacturing, and its extensive use leads to severe heavy-metal pollution in the water environment around people, posing a great danger to physical health and living environment of multitudinous organisms. Expanded graphite (EG) is considered as a typical material for adsorption, while nanoscale zero-valent iron (nZVI) can be applied to degrade and sedimentate various organic or inorganic pollutants. In this study, a simultaneous collaboration of EG and nZVI is carried out, with the investigation on the influence of different test conditions for adsorption performances. These findings demonstrate that nZVI@EG manifests favourable adsorptive performance on the removal of hexavalent chromium efficiently. nZVI, acting as an electron donor, is supposed to reduce Cr (VI) to Cr (III), turning itself into iron oxide or hydroxide. The whole process is an exothermic reaction, accompanying chemical reduction and physical adsorption. And Cr (III) is fastened on the appearance by deposition of chromium hydroxide or ferrochromium complex precipitation, which greatly reduces the total chromium content in the aqueous solution. Herein, as a new composite adsorbent, nZVI@EG shows promising prospects of practical applications in water contamination and environmental remediation.
| S-EPMC8371360 | biostudies-literature
Project description:Palladium (Pd) nanoparticle catalysis has attracted increasing attention due to its efficient catalytic activity and its wide application in environmental protection and chemical synthesis. In this work, Pd nanoparticles (about 71 nm) were synthesized in aqueous solution by microwave-assisted thermal synthesis and immobilized in beech wood blocks as Pd@wood catalysts. The wood blocks were first hydrothermally treated with 10% NaOH solution to improve the internal structure and increase their porosity, thereby providing favorable attachment sites for the formed Pd nanoparticles. The stable deposition of Pd nanoparticle clusters on the internal channels of the wood blocks can be clearly observed. In addition, the catalytic performance of the prepared Pd@wood was investigated through two model reactions: the reduction of 4-nitrophenol and Cr(VI). The Pd@wood catalyst showed 95.4 g-1 s-1 M-1 of normalized rate constant knorm and 2.03 min-1 of the TOF, respectively. Furthermore, Pd nanoparticles are integrated into the internal structure of wood blocks by microwave-assisted thermal synthesis, which is an effective method for wood functionalization. It benefits metal nanoparticle catalysis in the synthesis of fine chemicals as well as in industrial wastewater treatment.
| S-EPMC10490320 | biostudies-literature
Project description:Chromium (Cr(VI)) pollution has attracted wide attention due to its high toxicity and carcinogenicity. Modified biochar has been widely used in the removal of Cr(VI) in water as an efficient and green adsorbent. However, the existing biochar prepared by chemical modification is usually complicated in process, high in cost, and has secondary pollution, which limits its application. It is urgent to explore modified biochar with simple process, low cost and environmental friendliness. Therefore, ball milling wheat straw biochar (BM-WB) was prepared by ball milling technology in this paper. The adsorption characteristics and mechanism of Cr(VI) removal by BM-WB were analyzed by functional group characterization, adsorption model and response surface method. The results showed that ball milling effectively reduced the particle size of biochar, increased the specific surface area, and more importantly, enhanced the content of oxygen-containing functional groups on the surface of biochar. After ball milling, the adsorption capacity of Cr(VI) increased by 3.5-9.1 times, and the adsorption capacity reached 52.21 mg/g. The adsorption behavior of Cr(VI) follows the pseudo-second-order kinetics and Langmuir isotherm adsorption model rate. Moreover, the Cr(VI) adsorption process of BM-WB is endothermic and spontaneous. Under the optimized conditions of pH 2, temperature 45 °C, and adsorbent dosage 0.1 g, the removal rate of Cr(VI) in the solution can reach 100%. The mechanism of Cr(VI) adsorption by BM-WB is mainly based on electrostatic attraction, redox and complexation. Therefore, ball milled biochar is a cheap, simple and efficient Cr(VI) removal material, which has a good application prospect in the field of remediation of Cr(VI) pollution in water.
| S-EPMC10901879 | biostudies-literature
Project description:We prepared a novel adsorbent functionalized by bagasse magnetic biochar (BMBC). To study the removal behaviors and mechanisms of Cr(VI) by BMBC, batch adsorption experiments were conducted by modifying variables, such as pH, adsorption time, BMBC dosages, initial Cr concentration, co-existing ions, and ionic strength, and characterizing BMBC before and after Cr(VI) adsorption. BMBC was primarily composed of Fe2O3 and Fe3O4 on bagasse boichar with an amorphous structure. The specific surface area of BMBC was 81.94 m2 g-1, and the pHpzc of BMBC was 6.2. The fabricated BMBC showed high adsorption performance of Cr(VI) in aqueous solution. The maximum Cr(VI) adsorption capacity of BMBC was 29.08 mg g-1 at 25 ºC, which was much higher than that of conventional biochar sorbents. The adsorption process followed pseudo-second-order kinetics and could be explained by the involvement of the Langmuir isotherm in monolayer adsorption. The crystalline structure of Fe3O4 in the BMBC changed slightly during the adsorption process; Fe3O4 improved the adsorption of Cr(VI) on BMB. The desorption capacity of Cr(VI) was 8.21 mg g-1 when 0.2 mol L-1 NaOH was used as the desorption solution. After being reused three times, the removal efficiency is still as high as 80.36%.
| S-EPMC7722720 | biostudies-literature