Synthesis of Large-Area WS2 monolayers with Exceptional Photoluminescence.
Ontology highlight
ABSTRACT:
SUBMITTER: McCreary KM
PROVIDER: S-EPMC4725944 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Unlike MoS2 ultra-thin films, where solution-based single source precursor synthesis for electronic applications has been widely studied, growing uniform and large area few-layer WS2 films using this approach has been more challenging. Here, we report a method for growth of few-layer WS2 that results in continuous and uniform films over centimetre scale. The method is based on the thermolysis of spin coated ammonium tetrathiotungstate ((NH4)2WS4) films by two-step high temperature annealing without additional sulphurization. This facile and scalable growth method solves previously encountered film uniformity issues. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) were used to confirm the few-layer nature of WS2 films. Raman and X-Ray photoelectron spectroscopy (XPS) revealed that the synthesized few-layer WS2 films are highly crystalline and stoichiometric. Finally, WS2 films as-deposited on SiO2/Si substrates were used to fabricate a backgated Field Effect Transistor (FET) device for the first time using this precursor to demonstrate the electronic functionality of the material and further validate the method.
| S-EPMC6997350 | biostudies-literature
Project description:Large-area monolayer WS2 is a desirable material for applications in next-generation electronics and optoelectronics. However, the chemical vapour deposition (CVD) with rigid and inert substrates for large-area sample growth suffers from a non-uniform number of layers, small domain size and many defects, and is not compatible with the fabrication process of flexible devices. Here we report the self-limited catalytic surface growth of uniform monolayer WS2 single crystals of millimetre size and large-area films by ambient-pressure CVD on Au. The weak interaction between the WS2 and Au enables the intact transfer of the monolayers to arbitrary substrates using the electrochemical bubbling method without sacrificing Au. The WS2 shows high crystal quality and optical and electrical properties comparable or superior to mechanically exfoliated samples. We also demonstrate the roll-to-roll/bubbling production of large-area flexible films of uniform monolayer, double-layer WS2 and WS2/graphene heterostructures, and batch fabrication of large-area flexible monolayer WS2 film transistor arrays.
| S-EPMC4633959 | biostudies-literature
Project description:High-quality WS2 film with the single domain size up to 400 ?m was grown on Si/SiO2 wafer by atmospheric pressure chemical vapor deposition. The effects of some important fabrication parameters on the controlled growth of WS2 film have been investigated in detail, including the choice of precursors, tube pressure, growing temperature, holding time, the amount of sulfur powder, and gas flow rate. By optimizing the growth conditions at one atmospheric pressure, we obtained tungsten disulfide single domains with an average size over 100 ?m. Raman spectra, atomic force microscopy, and transmission electron microscopy provided direct evidence that the WS2 film had an atomic layer thickness and a single-domain hexagonal structure with a high crystal quality. And the photoluminescence spectra indicated that the tungsten disulfide films showed an evident layer-number-dependent fluorescence efficiency, depending on their energy band structure. Our study provides an important experimental basis for large-area, controllable preparation of atom-thick tungsten disulfide thin film and can also expedite the development of scalable high-performance optoelectronic devices based on WS2 film.
| S-EPMC5626679 | biostudies-literature
Project description:This paper examines the relationship between mechanical deformation and the electronic properties of self-assembled monolayers (SAMs) of the oligothiophene 4-([2,2':5',2?:5?,2?-quaterthiophen]-5-yl)butane-1-thiol (T4C4) in tunneling junctions using conductive probe atomic force microscopy (CP-AFM) and eutectic Ga-In (EGaIn). We compared shifts in conductivity, transition voltages of T4C4 with increasing AFM tip loading force to alkanethiolates. While these shifts result from an increasing tilt angle from penetration of the SAM by the AFM tip for the latter, we ascribe them to distortions of the ? system present in T4C4, which is more mechanically robust than alkanethiolates of comparable length; SAMs comprising T4C4 shows about five times higher Young's modulus than alkanethiolates. Density functional theory calculations confirm that mechanical deformations shift the barrier height due to changes in the frontier orbitals caused by small rearrangements to the conformation of the quaterthiophene moiety. The mechanical robustness of T4C4 manifests as an increased tolerance to high bias in large-area EGaIn junctions suggesting that electrostatic pressure plays a significant role in the shorting of molecular junctions at high bias.
| S-EPMC5512119 | biostudies-literature
Project description:Monolayer MoS2 can be used for various applications such as flexible optoelectronics and electronics due to its exceptional optical and electronic properties. For these applications, large-area synthesis of high-quality monolayer MoS2 is highly desirable. However, the conventional chemical vapor deposition (CVD) method using MoO3 and S powder has shown limitations in synthesizing high-quality monolayer MoS2 over a large area on a substrate. In this study, we present a novel carbon cloth-assisted CVD method for large-area uniform synthesis of high-quality monolayer MoS2. While the conventional CVD method produces thick MoS2 films in the center of the substrate and forms MoS2 monolayers at the edge of the thick MoS2 films, our carbon cloth-assisted CVD method uniformly grows high-quality monolayer MoS2 in the center of the substrate. The as-synthesized monolayer MoS2 was characterized in detail by Raman/photoluminescence spectroscopy, atomic force microscopy, and transmission electron microscopy. We reveal the growth process of monolayer MoS2 initiated from MoS2 seeds by synthesizing monolayer MoS2 with varying reaction times. In addition, we show that the CVD method employing carbon powder also produces uniform monolayer MoS2 without forming thick MoS2 films in the center of the substrate. This confirms that the large-area growth of monolayer MoS2 using the carbon cloth-assisted CVD method is mainly due to reducing properties of the carbon material, rather than the effect of covering the carbon cloth. Furthermore, we demonstrate that our carbon cloth-assisted CVD method is generally applicable to large-area uniform synthesis of other monolayer transition metal dichalcogenides, including monolayer WS2.
| S-EPMC8468553 | biostudies-literature
Project description:In recent years, there have been tremendous advancements in the growth of monolayer transition metal dichalcogenides (TMDCs) by chemical vapor deposition (CVD). However, obtaining high photoluminescence quantum yield (PL QY), which is the key figure of merit for optoelectronics, is still challenging in the grown monolayers. Specifically, the as-grown monolayers often exhibit lower PL QY than their mechanically exfoliated counterparts. In this work, we demonstrate synthetic tungsten diselenide (WSe2) monolayers with PL QY exceeding that of exfoliated crystals by over an order of magnitude. PL QY of ~60% is obtained in monolayer films grown by CVD, which is the highest reported value to date for WSe2 prepared by any technique. The high optoelectronic quality is enabled by the combination of optimizing growth conditions via tuning the halide promoter ratio, and introducing a simple substrate decoupling method via solvent evaporation, which also mechanically relaxes the grown films. The achievement of scalable WSe2 with high PL QY could potentially enable the emergence of technologically relevant devices at the atomically thin limit.
| S-EPMC6314873 | biostudies-literature
Project description:In recent decades, surface air temperature (SAT) data from Global reanalyses points to maximum warming over the northern Barents area. However, a scarcity of observations hampers the confidence of reanalyses in this Arctic hotspot region. Here, we study the warming over the past 20-40 years based on new available SAT observations and a quality controlled comprehensive SAT dataset from the northern archipelagos in the Barents Sea. We identify a statistically significant record-high annual warming of up to 2.7 °C per decade, with a maximum in autumn of up to 4.0 °C per decade. Our results are compared with the most recent global and Arctic regional reanalysis data sets, as well as remote sensing data records of sea ice concentration (SIC), sea surface temperature (SST) and high-resolution ice charts. The warming pattern is primarily consistent with reductions in sea ice cover and confirms the general spatial and temporal patterns represented by reanalyses. However, our findings suggest even a stronger rate of warming and SIC-SAT relation than was known in this region until now.
| S-EPMC9200822 | biostudies-literature
Project description:Two-dimensional transition metal dichalcogenides (2D-TMDs) hold a great potential to platform future flexible optoelectronics. The beating hearts of these materials are their excitons known as XA and XB, which arise from transitions between spin-orbit split (SOS) levels in the conduction and valence bands at the K-point. The functionality of 2D-TMD-based devices is determined by the dynamics of these excitons. One of the most consequential channels of exciton decay on the device functionality is the defect-assisted recombination (DAR). Here, we employ steady-state absorption and emission spectroscopies, and pump density-dependent femtosecond transient absorption spectroscopy to report on the effect of DAR on the lifetime of excitons in monolayers of tungsten disulfide (2D-WS2) and diselenide (2D-WSe2). These pump-probe measurements suggested that while exciton decay dynamics in both monolayers are driven by DAR, in 2D-WS2, defect states near the XB exciton fill up before those near the XA exciton. However, in the 2D-WSe2 monolayer, the defect states fill up similarly. Understanding the contribution of DAR on the lifetime of excitons and the partition of this decay channel between XA and XB excitons may open new horizons for the incorporation of 2D-TMD materials in future optoelectronics.
| S-EPMC8002918 | biostudies-literature
Project description:With downscaling of device dimensions, two-dimensional (2D) semiconducting transition metal dichalcogenides (TMDs) such as WS2 are being considered as promising materials for future applications in nanoelectronics. However, at these nanoscale regimes, incorporating TMD layers in the device architecture with precise control of critical features is challenging using current top-down processing techniques. In this contribution, we pioneer the combination of two key avenues in atomic-scale processing: area-selective atomic layer deposition (AS-ALD) and growth of 2D materials, and demonstrate bottom-up processing of 2D WS2 nanolayers. Area-selective deposition of WS2 nanolayers is enabled using an ABC-type plasma-enhanced ALD process involving acetylacetone (Hacac) as inhibitor (A), bis(tert-butylimido)-bis(dimethylamido)-tungsten as precursor (B), and H2S plasma as the co-reactant (C) at a low deposition temperature of 250 °C. The developed AS-ALD process results in the immediate growth of WS2 on SiO2 while effectively blocking growth on Al2O3 as confirmed by in situ spectroscopic ellipsometry and ex situ X-ray photoelectron spectroscopy measurements. As a proof of concept, the AS-ALD process is demonstrated on patterned Al2O3/SiO2 surfaces. The AS-ALD WS2 films exhibited sharp Raman (E 2g 1 and A 1g) peaks on SiO2, a fingerprint of crystalline WS2 layers, upon annealing at temperatures within the thermal budget of semiconductor back-end-of-line processing (?450 °C). Our AS-ALD process also allows selective growth on various TMDs and transition metal oxides while blocking growth on HfO2 and TiO2. It is expected that this work will lay the foundation for area-selective ALD of other 2D materials.
| S-EPMC7217612 | biostudies-literature
Project description:A model has been developed to account for and prevent the anomalies encountered in topographic images of transition metal dichalcogenide monolayers using dynamic atomic force microscopy (dAFM). The height of WS2 monolayers measured using dAFM appeared to be increased or decreased, resulting from the interactions between the tip and the surface. The hydrophilic SiO2 substrate appeared higher than the weakly hydrophilic WS2 when the tip amplitude was low or at a high set point (high force). Large amplitudes and low set points corrected the step height inversion, but did not recover the true step height. Removing water from the sample resulted in an order of magnitude reduced variation in step height, but the WS2 appeared inverted except at low amplitudes and high set points. Our model explains the varying step heights in dAFM of TMDs as a result of varying tip-sample interactions between the sample and substrate, in the presence or absence of capillaries. To eliminate contrast inversion, high amplitudes can be used to reduce the effect of capillary forces. However, when capillaries are not present, low amplitudes and high set points produce images with proper contrast due to tool operation in the repulsive regime on both materials.
| S-EPMC5736643 | biostudies-literature