Fabrication of 3D microstructures from interactions of immiscible liquids with a structured surface.
Ontology highlight
ABSTRACT:
SUBMITTER: Balowski JJ
PROVIDER: S-EPMC3783858 | biostudies-literature | 2013 Aug
REPOSITORIES: biostudies-literature
Publications
Fabrication of 3D microstructures from interactions of immiscible liquids with a structured surface.
Balowski Joseph J JJ Wang Yuli Y Allbritton Nancy L NL
Advanced materials (Deerfield Beach, Fla.) 20130625 30
A new lithography technique is presented that exploits the interactions of immiscible liquids with a structured surface. This highly parallel, "low-tech" method requires no dedicated equipment and easily produces curved and/or multi-level structures out of a variety of photoactive and non-photoactive materials. ...[more]
Similar Datasets
Project description:Tissue architecture is a prerequisite for its biological functions. Recapitulating the three-dimensional (3D) tissue structure represents one of the biggest challenges in tissue engineering. Two-dimensional (2D) tissue fabrication methods are currently in the main stage for tissue engineering and disease modeling. However, due to their planar nature, the created models only represent very limited out-of-plane tissue structure. Here compressive buckling principle is harnessed to create 3D biomimetic cell-laden microstructures from microfabricated planar patterns. This method allows out-of-plane delivery of cells and extracellular matrix patterns with high spatial precision. As a proof of principle, a variety of polymeric 3D miniature structures including a box, an octopus, a pyramid, and continuous waves are fabricated. A mineralized bone tissue model with spatially distributed cell-laden lacunae structures is fabricated to demonstrate the fabrication power of the method. It is expected that this novel approach will help to significantly expand the utility of the established 2D fabrication techniques for 3D tissue fabrication. Given the widespread of 2D fabrication methods in biomedical research and the high demand for biomimetic 3D structures, this method is expected to bridge the gap between 2D and 3D tissue fabrication and open up new possibilities in tissue engineering and regenerative medicine.
| S-EPMC8425919 | biostudies-literature
Project description:Three-dimensional (3D) microstructures created by microfabrication and additive manufacturing have demonstrated value across a number of fields, ranging from biomedicine to microelectronics. However, the techniques used to create these devices each have their own characteristic set of advantages and limitations with regards to resolution, material compatibility, and geometrical constraints that determine the types of microstructures that can be formed. We describe a microfabrication method, termed StampEd Assembly of polymer Layers (SEAL), and create injectable pulsatile drug-delivery microparticles, pH sensors, and 3D microfluidic devices that we could not produce using traditional 3D printing. SEAL allows us to generate microstructures with complex geometry at high resolution, produce fully enclosed internal cavities containing a solid or liquid, and use potentially any thermoplastic material without processing additives.
| S-EPMC6510330 | biostudies-literature
Project description:Various items of roll molds are popularly used to fabricate different kinds of optical films for optoelectronic information and other new and high-tech fields, while the fabrication and evaluation of optical microstructures on a cylindrical roller surface is more difficult than ecumenically manufactured products. In this study, the machinability of microstructures on the roll based on a fast tool servo (FTS) system is investigated. First, the flexible hinge holder for a FTS is designed and its structural parameters are optimized with finite-element analysis and fatigue reliability theory. The tool radius compensation algorithm for complicated microstructures is then deduced based on the surface fitting and bilinear interpolation algorithm of discrete data. Meanwhile, the evaluation index and method are proposed by the medium section method. Finally, a machining test of aspheric arrays on a cylindrical aluminum surface is carried out, and the high quality of the microstructure indicates that the proposed method is able to be used to fabricate optical microstructures.
| S-EPMC7737994 | biostudies-literature
Project description:Observing dynamic micro-scale phenomena occurring at millisecond time scales, such as organism activity, micron particle flows, or any opaque object observation, requires volumetric microscopy techniques able to achieve high data acquisition rates while maintaining contrast so that measurement of fine micro-scale features is possible. In realizing this purpose, the light-field (LF) technique has already been used on three-dimensional (3D) scene capturing and even for microscopic visualizations. In studying the ability and feasibility of 3D surface morphology reconstruction via LF microscopy, we adopted a lab-made LF microscope and integrated a four-dimensional Fourier slice algorithm and a Markov random field propagation algorithm. Furthermore, for numerical comparison and quantized analysis, the Tenengrad function was utilized to calculate the average contrast of the region of interest. Reflective US Air Force targets and 3D photolithography-made micro-scaffolds coated with 50 nm nickel thin films were adopted for system alignment and calibration. The experimental results demonstrate that the developed LF microscope with the signal processing algorithms can observe the 3D surface morphology of opaque microstructures with one snapshot, and has been preliminary applied to Brownian motion observation with 30 Hz volumetric image rate.
| S-EPMC6043499 | biostudies-literature
Project description:Biological mechanisms are often mediated by transient interactions between multiple proteins. The isolation of intact protein complexes is essential to understanding biochemical processes and an important prerequisite for identifying new drug targets and biomarkers. However, low-affinity interactions are often difficult to detect. Here, we use a newly described method called immiscible filtration assisted by surface tension (IFAST) to isolate proteins under defined binding conditions. This method, which gives a near-instantaneous isolation, enables significantly higher recovery of transient complexes compared to current wash-based protocols, which require reequilibration at each of several wash steps, resulting in protein loss. The method moves proteins, or protein complexes, captured on a solid phase through one or more immiscible-phase barriers that efficiently exclude the passage of nonspecific material in a single operation. We use a previously described polyol-responsive monoclonal antibody to investigate the potential of this new method to study protein binding. In addition, difficult-to-isolate complexes involving the biologically and clinically important Wnt signaling pathway were isolated. We anticipate that this simple, rapid method to isolate intact, transient complexes will enable the discoveries of new signaling pathways, biomarkers, and drug targets.
| S-EPMC3897128 | biostudies-literature
Project description:Supercooling of aqueous solutions is a fundamentally and practically important physical phenomenon with numerous applications in biopreservation and beyond. Under normal conditions, heterogeneous nucleation mechanisms critically prohibit the simultaneous long-term (> 1 week), large volume (> 1 ml), and low temperatures (< -10 °C) supercooling of aqueous solutions. Here, we report on the use of surface sealing of water by an oil phase to significantly diminish the primary heterogeneous nucleation at the water/air interface. We achieve deep supercooling (down to -20 °C) of large volumes of water (up to 100 ml) for long periods (up to 100 days) simultaneously via this approach. Since oils are mixtures of various hydrocarbons we also report on the use of pure alkanes and primary alcohols of various lengths to achieve the same. Furthermore, we demonstrate the utility of deep supercooling via preliminary studies on extended (100 days) preservation of human red blood cells.
| S-EPMC6086840 | biostudies-literature
Project description:We developed a method for in situ fabrication of copper nanoparticles inside cotton fibers. Copper nanoparticles can be fabricated mainly in the central part of the fiber by absorbing a raw material solution and by applying microwave heating in a state where the raw material solution is pressed with immiscible liquids. Surface SEM images and cross-sectional EDS mapping for the fabricated fibers clarified that copper nanoparticles fabricated on the cotton surface were suppressed considerably more by the hydrophobic raw material solution than by the hydrophilic raw material solution. These cotton fibers containing copper nanoparticles were found to have antiviral properties against the influenza A virus.
| S-EPMC9042215 | biostudies-literature
Project description:Soft robot fabrication by casting liquid elastomer often requires multiple steps of casting or skillful manual labor. We present a novel soft robotic fabrication technique: negshell casting (negative-space eggshell casting), that reduces the steps required for fabrication by introducing 3D-printed thin-walled cores for use in casting that are meant to be left in place instead of being removed later in the fabrication process. Negshell casting consists of two types of cores: sacrificial cores (negshell cores) and structural cores. Negshell cores are designed to be broken into small pieces that have little effect on the mechanical structure of the soft robot, and can be used for creating fluidic channels and bellows for actuation. Structural cores, on the other hand, are not meant to be broken, and are for increasing the stiffness of soft robotic structures, such as endoskeletons. We describe the design and fabrication concepts for both types of cores and report the mechanical characterization of the cores embedded in silicone rubber specimens. We also present an example use-case of negshell casting for a single joint soft robotic finger, along with an experiment to demonstrate how negshell casting concepts can aid in force transmission. Finally, we present real-world usage of negshell casting in a 6 degree-of-freedom three-finger soft robotic gripper, and a demonstration of the gripper in a robotic pick-and-place task. A companion website with further details about fabrication (as well as an introduction to molding and casting for those who are unfamiliar with the terms), engineering file downloads, and experimental data is provided at https://negshell.github.io/.
| S-EPMC7292399 | biostudies-literature
Project description:Nature has always served as an inspiration for scientists, helping them to solve a large diversity of technical problems. In our case, we are interested in the directional transport of oily liquids and as a model for this application we used the flat bug Dysodius lunatus. In this report, we present arrays of drops looking like polymer microstructures produced by the two-photon polymerization technique that mimic the micro-ornamentation from the bug's cuticle. A good directionality of oil transport was achieved, directly controlled by the direction of the pointed microstructures at the surface. If the tips of the drop-like microstructures are pointing towards the left side, the liquid front moves to the right and vice versa. Similar effects could be expected for the transport of oily lubricants. These results could, therefore, be interesting for applications in friction and wear reduction.
| S-EPMC5383830 | biostudies-literature
Project description:As an indispensable constituent of plasmonic materials/dielectrics for surface enhanced Raman scattering (SERS) effects, dielectrics play a key role in excitation and transmission of surface plasmons which however remain more elusive relative to plasmonic materials. Herein, different roles of vertical dielectric walls, and horizontal and vertical dielectric layers in SERS via 3D periodic plasmonic materials/dielectrics structures are studied. Surface plasmon polariton (SPP) interferences can be maximized within dielectric walls besieged by plasmonic layers at the wall thicknesses of integral multiple half-SPPplasmonic material-dielectric -wavelength which effectively excites localized surface plasmon resonance to improve SERS effects by one order of magnitude compared to roughness and/or nanogaps only. The introduction of extra Au nanoparticles on thin dielectric layers can further enhance SERS effects only slightly. Thus, the designed Au/SiO2 based SERS chips show an enhancement factor of 8.9 × 1010 , 265 times higher relative to the chips with far thinner SiO2 walls. As many as 1200 chips are batch fabricated for a 4 in wafer using cost-effective nanoimprint lithography which can detect trace Hg ions as low as 1 ppt. This study demonstrates a complete generalized platform from design to low-cost batch-fabrication to applications for novel high performance SERS chips of any plasmonic materials/dielectrics.
| S-EPMC9130881 | biostudies-literature