Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Physical Properties and Precipitate Microstructures of Cu-Hf Alloys at Different Processing Stages.

ABSTRACT: The microstructural evolution and hardness and physical properties of a Cu-Hf alloy at the different processing stages were investigated using hardness, conductivity and tensile measurements, metallographic microscopy, scanning electron microscopy, and transmission electron microscopy. The results reveal that the electrical conductivity of these alloys was above 80% IACS after aging at 450°C, and the hardness and conductivity of the Cu-0.9Hf alloy were 180?HV0.5 and 80% IACS, respectively. The softening temperature of the Cu-0.15Hf alloy is 525°C, and the softening temperature of Cu-0.4Hf and Cu-0.9Hf alloys is 550°C. The precipitated Hf-containing phase exhibited a short rod-like structure, the size of which increased with aging time at a slow rate and resulted in the size of ~20?nm after aging at 450°C for 300?min.

SUBMITTER: Li M

PROVIDER: S-EPMC6311750 | biostudies-other | 2018

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Publications

Physical Properties and Precipitate Microstructures of Cu-Hf Alloys at Different Processing Stages.

Li Mingmao M Zhang Leqing L Zhu Mingbiao M Wang Hang H Wei Haigen H

Scanning 20181217

The microstructural evolution and hardness and physical properties of a Cu-Hf alloy at the different processing stages were investigated using hardness, conductivity and tensile measurements, metallographic microscopy, scanning electron microscopy, and transmission electron microscopy. The results reveal that the electrical conductivity of these alloys was above 80% IACS after aging at 450°C, and the hardness and conductivity of the Cu-0.9Hf alloy were 180 HV0.5 and 80% IACS, respectively. The s ...[more]

PMID: 30647805

Similar Datasets

Characterization of Microstructures and Tensile Properties of Recycled Al-Si-Cu-Fe-Mn Alloys with Individual and Combined Addition of Titanium and Cerium.

Project description:Individual and combined addition of Ti and Ce on the recycled Al-Si-Cu-Fe-Mn alloy was conducted. The microstructures and tensile properties of these fabricated alloys were investigated. In the case of Ti or Ce which was individually added, the added amount was ranging from 0.03?wt.% to 0.09?wt.%. The combined addition of Ti and Ce was set at the ratios of 1?:?1, 1?:?3, and 3?:?1 with a total amount of 0.12?wt.%. Microstructures and phases of these alloys were investigated by using an optical microscope, X-ray diffraction testing, and SEM coupled with EDS. The morphologies of these alloys were quantified by analyzing the SDAS value, length of secondary phases, and phases' distribution uniformity. Tensile testing was carried out for understanding the strengthen effect of the modification process. Results show that the addition of Ce was favorable to the strength and % elongation because the coarse needle-like phase and the polyhedral phase were effectively refined. Their SDAS values and distribution factor were remarkably declined with the increase of the Ce level. The Ti addition could also refine the secondary phases and SDAS values. But its effect was not as prominent as the addition of Ce. Combined addition of Ti and Ce elements at the ratio of 1?:?3 resulted in the samples reaching maximum comprehensive tensile properties. In this case, the short needle-like phase was uniformly distributed in the microstructure. Few polyhedral phases could be found in the Al-Si-Cu-Fe-Mn matrix. The strengthening of these fabricated materials was due to the grain refinement for ?-Al and modification for coarse secondary phases. In addition, distribution uniformity of secondary phases was also changed by their modification effects.

| S-EPMC6311731 | biostudies-literature

Microstructures and Mechanical Properties of Co-Cr Dental Alloys Fabricated by Three CAD/CAM-Based Processing Techniques.

Project description:The microstructures and mechanical properties of cobalt-chromium (Co-Cr) alloys produced by three CAD/CAM-based processing techniques were investigated in comparison with those produced by the traditional casting technique. Four groups of disc- (microstructures) or dumbbell- (mechanical properties) specimens made of Co-Cr alloys were prepared using casting (CS), milling (ML), selective laser melting (SLM), and milling/post-sintering (ML/PS). For each technique, the corresponding commercial alloy material was used. The microstructures of the specimens were evaluated via X-ray diffractometry, optical and scanning electron microscopy with energy-dispersive X-ray spectroscopy, and electron backscattered diffraction pattern analysis. The mechanical properties were evaluated using a tensile test according to ISO 22674 (n = 6). The microstructure of the alloys was strongly influenced by the manufacturing processes. Overall, the SLM group showed superior mechanical properties, the ML/PS group being nearly comparable. The mechanical properties of the ML group were inferior to those of the CS group. The microstructures and mechanical properties of Co-Cr alloys were greatly dependent on the manufacturing technique as well as the chemical composition. The SLM and ML/PS techniques may be considered promising alternatives to the Co-Cr alloy casting process.

| S-EPMC5456947 | biostudies-other

Enhancement of the Mechanical Properties in Al?Si?Cu?Fe?Mg Alloys with Various Processing Parameters.

Project description:In this research, various processing conditions were implemented to enhance the mechanical properties of Al-Si alloys. The silicon content was varied from hypoeutectic (Si-10 wt.%) to eutectic (Si-12.6 wt.%) and hypereutectic (Si-14 wt.%) for the preparation of Al-XSi-3Cu-0.5Fe-0.6 Mg (X = 10?14%) alloys using die casting. Subsequently, these alloys were hot-extruded with an optimum extrusion ratio (17:1) at 400 °C to match the output extruded bar to the compressor size. An analysis of the microstructural features along with a chemical compositional analysis were carried out using scanning electron microscope along with energy dispersive X-ray spectroscopy and transmission electron microscope. The SEM micrographs of the extruded samples displayed cracks in primary Si, and the intermetallic (?-Al?FeSi) phase was fragmented accordingly. In addition, the silicon phase was homogenously distributed, and the size remained constant. The mechanical properties of the extruded samples were enhanced by the increase of silicon content, and consequently the ductility decreased. By implementing proper T6 heat treatment parameters, coherent Al?Cu phases were formed in the Al matrix, and the Si phase was gradually increased along with the silicon content. Therefore, high tensile strength was achieved, reaching values for the Al-XSi-3Cu-0.5Fe-0.6Mg (X = 10?14%) alloys of 366 MPa, 388 MPa, and 420 MPa, respectively.

| S-EPMC6266997 | biostudies-other

Novel Ti-Ta-Hf-Zr alloys with promising mechanical properties for prospective stent applications.

Project description:Titanium alloys are receiving increasing research interest for the development of metallic stent materials due to their excellent biocompatibility, corrosion resistance, non-magnetism and radiopacity. In this study, a new series of Ti-Ta-Hf-Zr (TTHZ) alloys including Ti-37Ta-26Hf-13Zr, Ti-40Ta-22Hf-11.7Zr and Ti-45Ta-18.4Hf-10Zr (wt.%) were designed using the d-electron theory combined with electron to atom ratio (e/a) and molybdenum equivalence (Moeq) approaches. The microstructure of the TTHZ alloys were investigated using optical microscopy, XRD, SEM and TEM and the mechanical properties were tested using a Vickers micro-indenter, compression and tensile testing machines. The cytocompatibility of the alloys was assessed using osteoblast-like cells in vitro. The as-cast TTHZ alloys consisted of primarily ? and ? nanoparticles and their tensile strength, yield strength, Young's modulus and elastic admissible strain were measured as being between 1000.7-1172.8 MPa, 1000.7-1132.2 MPa, 71.7-79.1 GPa and 1.32-1.58%, respectively. The compressive yield strength of the as-cast alloys ranged from 1137.0 to 1158.0 MPa. The TTHZ alloys exhibited excellent cytocompatibility as indicated by their high cell viability ratios, which were close to that of CP-Ti. The TTHZ alloys can be anticipated to be promising metallic stent materials by virtue of the unique combination of extraordinarily high elastic admissible strain, high mechanical strength and excellent biocompatibility.

| S-EPMC5126583 | biostudies-literature

Analysis of the Influence of Starting Materials and Processing Conditions on the Properties of W/Cu Alloys.

Project description:In this work, a study of the influence of the starting materials and the processing time used to develop W/Cu alloys is carried out. Regarding powder metallurgy as a promising fabrication route, the difficulties in producing W/Cu alloys motivated us to investigate the influential factors on the final properties of the most industrially demanding alloys: 85-W/15-Cu, 80-W/20-Cu, and 75-W/25-Cu alloys. Two different tungsten powders with large variation among their particle size-fine (Wf) and coarse (Wc) powders-were used for the preparation of W/Cu alloys. Three weight ratios of fine and coarse (Wf:Wc) tungsten particles were analyzed. These powders were labelled as "tungsten bimodal powders". The powder blends were consolidated by rapid sinter pressing (RSP) at 900 °C and 150 MPa, and were thus sintered and compacted simultaneously. The elemental powders and W/Cu alloys were studied by optical microscopy (OM) and scanning electron microscopy (SEM). Thermal conductivity, hardness, and densification were measured. Results showed that the synthesis of W/Cu using bimodal tungsten powders significantly affects the final alloy properties. The higher the tungsten content, the more noticeable the effect of the bimodal powder. The best bimodal W powder was the blend with 10 wt % of fine tungsten particles (10-Wf:90-Wc). These specimens present good values of densification and hardness, and higher values of thermal conductivity than other bimodal mixtures.

| S-EPMC5459155 | biostudies-other

Shear band-driven precipitate dispersion for ultrastrong ductile medium-entropy alloys.

Project description:Precipitation strengthening has been the basis of physical metallurgy since more than 100 years owing to its excellent strengthening effects. This approach generally employs coherent and nano-sized precipitates, as incoherent precipitates energetically become coarse due to their incompatibility with matrix and provide a negligible strengthening effect or even cause brittleness. Here we propose a shear band-driven dispersion of nano-sized and semicoherent precipitates, which show significant strengthening effects. We add aluminum to a model CoNiV medium-entropy alloy with a face-centered cubic structure to form the L21 Heusler phase with an ordered body-centered cubic structure, as predicted by ab initio calculations. Micro-shear bands act as heterogeneous nucleation sites and generate finely dispersed intragranular precipitates with a semicoherent interface, which leads to a remarkable strength-ductility balance. This work suggests that the structurally dissimilar precipitates, which are generally avoided in conventional alloys, can be a useful design concept in developing high-strength ductile structural materials.

| S-EPMC8338972 | biostudies-literature

Reduced partitioning of plastic strain for strong and yet ductile precipitate-strengthened alloys.

Project description:When a material that contains precipitates is deformed, the precipitates and the matrix may strain plastically by different amounts causing stresses to build up at the precipitate-matrix interfaces. If premature failure is to be avoided, it is therefore essential to reduce the difference in the plastic strain between the two phases. Here, we conduct nanoscale digital image correlation to measure a new variable that quantifies this plastic strain difference and show how its value can be used to estimate the associated interfacial stresses, which are found to be approximately three times greater in an Fe-Ni2AlTi steel than in the more ductile Ni-based superalloy CMSX-4®. It is then demonstrated that decreasing these stresses significantly improves the ability of the Fe-Ni2AlTi microstructure to deform under tensile loads without loss in strength.

| S-EPMC5989271 | biostudies-literature

Microstructures and Properties of Sn2.5Ag0.7Cu0.1RE Composite Solders Reinforced with Cu-Coated Graphene Nanosheets Synthesized by Pyrolysis.

Project description:Composite solder is a promising route to improve the properties and reliability of Sn-based lead-free solder. In this study, Cu-coated graphene nanosheets (Cu-GNSs) were synthesized using pyrolysis. Cu-GNSs reinforced Sn2.5Ag0.7Cu0.1RE composite lead-free solders were prepared via powder metallurgy. The size, distribution, and adsorption type of Cu nanoparticles on the GNSs were studied. The relation of the Cu-GNSs content and microstructure to the physical, wettability, and mechanical properties of composite solders was discussed. The results show that Cu nanoparticles (with a mean size of 13 nm) present uniform distribution and effective chemisorptions on the GNS. Microstructural evolution of composite solders is dependent on the addition of Cu-GNSs. With increasing Cu-GNSs addition, ?-Sn grains become finer and the eutectic phase proportion becomes larger, while the morphology of the eutectic phase transforms from dispersion to network-type. The improvement of the tensile strength of the composite solder can be attributed to grain refinement and load transfer. While the existence of Cu-GNSs can effectively improve the wettability and slightly change the melting point, it can also lead to the decline of elongation and electrical conductivity of the composite solder.

| S-EPMC6357091 | biostudies-literature

The Influence of Cu-Additions on the Microstructure, Mechanical and Magnetic Properties of MnAl-C Alloys.

Project description:Alloys of the form (Mn54Al44C2)100-xCux (with x?=?0, 1, 2, 4 and 6) were produced by induction melting. After homogenisation and quenching, most of the alloys consist entirely of the retained ?-phase, except for x?=?6, in which the ?-phase was additionally present. After subsequent annealing, the alloys with x???2 consist entirely of a Cu-doped, ferromagnetic ?-phase, whereas the alloys with x?>?2 additionally contain the ?-phase. The polarisation of the alloys at an applied field of 14?T decreases with increasing Cu-content, which is attributed i) to the dilution of the magnetic moment of the ?-phase unit cell by the Cu atoms, which do not carry a magnetic moment, and ii) at higher Cu-contents, to the formation of the ?-phase, which has a much lower polarisation than the ?-phase and therefore dilutes the net polarisation of the alloys. The Curie temperature was not affected by the Cu-additions. The stress needed to die-upset the alloys with x???2 was similar to that of the undoped alloy, whereas it was much lower for x?=?4 and 6, due to the presence of intergranular layers of the ?-phase. The extrinsic magnetic properties of alloys with x???2 were improved by die-upsetting, whereas decomposition of the ?-phase during processing had a deleterious effect on the magnetic properties for higher Cu-additions.

| S-EPMC7217857 | biostudies-literature

Different Stages, Different Signals: The Modulating Effect of Cognitive Conflict on Subsequent Processing.

Project description:The present study used event-related potentials (ERPs) to investigate the function of signals induced by cognitive conflict during the detection stage and the resolution stage of perceptual processing. The study used a combination of the Stroop task and an affective priming task to examine the conflict priming effect when the stimulus onset asynchrony (SOA) was 200 ms or 800 ms. Behavioral results showed that the RTs were shorter for positive targets following congruent primes relative to incongruent primes, and for negative targets following incongruent primes relative to congruent primes when the SOA was 200 ms. ERP results showed that the N2 amplitudes (200-300 ms) for incongruent stimuli were significantly larger than for congruent stimuli in the Stroop task, which indicated a significant conflict effect. Moreover, the N400 amplitudes (500-700 ms) for positive targets after congruent primes were significantly lower than those after incongruent primes when the SOA was 200 ms, which showed a significant negative priming effect. While the SOA was 800 ms, behavioral results showed that the RTs were shorter for positive targets following incongruent primes relative to congruent primes. ERP results showed that the N2 amplitudes (200-300 ms) for incongruent stimuli were significantly larger than for congruent stimuli in the Stroop task, which indicated a significant conflict effect. The N400 amplitudes (1100-1300 ms) for the negative targets after congruent primes were significantly lower than those after incongruent primes when the SOA was 800 ms, which showed a significant positive priming effect. The results demonstrated that the functions of signals induced by cognitive conflict were reversed in two different cognitive processing stages.

| S-EPMC5026368 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data