Browse
Submit Data
Databases
API
Help

Dataset Information

15 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Behavior of Tilted Angle Shear Connectors.

ABSTRACT: According to recent researches, angle shear connectors are appropriate to transfer longitudinal shear forces across the steel-concrete interface. Angle steel profile has been used in different positions as L-shaped or C-shaped shear connectors. The application of angle shear connectors in tilted positions is of interest in this study. This study investigates the behaviour of tilted-shaped angle shear connectors under monotonic loading using experimental push out tests. Eight push-out specimens are tested to investigate the effects of different angle parameters on the ultimate load capacity of connectors. Two different tilted angles of 112.5 and 135 degrees between the angle leg and steel beam are considered. In addition, angle sizes and lengths are varied. Two different failure modes were observed consisting of concrete crushing-splitting and connector fracture. By increasing the size of connector, the maximum load increased for most cases. In general, the 135 degrees tilted angle shear connectors have a higher strength and stiffness than the 112.5 degrees type.

SUBMITTER: Khorramian K

PROVIDER: S-EPMC4671601 | biostudies-literature | 2015

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Behavior of Tilted Angle Shear Connectors.

Khorramian Koosha K Maleki Shervin S Shariati Mahdi M Ramli Sulong N H NH

PloS one 20151207 12

According to recent researches, angle shear connectors are appropriate to transfer longitudinal shear forces across the steel-concrete interface. Angle steel profile has been used in different positions as L-shaped or C-shaped shear connectors. The application of angle shear connectors in tilted positions is of interest in this study. This study investigates the behaviour of tilted-shaped angle shear connectors under monotonic loading using experimental push out tests. Eight push-out specimens a ...[more]

PMID: 26642193

Similar Datasets

Shear Capacity of C-Shaped and L-Shaped Angle Shear Connectors.

Project description:This paper investigates the behaviour of C-shaped and L-shaped angle shear connectors embedded in solid concrete slabs. An effective finite element model is proposed to simulate the push out tests of these shear connectors that encompass nonlinear material behaviour, large displacement and damage plasticity. The finite element models are validated against test results. Parametric studies using this nonlinear model are performed to investigate the variations in concrete strength and connector dimensions. The finite element analyses also confirm the test results that increasing the length of shear connector increases their shear strength proportionately. It is observed that the maximum stress in L-shaped angle connectors takes place in the weld attachment to the beam, whereas in the C-shaped angle connectors, it is in the attached leg. The location of maximum concrete compressive damage is rendered in each case. Finally, a new equation for prediction of the shear capacity of C-shaped angle connectors is proposed.

| S-EPMC4968825 | biostudies-literature

Behaviour of Corroded Single Stud Shear Connectors.

Project description:In this study, the effect of corrosion on the static behavior of stud shear connectors was investigated. An innovative test setup for single stud shear connectors was designed and established. Two series of specimens having different stud diameters were fabricated and tested. The test specimens were firstly corroded to different corrosion rates by the electronic accelerating method. Static loading tests were then performed to obtain the load-slip curves and ultimate strengths of the corroded test specimens. The actual corrosion rates were measured from the studs obtained from the tested specimens. The test results were compared with the push out test specimens having similar corrosion rates. It is shown that the test results obtained from the single stud shear connectors are conservative compared with the corroded push test specimens, which prove the validation of the single stud shear connector test method. The effect of corrosion on the behavior of stud shear connectors was also presented.

| S-EPMC5503412 | biostudies-other

Cell separation using tilted-angle standing surface acoustic waves.

Project description:Separation of cells is a critical process for studying cell properties, disease diagnostics, and therapeutics. Cell sorting by acoustic waves offers a means to separate cells on the basis of their size and physical properties in a label-free, contactless, and biocompatible manner. The separation sensitivity and efficiency of currently available acoustic-based approaches, however, are limited, thereby restricting their widespread application in research and health diagnostics. In this work, we introduce a unique configuration of tilted-angle standing surface acoustic waves (taSSAW), which are oriented at an optimally designed inclination to the flow direction in the microfluidic channel. We demonstrate that this design significantly improves the efficiency and sensitivity of acoustic separation techniques. To optimize our device design, we carried out systematic simulations of cell trajectories, matching closely with experimental results. Using numerically optimized design of taSSAW, we successfully separated 2- and 10-µm-diameter polystyrene beads with a separation efficiency of ∼ 99%, and separated 7.3- and 9.9-µm-polystyrene beads with an efficiency of ∼ 97%. We illustrate that taSSAW is capable of effectively separating particles-cells of approximately the same size and density but different compressibility. Finally, we demonstrate the effectiveness of the present technique for biological-biomedical applications by sorting MCF-7 human breast cancer cells from nonmalignant leukocytes, while preserving the integrity of the separated cells. The method introduced here thus offers a unique route for separating circulating tumor cells, and for label-free cell separation with potential applications in biological research, disease diagnostics, and clinical practice.

| S-EPMC4246961 | biostudies-literature

Modeling of Mesoscale Variability in Biofilm Shear Behavior.

Project description:Formation of bacterial colonies as biofilm on the surface/interface of various objects has the potential to impact not only human health and disease but also energy and environmental considerations. Biofilms can be regarded as soft materials, and comprehension of their shear response to external forces is a key element to the fundamental understanding. A mesoscale model has been presented in this article based on digitization of a biofilm microstructure. Its response under externally applied shear load is analyzed. Strain stiffening type behavior is readily observed under high strain loads due to the unfolding of chains within soft polymeric substrate. Sustained shear loading of the biofilm network results in strain localization along the diagonal direction. Rupture of the soft polymeric matrix can potentially reduce the intercellular interaction between the bacterial cells. Evolution of stiffness within the biofilm network under shear reveals two regimes: a) initial increase in stiffness due to strain stiffening of polymer matrix, and b) eventual reduction in stiffness because of tear in polymeric substrate.

| S-EPMC5091762 | biostudies-literature

Interfibrillar shear behavior is altered in aging tendon fascicles.

Project description:Tendon elongation involves both stretching and sliding between adjacent fascicles and fibers. Hence, age-related changes in tendon matrix properties may alter sliding behavior and thereby affect injury thresholds. The objective of this study was to investigate the effects of age on interfibrillar shear behavior in partial cut tendon fascicles. Cine microscopic imaging was used to track deformation patterns of intact and partial cut fascicles from mature (9 months, n = 10) and aged (32 months, n = 10) rat tail tendons. Finite element (FE) models coupled with experimental data provided insight into age-related changes in tissue constitutive properties that could give rise to age-dependent behavior. Intact fascicles from aged tendons exhibited a 28% lower linear region modulus and reduced toe region when compared to fascicles from mature tendons. Partial cut tendon fascicles consistently exhibited a shearing plane that extended longitudinally from the tip of the cut. Both mature and aged fascicles exhibited distinct failure that was observable in differential displacement across the shearing plane. However, aged fascicles exhibited 11-20% higher grip-to-grip strain at failure and tended to exhibit more variable and greater differential displacement at failure, when compared to mature fascicles. FE models suggest that this age-related change in shear behavior arises from a reduction in interfibrillar shear modulus with age. These data suggest that aging alters interfibrillar failure mechanisms and hence may contribute to the increased propensity for injury that is commonly seen in older tendons.

| S-EPMC7210070 | biostudies-literature

Divergent Shear Thinning and Shear Thickening Behavior of Supramolecular Polymer Networks in Semidilute Entangled Polymer Solutions.

Project description:The steady shear behavior of metallo-supramolecular polymer networks formed by bis-Pd(II) cross-linkers and semidilute entangled solutions of poly(4-vinylpyridine) (PVP) in dimethyl sulfoxide (DMSO) or N,N-dimethyl formamide (DMF) is reported. The steady shear behavior of the networks depends on the dissociation rate and association rate of the cross-linkers, the concentration of cross-linkers, and the concentration of the polymer solution. The divergent steady shear behavior-shear thinning versus shear thickening-of samples with identical structure but different cross-linker dynamics (J. Phys. Chem. Lett. 2010, 1, 1683-1686) is further explored in this paper. The divergent steady shear behavior for networks with different cross-linkers is connected to a competition between different time scales: the average time that a cross-linker remains open (?(1)) and the local relaxation time of a segment of polymer chain (?(segment)). When ?(1) is larger than ?(segment), shear thickening is observed. When ?(1) is smaller than ?(segment), only shear thinning is observed.

| S-EPMC3085257 | biostudies-literature

Shear-stabilized rolling behavior of E. coli examined with simulations.

Project description:Escherichia coli exhibit both shear-stabilized rolling and a transition to stationary adhesion while adhering in fluid flow. Understanding the mechanism by which this shear-enhanced adhesion occurs is an important step in understanding bacterial pathogenesis. In this work, simulations are used to investigate the relative contributions of fimbrial deformation and bond transitions to the rolling and stationary adhesion of E. coli. Each E. coli body is surrounded by many long, thin fimbriae terminating in a single FimH receptor that is capable of forming a catch bond with mannose. As simulated cells progress along a mannosylated surface under flow, the fimbriae bend and buckle as they interact with the surface, and FimH-mannose bonds form and break according to a two-state, allosteric catch-bond model. In simulations, shear-stabilized rolling resulted from an increase in the low-affinity bond number due to increased fimbrial deformation with shear. Catch-bond formation did not occur during cell rolling, but instead led to the transition to stationary adhesion. In contrast, in leukocyte and platelet systems, catch bonds appear to be involved in the stabilization of rolling, and integrin activation is required for stationary adhesion.

| S-EPMC2956214 | biostudies-literature

Impact of Reinforcement Ratio on Shear Behavior of I-Shaped UHPC Beams with and without Fiber Shear Reinforcement.

Project description:In the presented paper, the impacts of steel fiber use and tensile reinforcement ratio on shear behavior of Ultra-High Performance Concrete (UHPC) beams were investigated from the point of different tensile reinforcement ratios. In the scope of the experimental program, a total of eight beams consisting of four reinforcement ratios representing low to high ratios ranged from 0.8% to 2.2% were casted without shear reinforcement and subjected to the four-point loading test. While half of the test beams included 30 mm end-hooked steel fibers (SF-UHPC) with 2.0 vol%, the remaining beams were produced without the fiber to show possible effectiveness of the fiber use. The shear performances were discussed in terms of the load-deflection response, cracking pattern and failure mode, first cracking load and ultimate shear strength. In this sense, all the non-fiber beams were failed by shear with a dramatic load drop, regardless of the tensile reinforcement amount, before the yielding of reinforcement and they produced no deflection capability. The test results showed that while the inclusion of steel fibers to the UHPC mixture with low reinforcement ratios changed the failure mode from the shear to flexure, it significantly enhanced the ultimate shear strength in the case of higher reinforcement ratio through the SF-UHPC' superior mechanical properties and fibers' crack-bridging ability.

| S-EPMC7177452 | biostudies-literature

Angle of inclination of tank-treading red cells: dependence on shear rate and suspending medium.

Project description:Red cells suspended in solutions much more viscous than blood plasma assume an almost steady-state orientation when sheared above a threshold value of shear rate. This orientation is a consequence of the motion of the membrane around the red cell called tank-treading. Observed along the undisturbed vorticity of the shear flow, tank-treading red cells appear as slender bodies. Their orientation can be quantified as an angle of inclination (?) of the major axis with respect to the undisturbed flow direction. We measured ? using solution viscosities (?0) and shear rates (??) covering one and three orders of magnitude, respectively. At the lower values of ?0, ? was almost independent of ??. At the higher values of ?0, ? displayed a maximum at intermediate shear rates. The respective maximal values of ? increased by ?10° from 10.7 to 104 mPas. After accounting for the absent membrane viscosity in models by using an increased cytoplasmic viscosity, their predictions of ? agree qualitatively with our data. Comparison of the observed variation of ? at constant ?? with model results suggests a change in the reference configuration of the shear stiffness of the membrane.

| S-EPMC4375532 | biostudies-literature

Creep to inertia dominated stick-slip behavior in sliding friction modulated by tilted non-uniform loading.

Project description:Comprehension of stick-slip motion is very important for understanding tribological principles. The transition from creep-dominated to inertia-dominated stick-slip as the increase of sliding velocity has been described by researchers. However, the associated micro-contact behavior during this transition has not been fully disclosed yet. In this study, we investigated the stick-slip behaviors of two polymethyl methacrylate blocks actively modulated from the creep-dominated to inertia-dominated dynamics through a non-uniform loading along the interface by slightly tilting the angle of the two blocks. Increasing the tilt angle increases the critical transition velocity from creep-dominated to inertia-dominated stick-slip behaviors. Results from finite element simulation disclosed that a positive tilt angle led to a higher normal stress and a higher temperature on blocks at the opposite side of the crack initiating edge, which enhanced the creep of asperities during sliding friction. Acoustic emission (AE) during the stick-slip has also been measured, which is closely related to the different rupture modes regulated by the distribution of the ratio of shear to normal stress along the sliding interface. This study provided a more comprehensive understanding of the effect of tilted non-uniform loading on the local stress ratio, the local temperature, and the stick-slip behaviors.

| S-EPMC5027382 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data