Study of Al-Si Alloy Oxygen Saturation on Its Microstructure and Mechanical Properties.
Ontology highlight
ABSTRACT:
SUBMITTER: Finkelstein A
PROVIDER: S-EPMC5551829 | biostudies-other | 2017 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Al-5Ti-C master alloy was prepared and used to modify hypereutectic Al-20%Si alloy. The microstructure evolution and mechanical properties of hypereutectic Al-20%Si alloy with Al-5Ti-C master alloy additions (0, 0.4, 0.6, 1.0, 1.6 and 2.0 wt%) were investigated. The results show that, Al-5Ti-C master alloy (0.6 wt%, 10 min) can significantly refine both eutectic and primary Si of hypereutectic Al-20%Si alloy. The morphology of the primary Si crystals was significantly refined from a coarse polygonal and star-like shape to a fine polyhedral shape and the grain size of the primary Si was refined from roughly 90-120 μm to 20-50 μm. The eutectic Si phases were modified from a coarse platelet-like/needle-like structure to a fine fibrous structure with discrete particles. The Al-5Ti-C master alloy (0.6 wt%, 30 min) still has a good refinement effect. The ultimate tensile strength (UTS), elongation (El) and Brinell hardness (HB) of Al-20%Si alloy modified by the Al-5Ti-C master alloy (0.6 wt%, 10 min) increased by roughly 65%, 70% and 51%, respectively, due to decreasing the size and changing the morphology on the primary and eutectic Si crystals. The change in mechanical properties corresponds to evolution of the microstructure.
| S-EPMC5453074 | biostudies-other
Project description:It is found that Li₂Sb compound can act as the nucleus of primary Mg₂Si during solidification, by which the particle size of primary Mg₂Si decreased from ~300 to ~15-25 μm. Owing to the synergistic effect of the Li₂Sb nucleus and adsorption-poisoning of Li atoms, the effect of complex modification of Li-Sb on primary Mg₂Si was better than that of single modification of Li or Sb. When Li-Sb content increased from 0 to 0.2 and further to 0.5 wt.%, coarse dendrite changed to defective truncated octahedron and finally to perfect truncated octahedral shape. With the addition of Li and Sb, ultimate compression strength (UCS) of Al-20Mg₂Si alloys increased from ~283 to ~341 MPa and the yield strength (YS) at 0.2% offset increased from ~112 to ~179 MPa while almost no change was seen in the uniform elongation. Our study offers a simple method to control the morphology and size of primary Mg₂Si, which will inspire developing new Al-Mg-Si alloys with improved mechanical properties.
| S-EPMC5502895 | biostudies-other
Project description:Metallic glass-reinforced metal matrix composites are an emerging class of composite materials. The metallic nature and the high mechanical strength of the reinforcing phase offers unique possibilities for improving the engineering performance of composites. Understanding the structure at the amorphous/crystalline interfaces and the deformation behavior of these composites is of vital importance for their further development and potential application. In the present work, Zr-based metallic glass fibers have been introduced in Al7075 alloy (Al-Zn-Mg-Cu) matrices using spark plasma sintering (SPS) producing composites with low porosity. The addition of metallic glass reinforcements in the Al-based matrix significantly improves the mechanical behavior of the composites in compression. High-resolution TEM observations at the interface reveal the formation of a thin interdiffusion layer able to provide good bonding between the reinforcing phase and the Al-based matrix. The deformation behavior of the composites was studied, indicating that local plastic deformation occurred in the matrix near the glassy reinforcements followed by the initiation and propagation of cracks mainly through the matrix. The reinforcing phase is seen to inhibit the plastic deformation and retard the crack propagation. The findings offer new insights into the mechanical behavior of metal matrix composites reinforced with metallic glasses.
| S-EPMC4828712 | biostudies-literature
Project description:High-strength aluminum alloy (mainly refers to the 7xxx series) is the optimum material for lightweight military equipment. However, this type of aluminum alloy is a wrought aluminum alloy. If it is directly formed by traditional casting methods, there will inevitably be problems such as coarseness, unevenness, looseness, and hot cracking in the structure, which will greatly affect the final performance of the part. Based on the internal cooling with annular electromagnetic stirring (IC-AEMS) method, a new technology of rheological die forging is developed in this paper, and the scale-reduced parts of a brake hub of Al-6.54Zn-2.40Cu-2.35Mg-0.10Zr aluminum alloy were prepared. The influence of IC-AEMS and the addition of rare element Sc on the structure and mechanical properties of the parts was studied. An optical microscope and scanning electron microscope (SEM) were used to observe the microstructure evolution, energy dispersive spectroscopy (EDS) was used to analyze the phase distribution and composition, and the mechanical properties of the parts were tested by uniaxial tensile tests. The results show that the addition of Sc element can effectively refine the grains and improve the strength and elongation of the material; the application of IC-AEMS improves the cooling rate of the melt, increases the effective nucleation rate, and the grains are further refined. Through process optimization, scale-reduced parts of a brake hub with good formability and mechanical properties can be obtained, the ultimate tensile strength is 597.2 ± 3.1 MPa, the yield strength is 517.8 ± 4.3 MPa, and the elongation is 13.7 ± 1.3%.
| S-EPMC7762574 | biostudies-literature
Project description:The dataset presented here shows the microstructure and mechanical properties of secondary (recycled) cast aluminum-silicon (Al-Si) piston alloys processed through severe plastic deformation technique, known as high-pressure torsion (HPT). The HPT processing was undertaken for 1/4, 1/2, 1 and 10 turns of the lower anvil (rotating at constant speed of 1rpm) while the upper anvil maintained at a normal pressure of 3.0 GPa. The data on microstructural evolution obtained at the central region and edge of the circular (disk) HPT sample were obtained using optical and scanning electron microscopy and these data are presented here. The data on the analysis of the particle shape, sizes and distribution from the micrographs using ImageJ software are also presented. Data on mechanical properties characterized using Vickers microhardness measurement across the surface of HPT sample are also shown. Pictures depicting the microhardness measurement scheme, high-pressure torsion facility and sample nomenclature are presented.
| S-EPMC6700338 | biostudies-literature
Project description:One of the major aims of the modern materials foundry industry is the achievement of advanced mechanical properties of metals, especially of light non-ferrous alloys such as aluminum. Usually an alloying process is applied to obtain the required properties of aluminum alloys. However, the presented work describes an alternative approach through the application of vibration treatment, modification by ultrafine powder and a combination of these two methods. Microstructural studies followed by image analysis revealed the refinement of α-Al grains with an increase in the Si network area around them. As evidence, the improvement of the mechanical properties of Al casting alloy was detected. It was found that the alloys subjected to the vibration treatment displayed an increase in tensile and yield strengths by 20% and 10%, respectively.
| S-EPMC5459002 | biostudies-other
Project description:Optically transparent, colorless Al-O-N and Al-Si-O-N coatings with discretely varied O and Si contents were fabricated by reactive direct current magnetron sputtering (R-DCMS) from elemental Al and Si targets and O2 and N2 reactive gases. The Si/Al content was adjusted through the electrical power on the Si and Al targets, while the O/N content was controlled through the O2 flow piped to the substrate in addition to the N2 flow at the targets. The structure and morphology of the coatings were studied by X-ray diffraction (XRD) and transmission electron microscopy (TEM), while the elemental composition was obtained from Rutherford backscattering spectrometry (RBS) and heavy ion elastic recoil detection analysis (ERDA). The chemical states of the elements in the coatings were analyzed by X-ray photoelectron spectroscopy (XPS). Based on analytical results, a model describing the microstructural evolution of the Al-O-N and also previously studied Al-Si-N [1, 2, 3, 4] coatings with O and Si content, respectively, is established. The universality of the microstructural evolution of these coatings with the concentration of the added element is attributed to the extra valence electron (e-) that must be incorporated into the AlN wurtzite host lattice. In the case of Al-O-N, this additional valence charge arises from the e - acceptor O replacing N in the AlN wurtzite lattice, while the e - donor Si substituting Al fulfills that role in the Al-Si-N system. In view of future applications of ternary Al-O-N and quaternary Al-Si-O-N transparent protective coatings, their mechanical properties such as residual stress (?), hardness (HD) and Young's modulus (E) were obtained from the curvature of films deposited onto thin substrates and by nanoindentation, respectively. Moderate compressive stress levels between -0.2 and -0.5 GPa, which suppress crack formation and film-substrate delamination, could be obtained together with HD values around 25 GPa.
| S-EPMC6844387 | biostudies-literature
Project description:Herein, the effects of height-diameter ratios (H/D) on the microstructure evolution and mechanical properties of 0.4C-Si-Mn-Cr steel during high temperature deformation are reported. The compression experiments were performed on steel samples using Gleeble to obtain a reasonable deformation temperature, and the degree of deformation was assessed in the range of 1.5 to 2.0 H/D via forging. The forged specimens were quenched using the same heat treatment process. The hardness and impact toughness of the steel samples were tested before and after heat treatment. Grain sizes gradually increased with an increase in the compression temperature from 950 °C to 1150 °C, and the grain sizes decreased with an increase in H/D. The microstructure of the steel samples contained pearlite, bainite, martensite, and retained austenite phase. The microstructure after forging was more uniform and finer as compared to that of as-cast steel samples. The hardness and impact toughness of the steel samples were evaluated after forging; hardness first increased and then decreased with an increase in H/D, while the impact toughness continuously increased with an increase in H/D. Hence, the microstructure and properties of steel could be improved via high temperature deformation, and this was primarily related to grain refinement.
| S-EPMC6981509 | biostudies-literature
Project description:The dynamic metallurgical characteristics of the selective laser melting (SLM) process offer fabricated materials with non-equilibrium microstructures compared to their cast and wrought counterparts. To date, few studies on the precipitation kinetics of SLM processed heat-treatable alloys have been reported, despite the importance of obtaining such detailed knowledge for optimizing the mechanical properties. In this study, for the first time, the precipitation behavior of an SLM fabricated Al-Mn-Sc alloy was systematically investigated over the temperature range of 300-450 °C. The combination of in-situ synchrotron-based ultra-small angle X-ray scattering (USAXS), small angle X-ray scattering (SAXS) and X-ray diffraction (XRD) revealed the continuous evolution of Al6Mn and Al3Sc precipitates upon isothermal heating in both precipitate structure and morphology, which was confirmed by ex-situ transmission electron microscopy (TEM) studies. A pseudo-delay nucleation and growth phenomenon of the Al3Sc precipitates was observed for the SLM fabricated Al-Mn-Sc alloy. This phenomenon was attributed to the preformed Sc clusters in the as-fabricated condition due to the intrinsic heat treatment effect induced by the unique layer-by-layer building nature of SLM. The growth kinetics for the Al6Mn and Al3Sc precipitates were established based on the in-situ X-ray studies, with the respective activation energies determined to be (74 ± 4) kJ/mol and (63 ± 9) kJ/mol. The role of the precipitate evolution on the final mechanical properties was evaluated by tensile testing, and an observed discontinuous yielding phenomenon was effectively alleviated with increased aging temperatures.
| S-EPMC7574377 | biostudies-literature
Project description:Atomic scale characterization of fine precipitates in an under-aged Cu added Al-Mg-Si alloy was carried out by combination of atomically-resolved annular dark-field scanning transmission electron microscopy and energy dispersive X-ray spectroscopy. Two types of precipitates were observed in the alloy. In the case of ordered ?" precipitates, ?" was proposed as Mg5-xAl2+xSi4 (x ? 1) with solute Cu atoms replacing Al site of ?" precipitate. In the case of disordered precipitates, the precipitates were found to consist of ?" sub-unit cells, three-fold symmetric structure without Cu atoms, Cu containing structures termed as "Cu sub-unit cluster", and Q' sub-unit cells. Among these structures, the morphologies of three-fold symmetric structure without Cu atoms, Cu sub-unit cluster, and Q' sub-unit cell were almost the same, so that these structures should be the clusters of Q' phase. Since the areal density, length and diameter of precipitates were almost equal between Cu free Al-Mg-Si alloy and Cu added Al-Mg-Si alloy, the increase of hardness by Cu addition should be due to the precipitation of Cu related precipitates, such as Cu sub-unit clusters and Q' sub-unit cells.
| S-EPMC6226491 | biostudies-literature