Defluoridation technology for drinking water and tea by green synthesized Fe3O4/Al2O3 nanoparticles coated polyurethane foams for rural communities.
Ontology highlight
ABSTRACT:
SUBMITTER: Kumari S
PROVIDER: S-EPMC5556065 | biostudies-other | 2017 Aug
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Green tea is a commonly consumed beverage in China. Epidemiological and animal data suggest tea and tea polyphenols may be preventive against various cancers, including breast cancer. Catechol-O-methyltransferase (COMT) catalyzes catechol estrogens and tea polyphenols. The COMT rs4680 AA genotype leads to lower COMT activity, which may affect the relationship between green tea consumption and breast cancer risk. We evaluated whether regular green tea consumption was associated with breast cancer risk among 3454 incident cases and 3474 controls aged 20-74 y in a population-based case-control study conducted in Shanghai, China during 1996-2005. All participants were interviewed in person about green tea consumption habits, including age of initiation, duration of use, brew strength, and quantity of tea. Odds ratios (OR) and 95% CI were calculated for green tea consumption measures and adjusted for age and other confounding factors. Compared with nondrinkers, regular drinking of green tea was associated with a slightly decreased risk for breast cancer (OR, 0.88; 95% CI, 0.79-0.98). Among premenopausal women, reduced risk was observed for years of green tea drinking (P-trend = 0.02) and a dose-response relationship with the amount of tea consumed per month was also observed (P-trend = 0.046). COMT rs4680 genotypes did not have a modifying effect on the association of green tea intake with breast cancer risk. Drinking green tea may be weakly associated with a decreased risk of breast cancer.
| S-EPMC2646205 | biostudies-literature
Project description:Consistent and proper use of respiratory protective devices (RPD) is one of the essential actions that can be taken to reduce the risk of exposure to airborne hazards, i.e., biological and nonbiological aerosols, vapours, and gases. Proper fit of the facepiece and comfort properties of RPDs play a crucial role in effective protection and acceptance of RPDs by workers. The objective of the present paper was to develop viscoelastic polyurethane foams for use in RPD seals characterised by proper elasticity, allowing for the enhancement of the device fit to the face and the capability of removing moisture from the skin in order to improve the comfort of RPD use. Moreover, it was pivotal to ensure the non-flammability of the foams, as well as a simultaneous reduction in their cytotoxicity. The obtained foams were characterised using scanning electron microscopy, infrared spectroscopy, thermogravimetry, and differential scanning calorimetry. Measurements also involved gel fraction, apparent density, compression set, rebound resilience, wettability, flammability, and cytotoxicity. The results are discussed in the context of the impact of modifications to the foam formulation (i.e., flame-retardant type and content) on the desired foam properties. The test results set directions for future works aimed to develop viscoelastic polyurethane foams that could be applied in the design of respiratory protective devices.
| S-EPMC8746040 | biostudies-literature
Project description:Polyurethane (PU) is widely used in many aspects of modern life because of its versatility and resistance. However, PU waste disposal generates large problems, since it is slowly degraded, there are limited recycling processes, and its destruction may generate toxic compounds. In this work, we isolated fungal strains able to grow in mineral medium with a polyester PU (PS-PU; Impranil DLN) or a polyether PU (PE-PU; Poly Lack) varnish as the only carbon source. Of the eight best Impranil-degrading strains, the six best degraders belonged to the Cladosporium cladosporioides complex, including the species C. pseudocladosporioides, C. tenuissimum, C. asperulatum, and C. montecillanum, and the two others were identified as Aspergillus fumigatus and Penicillium chrysogenum The best Impranil degrader, C. pseudocladosporioides strain T1.PL.1, degraded up to 87% after 14 days of incubation. Fourier transform infrared (FTIR) spectroscopy analysis of Impranil degradation by this strain showed a loss of carbonyl groups (1,729 cm(-1)) and N-H bonds (1,540 and 1,261 cm(-1)), and gas chromatography-mass spectrometry (GC-MS) analysis showed a decrease in ester compounds and increase in alcohols and hexane diisocyanate, indicating the hydrolysis of ester and urethane bonds. Extracellular esterase and low urease, but not protease activities were detected at 7 and 14 days of culture in Impranil. The best eight Impranil-degrading fungi were also able to degrade solid foams of the highly recalcitrant PE-PU type to different extents, with the highest levels generating up to 65% of dry-weight losses not previously reported. Scanning electron microscopy (SEM) analysis of fungus-treated foams showed melted and thinner cell wall structures than the non-fungus-treated ones, demonstrating fungal biodegradative action on PE-PU.Polyurethane waste disposal has become a serious problem. In this work, fungal strains able to efficiently degrade different types of polyurethanes are reported, and their biodegradative activity was studied by different experimental approaches. Varnish biodegradation analyses showed that fungi were able to break down the polymer in some of their precursors, offering the possibility that they may be recovered and used for new polyurethane synthesis. Also, the levels of degradation of solid polyether polyurethane foams reported in this work have never been observed previously. Isolation of efficient polyurethane-degrading microorganisms and delving into the mechanisms they used to degrade the polymer provide the basis for the development of biotechnological processes for polyurethane biodegradation and recycling.
| S-EPMC4988181 | biostudies-literature
Project description:A novel synthesis of polyurethane foam/polyurethane aerogel (PUF-PUA) composites is presented. Three different polyurethane reticulated foams which present the same density but different pore sizes (named S for small, M for medium, and L for large) have been used. After the characterization of the reference materials (either, foams, and pure aerogel), the obtained composites have been characterized in order to study the effect of the foam pore size on the final properties, so that density, shrinkage, porous structure, mechanical properties, and thermal conductivity are determined. A clear influence of the pore size on the density and shrinkage was found, and the lowest densities are those obtained from L composites (123 kg/m3). Moreover, the aerogel density and shrinkage have been significantly reduced through the employment of the polyurethane (PU) foam skeleton. Due to the enhanced mechanical properties of polyurethane aerogels, the inclusion of polyurethane aerogel into the foam skeleton helps to increase the elastic modulus of the foams from 0.03 and 0.08 MPa to 0.85 MPa, while keeping great flexibility and recovery ratios. Moreover, the synthesized PUF-PUA composites show an excellent insulating performance, reducing the initial thermal conductivity values from 34.1, 40.3, and 50.6 mW/(m K) at 10 °C for the foams S, M, and L, to 15.8, 16.6, and 16.1 mW/(m K), respectively. Additionally, the effect of the different heat transfer mechanisms to the total thermal conductivity is herein analyzed by using a theoretical model as well as the influence of the measurement temperature.
| S-EPMC9268151 | biostudies-literature
Project description:In recent years, iron-based nanoparticles (FeNPs) have been successfully used in environmental remediation and water treatment. This study examined ecotoxicity of two FeNPs produced by green tea extract (smGT, GTFe) and their ability to degrade malachite green (MG). Their physicochemical properties were assessed using transmission electron microscopy, X-ray powder diffraction, dynamic light scattering, and transmission Mössbauer spectroscopy. Using a battery of ecotoxicological bioassays, we determined toxicity for nine different organisms, including bacteria, cyanobacterium, algae, plants, and crustaceans. GTFe, amorphous complex of Fe(II, III) ions and polyphenols from green tea extract, proved low capacity to degrade MG and was toxic to all tested organisms. Superparamagnetic iron oxide NPs (smGT) derived from GTFe, showed no toxic effect on most of the tested organisms up to a concentration of 1g/L, except for algae and cyanobacterium and removed 93 % MG at concentration 125 mg Fe/L after 60 minutes. The procedure described in this paper generates new superparamagnetic iron oxide NPs from existing and toxic GTFe, which are nontoxic and has degradative potential for organic compounds. These findings suggest low ecotoxicological risks and suitability of this green-synthesized FeNPs for environmental remediation purposes.
| S-EPMC6093305 | biostudies-literature
Project description:Water-blown polyurethane (PU) foams are of enormous technological interest as they are widely applied in various fields, i.e., consumer goods, medicine, automotive or aerospace industries. The discovery of the one-way shape-memory effect in PU foams provided a fresh impetus for extensive investigations on porous polymeric actuators over the past decades. High expansion ratios during the shape-recovery are of special interest when big volume changes are required, for example to fill an aneurysm during micro-invasive surgery or save space during transportation. However, the need to program the foams before each operation cycle could be a drawback impeding the entry of shape-memory polymeric (SMP) foams to our daily life. Here, we showed that a reversible shape-memory effect (rSME) is achievable for polyurethane water-blown semicrystalline foams. We selected commercially available crystallizable poly(ε-caprolactone)-diols of different molecular weight for foams synthesis, followed by investigations of morphology, thermal, thermomechanical and shape-memory properties of obtained compositions. Densities of synthesized foams varied from 110 to 180 kg∙m-3, while peak melting temperatures were composition-dependent and changed from 36 to 47 °C, while the melting temperature interval was around 15 K. All semicrystalline foams exhibited excellent one-way SME with shape-fixity ratios slightly above 100% and shape-recovery ratios from the second cycle of 99%. The composition with broad distribution of molecular weights of poly(ε-caprolactone)-diols exhibited an rSME of about 12% upon cyclic heating and cooling from Tlow = 10 °C and Thigh = 47 °C. We anticipate that our experimental study opens a field of systematic investigation of rSMEs in porous polymeric materials on macro and micro scale and extend the application of water-blown polyurethane foams to, e.g., protective covers with zero thermal expansion or even cushions adjustable to a certain body shape.
| S-EPMC6431911 | biostudies-literature
Project description:One of the essential factors in prostheses is their fitting. To assemble a prosthesis with the residual limb, so-called liners are used. Liners used currently are criticized by users for their lack of comfort, causing excessive sweating and skin irritation. The objective of the work was to develop viscoelastic polyurethane foams for use in limb prostheses. As part of the work, foams were produced with different isocyanate indexes (0.6-0.9) and water content (1, 2 and 3 php). The produced foams were characterized by scanning electron microscopy, computer microtomography, infrared spectroscopy, thermogravimetry and differential scanning calorimetry. Measurements also included apparent density, recovery time, rebound elasticity, permanent deformation, compressive stress value and sweat absorption. The results were discussed in the context of modifying the foam recipe. The performance properties of the foams, such as recovery time, hardness, resilience and sweat absorption, indicate that foams that will be suitable for prosthetic applications are foams with a water content of 2 php produced with an isocyanate index of 0.8 and 0.9.
| S-EPMC8746291 | biostudies-literature
Project description:Acidolysis is emerging as a promising method for recycling polyurethane foam (PUF) waste. Here, we present highly efficient acidolysis of PUFs with adipic acid (AA) by heating the reaction mixtures with microwaves. The influence of experimental conditions, such as reaction temperature, time, and amount of the degradation reagent, on the polyol functionality, molecular weight characteristics, the presence of side products, and the degree of degradation of the remaining PUF hard segments was studied by matrix-assisted laser desorption/ionization time-of-flight mass spectroscopy (MALDI-TOF MS), nuclear magnetic resonance (NMR), size-exclusion chromatography (SEC) coupled to a multidetection system, and Fourier transform infrared (FT-IR) spectroscopy. The purified recycled polyols were used for the synthesis of flexible PUFs. The morphology and mechanical properties of the PUFs show that the degree of functionalization of the polyol by the carboxylic end groups, which is higher for larger amounts of AA used to degrade the PUFs, significantly affects the quality and performance of the flexible PUFs from the recycled polyols.
| S-EPMC8790754 | biostudies-literature
Project description:Alumina/polyurethane composites were prepared via in situ polymerization and used as thermal interface materials (TIMs). The surface of alumina particles was modified using polydopamine (PDA) and then evaluated via Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG), and Raman spectroscopy (Raman). Scanning electron microscope (SEM) images showed that PDA-Al2O3 has better dispersion in a polyurethane (PU) matrix than Al2O3. Compared with pure PU, the 30 wt% PDA-Al2O3/PU had 95% more Young's modulus, 128% more tensile strength, and 76% more elongation at break than the pure PU. Dynamic mechanical analysis (DMA) results showed that the storage modulus of the 30 wt% PDA-Al2O3/PU composite improved, and the glass transition temperature (Tg) shifted to higher temperatures. The thermal conductivity of the 30 wt% PDA-Al2O3/PU composite increased by 138%. Therefore, the results showed that the prepared PDA-coated alumina can simultaneously improve both the mechanical properties and thermal conductivity of PU.
| S-EPMC7179027 | biostudies-literature
Project description:Hydrophilic, flexible polyurethane (FPU) foams made from Hypol prepolymers are capable of retaining large amounts of water and saline solutions. The addition of different catalysts and surfactant agents to Hypol JM 5008 prepolymer was assayed to obtain a foam with good structural stability and elasticity. The combination of three catalysts, stannous octoate and two amine-based ones (Tegoamin 33 and Tegoamin BDE), and the surfactant Niax silicone L-620LV allowed to synthesize a foam with a homogeneous cell size distribution, exhibiting the highest saline absorption capacity (2.4 g/gram of foam) and almost complete shape recovery, with up to a 20% of remaining deformation. Then, superabsorbent sodium acrylate polymer (PNaA) was added to the FPU foam up to 8 pph. The urine absorption capacity of the foam was increased about 24.8% by incorporating 6 pph of PNaA, absorbing 17.46 g of saline solution per foam gram, without any negative impact on the rest of the foam properties. All these properties make the synthesized foams suitable for corporal fluids absorption applications in which elasticity and low-density are required.
| S-EPMC8123336 | biostudies-literature