Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Preparation of Superhydrophobic Film on Ti Substrate and Its Anticorrosion Property.

ABSTRACT: Superhydrophobic films were fabricated on a titanium substrate with or without anodizing by using a self-assembling method. Firstly, the pretreatments of mechanical polishing/anodizing or mechanical polishing only were conducted, respectively. Subsequently, the preparation of polydopamine film layer, deposition of nano-silver particles, and post modification of 1H,1H,2H,2H-perfluorodecanethiol were performed on the surface of the pretreated substrate. The surface morphologies, compositions, wettability, and corrosion resistance of the films were investigated with scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS), water contact angle measurements, and electrochemical tests, respectively. Meanwhile, the effect of the deposition time in the silver nitrate solution on the hydrophobicity of the specimen surface was investigated. The result showed that with the increase of deposition time, the hydrophobic property enhanced gradually. The surface deposited for 7 h exhibited an optimum hydrophobic effect, which was characterized with a large water contact angle (WCA) of 154°, and the surface was rather rough and covered by a relatively uniform layer of micro-nano silver particles. The excellent hydrophobicity was attributed to a rough stratified microstructure along with the low surface energy. The electrochemical measurements showed that the existence of the superhydrophobic film can effectively enhance the corrosion resistance of Ti samples.

SUBMITTER: Zhu M

PROVIDER: S-EPMC5553536 | biostudies-other | 2017 Jun

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

A Simple Laser Ablation-Assisted Method for Fabrication of Superhydrophobic SERS Substrate on Teflon Film.

Project description:With high sensitivity at single molecule level, surface-enhanced Raman scattering (SERS) is considered as an ultrasensitive optical detection technology with broad application prospects in lots of fields. However, the complicated fabrication and unaffordable price of SERS substrate are still a roadblock on the way to be widely used in industry. In this work, the SERS spectra on a commercial laser engraved Teflon (PTFE) film with engraved microarray are investigated. The wettability of film surface modulated by laser engraving make the microarray have the ability to decrease the contact area on film surface while water evaporation. The SEM image of the engraved area points out the micro/nanostructures generated engraving process is crucial to its superhydrophobic property. The probing molecules (i.e., methylene blue and rhodamine6G) were utilized to investigate with the limit of detection (1 × 10-14 M). Furthermore, the biomolecule (bovine serum albumin) was used to demonstrate its benefits in biological applications. The measured intensities of Raman spectra on this PTFE with laser engraved microarray demonstrate its potential value for a SERS substrate. Our work on this simple, cheap SERS substrate with high sensitivity has a great commercial value and plenty of application in lots of fields.

| S-EPMC6104470 | biostudies-literature

Noble Metal Nanoparticles in Pectin Matrix. Preparation, Film Formation, Property Analysis, and Application in Electrocatalysis.

Project description:Stable polymeric materials with embedded nano-objects, retaining their specific properties, are indispensable for the development of nanotechnology. Here, a method to obtain Pt, Pd, Au, and Ag nanoparticles (ca. 10 nm, independent of the metal) by the reduction of their ions in pectin, in the absence of additional reducing agents, is described. Specific interactions between the pectin functional groups and nanoparticles were detected, and they depend on the metal. Bundles and protruding nanoparticles are present on the surface of nanoparticles/pectin films. These films, deposited on the electrode surface, exhibit electrochemical response, characteristic for a given metal. Their electrocatalytic activity toward the oxidation of a few exemplary organic molecules was demonstrated. In particular, a synergetic effect of simultaneously prepared Au and Pt nanoparticles in pectin films on glucose electro-oxidation was found.

| S-EPMC7513339 | biostudies-literature

The Preparation of TiO? Film by the Sol-Gel Method and Evaluation of Its Self-Cleaning Property.

Project description:TiO? sol was produced by the sol-gel method through the hydrolysis and the aging of tetrabutyl titanate and the TiO? film was obtained by dipping and uniform lifting of the acid-treated and ultrasound-treated clean glass slides into the TiO? sol followed by aging, drying, and calcination. The effect of the hydrolysis control agents to the formed sol was researched and the crystalline state, the morphology, and the photocatalytic properties of the products after calcination were characterized. The structural morphology, the contact angles before and after illumination, and the self-cleaning properties of the TiO? film were characterized as well. The results showed that by using acetylacetone as the hydrolysis control agent, the formed TiO? sol had relatively high stability. The product after the calcination of the TiO? sol was of single anatase type with crystalline size of 18-20 nm and it could degrade nearly 100% of methylene blue after 90 min illumination. The formed TiO? film is compact, continuous, smooth, and had the properties of super-hydrophilicity (after 30 min illumination due to its contact angle decreasing from 21° to nearly 0°) and anti-fogging capability, which indicated its excellent self-cleaning property.

| S-EPMC5873029 | biostudies-literature

Transcriptome analysis of rMSCs cultured for 4 hours in differerent substrate (TCP, PCL film, ISB-P fIlm)

Project description:We developed new isosorbide derivatives (propoxylated or ethoxylated isosorbide) which have more reactivity in PCL-PU copolymer synthesis than the original isosorbide. PCL-PU copolymer incorporated propoxylated isosorbide (ISB-P) exhibited notable mechanical performance (50 MPa tensile strength and 1150% elongation with hyperelasticity under cyclic load), ultra-cell-adhesive property, and enhanced osteogenic differentiation. There was no significant difference in surface characteristics between ISB-P and PCL), however, mRNA profiles showed higher expressions of heat shock proteins which have been reported to promote osteogenic differentiation at 4 h after cell seeding in rMSC cultured on ISB-P compared to PCL. In conclusion, the engagement of heat shock protein to the ISB-P surface during cell attachment may promote osteogenic differentiation in ISB-P.

2022-04-01 | GSE199790 | GEO

Preparation of nanoporous BiVO<sub>4</sub>/TiO<sub>2</sub>/Ti film through electrodeposition for photoelectrochemical water splitting.

Project description:A nanoporous BiVO4/TiO2/Ti film was successfully fabricated by electrodepositing a nanoporous BiOI film on nanoporous TiO2 arrays followed by annealing at 450°C for 2 h. The electrodeposition of BiOI film was carried out at different times (10, 30, 100, 500 and 1000 s) in Bi(NO3)3 and KI solution. The morphological, crystallographic and photoelectrochemical properties of the prepared BiVO4/TiO2/Ti heterojunction film were examined by using different characterization techniques. UV-vis spectrum absorption studies confirmed an increase in absorption intensities with increasing electrodeposition time, and the band gap of BiVO4/TiO2/Ti film is lower than that of TiO2/Ti. The photocatalytic efficiency of BiVO4/TiO2/Ti heterojunction film was higher compared to that of the TiO2/Ti film owing to the longer transient decay time for BiVO4/TiO2/Ti film (3.2 s) than that of TiO2/Ti film (0.95 s) in our experiment. The BiVO4/TiO2/Ti heterojunction film prepared by electrodeposition for 1000 s followed by annealing showed a high photocurrent density of 0.3363 mA cm-2 at 0.6 V versus saturated calomel electrode. Furthermore, the lowest charge transfer resistance from electrochemical impedance spectroscopy was recorded for the BiVO4/TiO2/Ti film (1000 s) under irradiation.

| S-EPMC6170590 | biostudies-literature

Preparation of a novel zwitterionic striped surface thin-film composite nanofiltration membrane with excellent salt separation performance and antifouling property.

Project description:Thin-film composite (TFC) nanofiltration (NF) membranes were fabricated via the co-deposition of taurine, tannic acid (TA), and polyethyleneimine (PEI), followed by subsequent interfacial polymerization with trimesoyl chloride (TMC) on the surface of the polysulfone ultrafiltration substrates. The surface properties, including the roughness, hydrophilicity, surface potential, and NF performances were facilely tuned by varying the taurine content for the prepared TFC membranes. In addition, the as-prepared TFC NF membranes had an excellent antifouling property and flux recovery ratio (FRR) in humic acid (HA), bovine serum albumin (BSA) and sodium alginate (SA) filtration tests. These results also revealed that the taurine content controlled the formation of the striped surface. Thus, this work provided a viable strategy for fabricating TFC NF membranes with high selectivity and outstanding antifouling ability.

| S-EPMC9052886 | biostudies-literature

Preparation of the Temperature-Responsive Superhydrophobic Paper with High Stability.

Project description:In this paper, a method for preparing a high-stability superhydrophobic paper with temperature-induced wettability transition is proposed. First, a temperature-responsive superhydrophobic triblock polymer PHFMA-PTSPM-PNIPAAm was prepared by one-step polymerization of TSPM, HFMA, and NIPAAm in a mass ratio of 0.3:0.3:0.3, then a superhydrophobic paper with a good temperature response was successfully prepared by grafting amino-modified SiO2 with the polymer to modify the surface of the paper. A further study found that when the mass ratio of amino-modified SiO2 to polymer is 0.2, the coating has good superhydrophobicity and transparency. What is more, the prepared modified paper is in a superhydrophobic state when the temperature is higher than 32 °C, and is in a superhydrophilic state when it is lower than 32 °C, which can realize free conversion between superhydrophobic and superhydrophilic states. In addition, the superhydrophobic paper prepared by this method not only has high oil-water separation efficiency, and the superhydrophobic coating shows good stability and transparency, but also has low requirements of environmental conditions for preparation, relatively simple preparation process, and strong repeatability, and it has a very broad application prospect.

| S-EPMC8223434 | biostudies-literature

Gravure printing for mesoporous film preparation.

Project description:This study presents gravure printing as a new strategy for rapid printing of ceramic mesoporous films and highlights its advantages over conventional mesoporous film preparation using evaporation induced self-assembly together with dip-coating. By varying the printing process parameters, the mesoporous coating thicknesses can be adjusted between 20 and 200 nm while maintaining a very high film homogeneity allowing the printing of ultrathin mesoporous films. Step gradients in film composition are accessible by consecutively printing two different "inks". Thereby, gravure printing is a much faster process than mesoporous single- and multilayer preparation using conventional dip-coating because lower amounts of solution are transferred and dissolution of previously deposited layers is avoided. The effect of printing process parameters on resulting film characteristics as well as the resulting mesoporous film's ionic accessibility is systematically investigated.

| S-EPMC9069313 | biostudies-literature

Design of Superhydrophobic Shape Memory Composites with Kirigami Structures and Uniform Wetting Property.

Project description:With the continuous increase in human demand to improve aircraft performance, intelligent aircraft technologies have become a popular research field in recent years. Among them, the deformable skin structure has become one of the key technologies to achieve excellent and reliable performance. However, during the service, deformable skin structures may encounter problems such as surface impact and adhesion of droplets in rainy weather or surface icing in low-temperature environments, which can seriously affect the flight safety of the aircraft. One way to overcome these issues is to use superhydrophobic shape memory materials in the structure. In this regard, first, shape memory composites were prepared with shape memory epoxy resin as the matrix and carbon fiber orthogonal woven fabric as the reinforcement material. Superhydrophobic shape memory composites (SSMCs) were then obtained by casting the kirigami composite with superhydrophobic carbon nanotube-polydimethylsiloxane (CNT@PDMS) mixture, and the surface was processed by laser micromachining. Shape memory performance and surface wetting performance were determined by material testing methods. The results showed that the shape memory recovery rate can reach 85.11%, the surface is superhydrophobic, the average water contact angle is 156.9 ± 4.4°, and the average rolling angle is 3 ± 0.5°. The three-point bending test of the specimens with different kirigami cell configurations showed that the shape memory composite based on the rectangular structure has the best deformability with an aspect ratio of 0.4. From the droplet impact test, it was found that the impact speed of water droplets and the curvature of the surface can greatly affect the dynamic performance of water. This work is expected to be of significant research value and importance for developing functional deformable skin materials.

| S-EPMC10536611 | biostudies-literature

A Superhydrophobic Moso Bamboo Cellulose Nano-Fibril Film Modified by Dopamine Hydrochloride.

Project description:The moso bamboo fiber powder was used as raw material to prepare cellulose nano-fibril films, 5% of polyvinyl alcohol solution was used as a structural reinforcement agent, dopamine hydrochloride (DA) was used as a surface adhesive, and hexadecyl trimethoxy silane was used as a surface modifier. The superhydrophobic films were prepared by vacuum filtration and impregnation. The results showed that the water contact angle on the surface of the film could reach 156°. The microstructure and chemical composition of the film surface was further studied by scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), and roughness measurement The scanning electron microscopy images showed that the nanofibers on the surface of Cellulose nanofibers film were arranged and randomly distributed, thus forming a dense network interwoven structure. In PDA hydrophobic modification solution, an Hexadecyltrimethoxysilane was hydrolyzed to a hexadecyl silanol to obtain the polar terminal hydroxyl of Hexadecyl silanol molecule. The -OCH3 terminal group of HDTMS reacted with hydroxyl/H2O to form a silanol (Si-OH) bond and further condensed to form a Si-O-Si network. In addition, due to the hydrophilicity of the surface of the nano cellulose film, a large amount of-OH was adsorbed on the surface of the nano cellulose film, resulted in the chemical connection between cetyl groups, thus realized the grafting of cetyl long-chain alkyl groups onto the fibers of the nano cellulose film.The film showed good self-cleaning and waterproof properties, which can be widely used in wet environment packaging and building.

| S-EPMC8563781 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data