Serum metabolomics-based study of Alzheimer's disease and Mild cognitive impairment patients.
Ontology highlight
ABSTRACT:
INSTRUMENT(S): Xevo G3 QTof
ORGANISM(S): Homo Sapiens (ncbitaxon:9606)
SUBMITTER: 
Helen Gika
PROVIDER: MSV000096802 | MassIVE | Wed Jan 08 06:18:00 GMT 2025
REPOSITORIES: MassIVE
Similar Datasets
Project description:<p>The sample to be tested was fully ground into powder in the grinder, 50 mg of the sample was freeze-dried, 1000 μL of the extraction solution containing the inner target was added (methanol:acetonitrile:water, 2:2:1, v/v/v, internal standard concentration 20 mg/L) and vortex mixed for 30 s; then add the steel ball to the 45 Hz grinder for 10 min, ultrasonic 10 min; the sample to be tested is obtained after filtration. When detecting metabolites, metabolite determination was performed based on the LC-MS system, which mainly consists of Waters Acquity I-Class PLUS ultra-high performance liquid tandem and Waters Xevo G2-XS QTof high-resolution mass spectrometer. Meanwhile, the Waters Acquity UPLC HSS T3 column (1.8 um 2.1 x 100 mm) was used as the chromatographic column. Positive and negative ion modes were used to determine the metabolites. Mobile phase A: 0.1% formic acid aqueous solution; Mobile phase B: 0.1% acetonitrile formate. The mobile phase conditions of liquid chromatography were as follows: the flow rate was 400 μL/min, 0.0 min: 98% flow A, 2% flow B; 0.25 min: 98% flow A, 2% flow B, 10.0 min: 2% flow A, 98% flow B; 13.0 min: 2% flow A, 98% flow B; 13.1 min: 98% flow A, 2% flow B; 15.0 min: 98% flow A, 2% flow B. MSe mode controlled by acquisition software (MassLynx v4.2, Waters) was used for primary and secondary mass spectrum data acquisition. ESI ion source parameters are as follows: Capillary voltage, 2500 V (positive ion mode) or -2000 V (negative ion mode); Cone hole voltage, 30 V; Ion source temperature, 100 °C; Desolvent temperature, 500 °C; Air flow rate, 50 L/h; Desolvent gas flow rate, 800 L/h; Plastic-nucleus ratio (m/z) collection range 50-1200 m/z. In the qualitative and quantitative analysis of metabolites, the original data collected by MassLynx v4.2 were processed by the Progenesis QI software for peak extraction, peak alignment, and other data, and the metabolites were identified based on the Progenesis QI software online METLIN database. Then, based on the results of the total score, MS2 score, and mass error (ppm), the metabolites were qualitatively determined.</p>
2024-07-12 | MTBLS10002 | MetaboLights
Project description:Pretreated human follicular fluid was prepared for targeted metabolomics experiments. For this purpose, 12-point standard calibration curves in the respective range with reference material were measured, and the limit of detection (LOD) and limit of quantification (LOQ) for each neurotransmitter under investigation were calculated. LC-MS/MS was conducted by an ultra-performance liquid chromatography method using a Waters ACQUITY UPLC BEH C18 column (2.1 mm×100 mm, 1.7 µm, Waters, USA). The Waters acquisition UPLC was coupled to an API 4000 triple quadrupole mass spectrometer (AB SCIEX, USA). The mobile phase A buffer was 10% methanol in water (containing 0.1% formic acid), and the mobile phase B buffer was 50% methanol in water (containing 0.1% formic acid). The LC gradient elution was at a flow rate of 0.3 mL/min at 0-8.0 min and 0.4 ml/min at 8.0-17.5 min, then 10%-30% B at 0-6.5 min; 30%-100% B at 6.5-7 min; 100% B at 7-14min; and 100%-10% B at 14-17.5min. The injection volume was 5 µl and the column temperature was set to 40 °C. Twenty-three metabolites (Ach: Acetylcholine chloride; Gln: Glutamine; Glu: Glutamate; His: L-Histidine; NE: norepinephrine; Tyr:Tyrosine; Trp:Tryptophan; Kyn: Kynurenine; GABA: 4-Aminobutyric acid;HisA:Histamine; PA:Picolinic acid;TyrA:Tyramine;DA:Hydroxytyramine hydrochloride; TrpA:Tryptamine;5-HT:Serotonin hydrochloride;E:Adrenaline hydrochloride;KynA:Kynurenic acid;5-HIAA:5-Hydroxyindole-3-acetic acid;DOPA:Levodopa;XA:Xanthurenic acid;VWA:Vanillymandelic Acid; 5-HTTP:5-Hydroxytryptophan;MT:Melatonine)were simultaneously reported in LC-MS/MS multiple reaction monitoring (MRM) mode. Data analysis was performed with Analyst 1.6 software.
2022-08-12 | PXD031560 | Pride
Project description:Alzheimer case-control samples originate from the EU funded AddNeuroMed Cohort, which is a large cross-European AD biomarker study relying on human blood as the source of RNA.
2015-08-05 | GSE63061 | GEO
Project description:Alzheimer case-control samples originate from the EU funded AddNeuroMed Cohort, which is a large cross-European AD biomarker study relying on human blood as the source of RNA. The design is case-control. Cases are either Alzheimer's disease patients, subjects with mild cognitive impairment or age and gender matched controls.
2015-08-05 | E-GEOD-63061 | biostudies-arrayexpress
Project description:Quantitative label-free proteomics study comparing brain samples from subjects with Cerebral amyloid angiopathy, Alzheimer desease and healthy Control groups.
2024-03-25 | MSV000094400 | MassIVE
Project description:Alzheimer, Mild Cognitive impairment and control samples from AddneuroMed Cohort
| PRJNA266528 | ENA
Project description:LC-MS/MS metabolomics data of Komagataella phaffii recorded on a Q Exactive HF in positive and negative ion mode. ACQUITY UPLC BEH Amide column 2.1 x 100 mm, 1.7 uM (Waters Corp., Milford, MA) column A: 100% H2O, 10 mM HCOONH4, 0.1% formic acid B: 80% ACN, 20% H2O, 10 mM HCOONH4, 0.1% formic acid.
2022-07-28 | MSV000090004 | GNPS
Project description:Multiple Affinity Removal Spin Cartridge Human 14 kit (Agilent) was used to remove 14 major proteins from plasma. Samples were denatured with an equivalent volume of trifluoroethanol and reduced with dithiothreitol. Free cysteine residues were alkylated with iodoacetamide. Samples were incubated with trypsin and desalted with C18 ZipTip. Desalted samples were rehydrated in 0.1% formic acid (FA) and were analyzed by LC-MS using a nanoLC Eksigent 400 system (Eksigent, AB Sciex), coupled online to an TripleTOF6600 mass spectrometer (AB Sciex). Peptide separation was performed using liquid chromatography with a trap and elution configuration using a nano trap column (350 μm × 0.5 mm, 3 μm, 120 Å, AB Sciex) and a nano ChromXP C18 reverse phase column (75 μm × 15 cm, 3 μm, 120 Å, AB Sciex) at 300 nl/min with a 90 min linear gradient of 8-30% acetonitrile in 0.1% FA, and then, with a 10 min linear gradient of 30% to 40% acetonitrile in 0.1% FA. The mass spectrometer was operated in information-dependent acquisition (IDA) mode, scanning full spectra (400–1500 m/z) for 250 ms, followed by up to 30 MS/MS scans (100–1800 m/z for 50 ms each), for a cycle time of 1.8 s. Candidate ions with a charge state between +2 and + 5 and counts above a minimum threshold of 125 counts per second were isolated for fragmentation, and one MS/MS spectrum was collected before adding those ions to the exclusion list for 12 s. Rolling collision energy was used with a collision energy spread of 15. The mass spectrometer was operated using the Analyst TF 1.7.1 software program (AB Sciex). For data dependent acquisition (DDA, SWATH acquisition), the parameters were set as follows: 100 ms TOF MS scan, followed by 200 variable SWATH windows each at 50 ms accumulation time for m/z 400–1250. MS/MS SWATH scans were set at 5 Da window overlapping by 1 Da for m/z 400–1250 and varied on each side of the mass range. The total cycle time was 9.6 s. A rolling collision energy (CE) parameters script was used to automatically control the CE. Acquired spectra were searched against the UniProt reviewed database using the Paragon algorithm embedded in the ProteinPilot 5.0.1 software program (AB Sciex), with the following search parameters: (i) sample type: identification, (ii) Cys alkylation: iodoacetamide, (iii) digestion: trypsin, (iv) instrument: TripleTOF 6600, (v) species: Homo sapiens, (vi) ID focus: biological modifications, (vii) detected protein threshold: > 0.05 (10% confidence). The detected protein threshold was set to the minimum level to enhance the number of wrong answers to enable the curve fitting by an independent FDR analysis. This was carried out by the target-decoy approach provided with the ProteinPilot software program, which was used to assess the quality of the identifications. Positive identifications were considered when identified proteins and peptides reached a 1% local FDR. The resulting group file was loaded into Peakview (v2.2.0, AB Sciex) and peaks from SWATH runs were extracted with a peptide confidence threshold of 99% and a false discovery rate <1%. The SWATH files were then exported to the MarkerView software program (version 1.3.0.1; AB Sciex) and the peak areas of individual peptides were normalized to the sum of the peak areas of all detected peptides.
2022-05-11 | PXD025937 | JPOST Repository
Project description:Cervicovaginal lavage (CVL)supernatants were heat inactivated for 30 minutes at 56°C before further processing. Total protein concentrations were determined using the Pierce Coomassie Plus (Bradford) Protein Assay (Thermo Scientific, Rockford, IL, USA). Sample protein content and volume were normalised with 25mM ammonium bicarbonate (ABC). Soluble proteins were precipitated using an equal volume of ice cold 30% (w/v) TCA in acetone and incubated at -20⁰C for 2 hours. Samples were centrifuged at 12,000g for 10 minutes (4⁰C) to pellet proteins. Pellets were washed three times with ice cold acetone and allowed to air dry. Further sample processing was performed as previously described (Armstrong et al, 2014) with minor modifications. Briefly, protein pellets were resuspended in 25 mM ABC, 0.05%(w/v) rapigest (Waters), reduced and alkylated. Digestion was performed with proteomic-grade trypsin (Sigma-Aldrich, St. Louis, MO, USA) at a protein:trypsin ratio of 50:1. Rapigest was precipitated by addition of trifluoroacetic acid to a final concentration of 0.5% (v/v). Peptide mixtures were analyzed by on-line nanoflow liquid chromatography using the nanoACQUITY-nLC system (Waters MS technologies) coupled to an LTQ-Orbitrap Velos (ThermoFisher Scientific, Bremen, Germany) mass spectrometer equipped with the manufacturer’s nanospray ion source. The gradient of the analytic column (nanoACQUITY UPLCTM BEH130 C18 15cm x 75µm, 1.7µm capillary column) consisted of 3-40% acetonitrile in 0.1% formic acid for 90 min then a ramp of 40-85% acetonitrile in 0.1% formic acid for 5min.
2016-03-15 | PXD003176 | Pride
Project description:Multiple Affinity Removal Spin Cartridge Human 14 kit (Agilent) was used to remove 14 major proteins from plasma. Samples were denatured with an equivalent volume of trifluoroethanol and reduced with dithiothreitol. Free cysteine residues were alkylated with iodoacetamide. Samples were incubated with trypsin and desalted with C18 ZipTip. Desalted samples were rehydrated in 0.1% formic acid (FA) and were analyzed by LC-MS using a nanoLC Eksigent 400 system (Eksigent, AB Sciex), coupled online to an TripleTOF6600 mass spectrometer (AB Sciex). Peptide separation was performed using liquid chromatography with a trap and elution configuration using a nano trap column (350 μm × 0.5 mm, 3 μm, 120 Å, AB Sciex) and a nano ChromXP C18 reverse phase column (75 μm × 15 cm, 3 μm, 120 Å, AB Sciex) at 300 nl/min with a 90 min linear gradient of 8-30% acetonitrile in 0.1% FA, and then, with a 10 min linear gradient of 30% to 40% acetonitrile in 0.1% FA. The mass spectrometer was operated in information-dependent acquisition (IDA) mode, scanning full spectra (400–1500 m/z) for 250 ms, followed by up to 30 MS/MS scans (100–1800 m/z for 50 ms each), for a cycle time of 1.8 s. Candidate ions with a charge state between +2 and + 5 and counts above a minimum threshold of 125 counts per second were isolated for fragmentation, and one MS/MS spectrum was collected before adding those ions to the exclusion list for 12 s. Rolling collision energy was used with a collision energy spread of 15. The mass spectrometer was operated using the Analyst TF 1.7.1 software program (AB Sciex). For data dependent acquisition (DDA, SWATH acquisition), the parameters were set as follows: 100 ms TOF MS scan, followed by 200 variable SWATH windows each at 50 ms accumulation time for m/z 400–1250. MS/MS SWATH scans were set at 5 Da window overlapping by 1 Da for m/z 400–1250 and varied on each side of the mass range. The total cycle time was 9.6 s. A rolling collision energy (CE) parameters script was used to automatically control the CE. Acquired spectra were searched against the UniProt reviewed database using the Paragon algorithm embedded in the ProteinPilot 5.0.1 software program (AB Sciex), with the following search parameters: (i) sample type: identification, (ii) Cys alkylation: iodoacetamide, (iii) digestion: trypsin, (iv) instrument: TripleTOF 6600, (v) species: Homo sapiens, (vi) ID focus: biological modifications, (vii) detected protein threshold: > 0.05 (10% confidence). The detected protein threshold was set to the minimum level to enhance the number of wrong answers to enable the curve fitting by an independent FDR analysis. This was carried out by the target-decoy approach provided with the ProteinPilot software program, which was used to assess the quality of the identifications. Positive identifications were considered when identified proteins and peptides reached a 1% local FDR. The resulting group file was loaded into Peakview (v2.2.0, AB Sciex) and peaks from SWATH runs were extracted with a peptide confidence threshold of 99% and a false discovery rate <1%. The SWATH files were then exported to the MarkerView software program (version 1.3.0.1; AB Sciex) and the peak areas of individual peptides were normalized to the sum of the peak areas of all detected peptides.
2022-05-11 | PXD025945 | JPOST Repository