Antigen-responsive, microfluidic valves for single use diagnostics.
Ontology highlight
ABSTRACT:
SUBMITTER: Berron BJ
PROVIDER: S-EPMC4030428 | biostudies-literature | 2012 Feb
REPOSITORIES: biostudies-literature
Publications
Antigen-responsive, microfluidic valves for single use diagnostics.
Berron Brad J BJ May Allison M AM Zheng Zheng Z Balasubramaniam Vivek V Bowman Christopher N CN
Lab on a chip 20120104 4
The growing need for medical diagnostics in resource limited settings is driving the development of simple, standalone immunoassay devices. A capillary flow device using polymerization based amplification is capable of blocking a microfluidic channel in response to target biomaterials, enabling multiple modes of detection that require little or no supplemental instrumentation. ...[more]
Similar Datasets
Project description:This study explores three unique approaches for closing valves and channels within microfluidic systems, specifically multilayer, centrifugally driven polymeric devices. Precise control over the cessation of liquid movement is achieved through either the introduction of expanding polyurethane foam, the application of direct contact heating, or the redeposition of xerographic toner via chloroform solvation and evaporation. Each of these techniques modifies the substrate of the microdevice in a different way. All three are effective at closing a previously open fluidic pathway after a desired unit operation has taken place, i.e., sample metering, chemical reaction, or analytical measurement. Closing previously open valves and channels imparts stringent fluidic control-preventing backflow, maintaining pressurized chambers within the microdevice, and facilitating sample fractionation without cross-contamination. As such, a variety of microfluidic bioanalytical systems would benefit from the integration of these valving approaches.
| S-EPMC7407107 | biostudies-literature
Project description:Pneumatically actuated, non-elastomeric membrane valves fabricated from polymerized polyethylene glycol diacrylate (poly-PEGDA) have been characterized for temporal response, valve closure, and long-term durability. A ~100 ms valve opening time and a ~20 ms closure time offer valve operation as fast as 8 Hz with potential for further improvement. Comparison of circular and rectangular valve geometries indicates that the surface area for membrane interaction in the valve region is important for valve performance. After initial fabrication, the fluid pressure required to open a closed circular valve is ~50 kPa higher than the control pressure holding the valve closed. However, after ~1000 actuations to reconfigure polymer chains and increase elasticity in the membrane, the fluid pressure required to open a valve becomes the same as the control pressure holding the valve closed. After these initial conditioning actuations, poly-PEGDA valves show considerable robustness with no change in effective operation after 115,000 actuations. Such valves constructed from non-adsorptive poly-PEGDA could also find use as pumps, for application in small volume assays interfaced with biosensors or impedance detection, for example.
| S-EPMC3864702 | biostudies-literature
Project description:New microfluidic lab-on-a-chip capabilities are enabled by broadening the toolkit of devices that can be created using microfabrication processes. For example, complex geometries made possible by 3D printing can be used to approach microfluidic design and application in new or enhanced ways. In this paper, we demonstrate three distinct designs for microfluidic one-way (check) valves that can be fabricated using digital light processing stereolithography (DLP-SLA) with a poly(ethylene glycol) diacrylate (PEGDA) resin, each with an internal volume of 5-10 nL. By mapping flow rate to pressure in both the forward and reverse directions, we compare the different designs and their operating characteristics. We also demonstrate pumps for each one-way valve design comprised of two one-way valves with a membrane valve displacement chamber between them. An advantage of such pumps is that they require a single pneumatic input instead of three as for conventional 3D-printed pumps. We also characterize the achievable flow rate as a function of the pneumatic control signal period. We show that such pumps can be used to create a single-stage diffusion mixer with significantly reduced pneumatic drive complexity.
| S-EPMC10384158 | biostudies-literature
Project description:As the outbreak of coronavirus disease 2019 (COVID-19), on-site molecular diagnosis is becoming increasingly important. In this study, a freeze-drying method was introduced for PCR reagents to meet the requirements of microfluidic molecular diagnosis. Using this method, PCR components were pre-mixed and freeze-dried as a bead, which could be transferred into microfluidic chips easily. As this bead only required reconstitution in water, operational steps of PCR were simplified, pipetting errors and errors associated with improper handling of wet reagents could also be reduced. In addition, 19 PCR mixes for different targets (including both RNA and DNA) detection were stable when stored at room temperature (18-25 °C) for 1-2 years and may be stored longer as activity monitoring remains ongoing. To shorten the stability testing time, accelerated stability testing at higher temperatures was proposed. The evaluation periods of the freeze-dried PCR mixes were shortened to less than one month when stored at 56 °C and 80 °C. When attempts were further tried to predict the shelf lives for freeze-dried PCR mixes, our findings challenged the classic view of the Q10 method as a prediction model for freeze-dried PCR mixes and confirmed for the first time that this prediction was influenced by different factors at varying degrees. These studies and findings are important for the development of molecular diagnosis at both central laboratories and resource-limited areas.
| S-EPMC8353973 | biostudies-literature
Project description:In this paper we demonstrate that 3D printing with a digital light processor stereolithographic (DLP-SLA) 3D printer can be used to create high density microfluidic devices with active components such as valves and pumps. Leveraging our previous work on optical formulation of inexpensive resins (RSC Adv., 2015, 5, 106621), we demonstrate valves with only 10% of the volume of our original 3D printed valves (Biomicrofluidics, 2015, 9, 016501), which were already the smallest that have been reported. Moreover, we show that incorporation of a thermal initiator in the resin formulation along with a post-print bake can dramatically improve the durability of 3D printed valves up to 1 million actuations. Using two valves and a valve-like displacement chamber (DC), we also create compact 3D printed pumps. With 5-phase actuation and a 15 ms phase interval, we obtain pump flow rates as high as 40 μL min(-1). We also characterize maximum pump back pressure (i.e., maximum pressure the pump can work against), maximum flow rate (flow rate when there is zero back pressure), and flow rate as a function of the height of the pump outlet. We further demonstrate combining 5 valves and one DC to create a 3-to-2 multiplexer with integrated pump. In addition to serial multiplexing, we also show that the device can operate as a mixer. Importantly, we illustrate the rapid fabrication and test cycles that 3D printing makes possible by implementing a new multiplexer design to improve mixing, and fabricate and test it within one day.
| S-EPMC4917409 | biostudies-literature
Project description:Tissues are composed of highly heterogeneous mixtures of cell subtypes, and this diversity is increasingly being characterized using high-throughput single cell analysis methods. However, these efforts are hindered by the fact that tissues must first be dissociated into single cell suspensions that are viable and still accurately represent phenotypes from the original tissue. Current methods for breaking down tissues are inefficient, labor-intensive, subject to high variability, and potentially biased towards cell subtypes that are easier to release. Here, we present a microfluidic platform consisting of three different tissue processing technologies that can perform the complete tissue to single cell workflow, including digestion, disaggregation, and filtration. First, we developed a new microfluidic digestion device that can be loaded with minced tissue specimens quickly and easily, and then use the combination of proteolytic enzyme activity and fluid shear forces to accelerate tissue breakdown. Next, we integrated dissociation and filter technologies into a single device, which enhanced single cell numbers and fully prepared the sample for single cell analysis. The final multi-device platform was then evaluated using a diverse array of tissue types that exhibited a wide range of properties. For murine kidney and mammary tumor, we found that microfluidic processing produced 2.5-fold more single, viable cells. Single cell RNA sequencing (scRNA-seq) further revealed that device processing enriched for endothelial cells, fibroblasts, and basal epithelium, and did not increase stress responses. For murine liver and heart, which are softer tissues containing fragile cell types, processing time could be reduced to 15 min, and even as short as 1 min. We also demonstrated that periodic recovery at defined time intervals produced substantially more hepatocytes and cardiomyocytes than continuous operation, most likely by preventing damage to fragile cell types. In future work, we will seek to integrate additional operations such as upstream tissue preparation and downstream microfluidic cell sorting and detection to create powerful point-of-care single cell diagnostic platforms.
2021-03-04 | GSE163508 | GEO
Project description:In this paper, a method for fabricating a microfluidic valve made of polydimethylsiloxane (PDMS) using a rapid prototyping method for microchannels through hydrogel cast molding is discussed. Currently, the valves in microchannels play an important role in various microfluidic devices. The technology to prototype microfluidic valves rapidly is actively being developed. For the rapid prototyping of PDMS microchannels, a method that uses a hydrogel as the casting mold has been recently developed. This technique can be used to prepare a three-dimensional structure through simple and uncomplicated methods. In this study, we were able to fabricate microfluidic valves easily using this rapid prototyping method that utilizes hydrogel cast molding. In addition, we confirmed that the valve displacement could be predicted within a range of constant pressures. Moreover, because microfluidic valves fabricated using this method can be directly observed from a cross-sectional direction, we anticipate that this technology will significantly contribute to clarifying fluid behavior and other phenomena in microchannels and microfluidic valves with complex structures.
| S-EPMC4547104 | biostudies-other
Project description:In this study, we developed a method for fabricating a microfluidic device with integrated large-scale all-glass valves and constructed an actuator system to control each of the valves on the device. Such a microfluidic device has advantages that allow its use in various fields, including physical, chemical, and biochemical analyses and syntheses. However, it is inefficient and difficult to integrate the large-scale all-glass valves in a microfluidic device using conventional glass fabrication methods, especially for the through-hole fabrication step. Therefore, we have developed a fabrication method for the large-scale integration of all-glass valves in a microfluidic device that contains 110 individually controllable diaphragm valve units on a 30 mm × 70 mm glass slide. This prototype device was fabricated by first sandwiching a 0.4-mm-thick glass slide that contained 110 1.5-mm-diameter shallow chambers, each with two 50-?m-diameter through-holes, between an ultra-thin glass sheet (4 ?m thick) and another 0.7-mm-thick glass slide that contained etched channels. After the fusion bonding of these three layers, the large-scale microfluidic device was obtained with integrated all-glass valves consisting of 110 individual diaphragm valve units. We demonstrated its use as a pump capable of generating a flow rate of approximately 0.06?5.33 ?L/min. The maximum frequency of flow switching was approximately 12 Hz.
| S-EPMC6190260 | biostudies-literature
Project description:This article presents a magnetically actuated two-way, three-position (+, 0, -), paper-based microfluidic valve that includes a neutral position (0)-the first of its kind. The system is highly robust, customizable, and fully automated. The advent of a neutral position and the ability to precisely control switching frequencies establish a new platform for highly controlled fluid flows in paper-based wicking microfluidic devices. The potential utility of these valves is demonstrated in automated, programmed, patterning of dyed liquids in a wicking device akin to a colorimetric assay but with a programmed fluid/reagent delivery. These valves are fabricated using facile methods and thus remain cost-effective for adoption into affordable point-of-care/bioanalytical devices.
| S-EPMC6641529 | biostudies-literature
Project description:At present, point-of-care (POC) diagnostics typically provide a binary indication of health status (e.g., home pregnancy test strip). Before anticipatory use of diagnostics for assessment of complex diseases becomes widespread, development of sophisticated bioassays capable of quantitatively measuring disease biomarkers is necessary. Successful translation of new bioassays into clinical settings demands the ability to monitor both the onset and progression of disease. Here we report on a clinical POC diagnostic that enables rapid quantitation of an oral disease biomarker in human saliva by using a monolithic disposable cartridge designed to operate in a compact analytical instrument. Our microfluidic method facilitates hands-free saliva analysis by integrating sample pretreatment (filtering, enrichment, mixing) with electrophoretic immunoassays to quickly measure analyte concentrations in minimally pretreated saliva samples. Using 20 microl of saliva, we demonstrate rapid (<10 min) measurement of the collagen-cleaving enzyme matrix metalloproteinase-8 (MMP-8) in saliva from healthy and periodontally diseased subjects. In addition to physiologically measurable indicators of periodontal disease, conventional measurements of salivary MMP-8 were used to validate the microfluidic assays described in this proof-of-principle study. The microchip-based POC diagnostic demonstrated is applicable to rapid, reliable measurement of proteinaceous disease biomarkers in biological fluids.
| S-EPMC1828942 | biostudies-literature