Characterisation of Asphalt Concrete Using Nanoindentation.
Ontology highlight
ABSTRACT:
SUBMITTER: Barbhuiya S
PROVIDER: S-EPMC5551866 | biostudies-other | 2017 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description: Not available
| S-EPMC10655589 | biostudies-literature
Project description:After a biological terrorist attack, understanding the migration of agents such as Bacillus anthracis is critical due to their deadly nature. This is important in urban settings with higher likelihood of human exposure and a large fraction of impervious materials contributing to pollutant washoff. The study goals were to understand the removal of spores from urban surfaces under different rainfall conditions, to compare washoff of two B. anthracis surrogate spores, and to compare two empirical fits for the first flush of spores from small areas. Concrete and asphalt were inoculated with either Bacillus atrophaeus or Bacillus thuringiensis kurstaki spores and exposed to simulated rainfall. The study assessed goodness-of-fit for the Storm Water Management Model (SWMM)'s exponential washoff function compared to an alternative two-stage exponential function. The highest average washoff of spores was 15% for an hour-long experiment. Spore washoff was not significantly different for the two spore types, but there were significant differences in washoff from asphalt versus concrete with more occurring from asphalt. Average kinetic energy of the storm event impacted washoff from asphalt, but not concrete. The two-stage function had a better goodness-of-fit than the SWMM exponential function. As such, emergency responders should be aware that the spread of contamination is impacted by the droplet characteristics of the storm event and the surface material type in the contaminated area; modelers should be aware that different data-fitting approaches may be more appropriate for first-flush calculations of small washoff areas than those used for continuous long-term simulation of large subcatchments.
| S-EPMC8959000 | biostudies-literature
Project description:In line with the current trend of seeking alternative methods for modification of the existing building composites, such as mineral-asphalt mixtures (MAMs), the materials from concrete and ceramics recycling are being used in increasingly wider applications. When added to MAMs as an aggregate, ceramic building material, which has different properties than the raw material (clay), may significantly influence the aggregate properties, including the wettability, porosity, asphalt adhesion, and consequently the mixture durability. The material's microstructure was found using SEM. The wetting properties of mineral-asphalt mixtures were determined by measuring the contact angles (CA) of their surfaces, using water as the measuring liquid. The total surface free energy (SFE) values were determined using the Neumann method. When analyzing the research results, it can be noticed that the chemical composition of the ceramic aggregate has a significant influence on the adhesion of asphalt to its surface due to the chemical affinity. Waste ceramic aggregate, despite its acidic pH value being connected with its elevated silica content, exhibits good adhesive properties.
| S-EPMC7504282 | biostudies-literature
Project description:The deterioration of road conditions and increasing repair deficits pose challenges for the maintenance of reliable road infrastructure, and thus threaten, for example, safety and the fluent flow of traffic. Improved and more efficient procedures for maintenance are required, and these require improved knowledge of road conditions, i.e., improved data. Three-dimensional mapping presents possibilities for large-scale collection of data on road surfaces and automatic evaluation of maintenance needs. However, the development and, specifically, evaluation of large-scale mobile methods requires reliable references. To evaluate possibilities for close-range, static, high-resolution, three-dimensional measurement of road surfaces for reference use, three measurement methods and five instrumentations are investigated: terrestrial laser scanning (TLS, Leica RTC360), photogrammetry using high-resolution professional-grade cameras (Nikon D800 and D810E), photogrammetry using an industrial camera (FLIR Grasshopper GS3-U3-120S6C-C), and structured-light handheld scanners Artec Leo and Faro Freestyle. High-resolution photogrammetry is established as reference based on laboratory measurements and point density. The instrumentations are compared against one another using cross-sections, point-point distances, and ability to obtain key metrics of defects, and a qualitative assessment of the processing procedures for each is carried out. It is found that photogrammetric models provide the highest resolutions (10-50 million points per m2) and photogrammetric and TLS approaches perform robustly in precision with consistent sub-millimeter offsets relative to one another, while handheld scanners perform relatively inconsistently. A discussion on the practical implications of using each of the examined instrumentations is presented.
| S-EPMC8708010 | biostudies-literature
Project description:Despite widespread agreement on the beneficial nature of hydrated lime (HL) addition to asphalt concrete mixes, understanding of the effect of HL particle size is still limited. Previous investigations have focused mainly on two different size comparisons, and so certain guidance for a practical application cannot yet be produced. This study investigates three distinct sizes of HL, in the range of regular, nano, and sub-nano scales, for their effects on the properties of modified asphalt concretes. Five different percentages of HL as a partial replacement of ordinary limestone filler in asphalt concrete mixes were studied for wearing course application purposes. Experimental tests were conducted to evaluate the mechanical properties, including resistance to plastic flow, volumetric properties, moisture susceptibility, resilient modulus, and permanent deformation. The results revealed that a positive correlation exists between the mechanical properties and the fineness of HL particle sizes.
| S-EPMC9146764 | biostudies-literature
Project description:High-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research presented in this paper. Four test sections with HMAC used in base and binder courses were evaluated in the study. Field investigations of the number of low-temperature cracks were performed over several years. It was established that the number of new low-temperature cracks is susceptible to many random factors, and the statistical term "reversion to the mean" should be considered. A new factor named Increase in Cracking Index was developed to analyze the resistance of pavement to low-temperature cracking. For all the considered field sections, samples were cut from each asphalt layer, and Thermal Stress Restrained Specimen Tests were performed in the laboratory. Correlations of temperature at failure and cryogenic stresses with the cracking intensity observed in the field were analyzed. The paper provides practical suggestions for pavement designers. When the use of high modulus asphalt concrete is planned for binder course and asphalt base, which may result in lower resistance to low-temperature cracking of pavement than in the case of conventional asphalt concrete, it is advisable to apply a wearing course with improved resistance to low-temperature cracking. Such an approach may compensate for the adverse effects of usage of high modulus asphalt concrete.
| S-EPMC8746051 | biostudies-literature
Project description:AC (asphalt concrete)-13, as the main material used in pavement construction, has been applied widely in seasonal frozen areas. In order to understand the fracture mechanism in the freeze-thaw (F-T) damage process, the mesoscale structure of AC-13 is obtained by computed tomography (CT). The fractal dimension of cracks is used as a damage evaluation index. Most previous studies have only focused on the fractal dimensions of whole cracks, while ignoring the fractal tectonic process and the self-similarity degree of a single fracture. Therefore, in this study, the intrinsic mechanism of fractures and damage were investigated. In addition, the critical crack stress and fracture toughness models of a single fracture in a freeze-thaw damage process are established for AC-13. The results indicate that in terms of the critical crack stress and fracture toughness, with the increase of F-T times, there is an obvious decreasing trend. The fracture model can effectively describe the fracture toughness calculated by ABAQUS in the process of freeze-thaw cycles.
| S-EPMC6678352 | biostudies-literature
Project description:Road distress results in high maintenance costs. However, increased understandings of asphalt behaviour and properties coupled with technological developments have allowed paving technologists to examine the benefits of introducing additives and modifiers. As a result, polymers have become extremely popular as modifiers to improve the performance of the asphalt mix. This study investigates the performance characteristics of epoxidized natural rubber (ENR)-modified hot-mix asphalt. Tests were conducted using ENR-asphalt mixes prepared using the wet process. Mechanical testing on the ENR-asphalt mixes showed that the resilient modulus of the mixes was greatly affected by testing temperature and frequency. On the other hand, although rutting performance decreased at high temperatures because of the increased elasticity of the ENR-asphalt mixes, fatigue performance improved at intermediate temperatures as compared to the base mix. However, durability tests indicated that the ENR-asphalt mixes were slightly susceptible to the presence of moisture. In conclusion, the performance of asphalt pavement can be enhanced by incorporating ENR as a modifier to counter major road distress.
| S-EPMC5300135 | biostudies-literature
Project description:The aim of this study is to assess the viscoelastic parameters (i.e., phase angle and dynamic modulus) of asphalt concrete-wearing course (AC-WC) and hot rolled sheet-wearing course (HRS-WC) mixtures obtained from the dynamic modulus test. This study was accomplished in four stages: determining optimum asphalt content using Marshall mix design procedure, stability and flow parameters from Marshall test, viscoelastic parameters from dynamic modulus testing and finally the generation of dynamic modulus master curves at a reference temperature of 25 °C. The results showed that at the same temperature, the dynamic modulus of AC-WC and HRS-WC mixtures tended to increase with escalating the loading frequency, while dynamic modulus decreases with an increase in the test temperature at constant loading frequency. Furthermore, the dynamic modulus of the AC-WC mixture was recorded as 100% higher than the HRS-WC asphalt mixture. The phase angle, however, showed contradictory behavior with that shown in dynamic modulus. The phase angle of the AC-WC mixture and HRS-WC asphalt mixture showed almost the same behavior. Similarly, the dynamic modulus master curves of AC-WC and HRS-WC asphalt mixtures can be used to predict the dynamic modulus at the frequency range of 0.01 to 10 Hz and a reference temperature of 25 °C. The results were also used to evaluate the rutting and fatigue performance of AC-WC and HRS-WC.
| S-EPMC7084968 | biostudies-literature
Project description:Reclaimed asphalt pavement (RAP) is a valuable commodity originating during processes of road/highways rehabilitations, resurfacing in the cases of the revelation of underneath-placed layers. Removed material can be successfully recycled and utilized as a supplementing material for new hot asphalt mixes. However, its dosages are limited because of variations in properties of aged bitumen compared to fresh material and, thus, a significant amount of waste material is remaining as waste products. Nonetheless, this commodity may find usage in the construction industry that suffers from a shortage of high-quality and easily available aggregates. This work aimed to investigate the optimal substitution of mined natural aggregate with commonly available RAP in order to produce composites with the comparable mechanical performance of reference ordinary Portland concrete. The aggregate substitutions up to 100% with RAP have been studied with a combination of mechanical and analytical techniques. Obtained experimental data showed changes in the porous structure, mineralogy, and in the amount of formed cement-related hydration products that influenced the mechanical performance of produced composites. Composite with 10% of natural aggregate substitution with RAP has shown the strength class C16/20 after 28 days of water curing, according to the EN 206-1. Such innovative products could be utilized in the construction industry. The usage of waste RAP could contribute to preservation of our environment for future generations.
| S-EPMC7663929 | biostudies-literature