Pyrolytic carbon coated black silicon.
Ontology highlight
ABSTRACT:
SUBMITTER: Shah A
PROVIDER: S-EPMC4865946 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Plasmonic optical tweezers are a ubiquitous tool for the precise manipulation of nanoparticles and biomolecules at low photon flux, while femtosecond-laser optical tweezers can probe the nonlinear optical properties of the trapped species with applications in biological diagnostics. In order to adopt plasmonic optical tweezers in real-world applications, it is essential to develop large-scale fabrication processes without compromising the trapping efficiency. Here, we develop a novel platform for continuous wave (CW) and femtosecond plasmonic optical tweezers, based on gold-coated black silicon. In contrast with traditional lithographic methods, the fabrication method relies on simple, single-step, maskless tabletop laser processing of silicon in water that facilitates scalability. Gold-coated black silicon supports repeatable trapping efficiencies comparable to the highest ones reported to date. From a more fundamental aspect, a plasmon-mediated efficiency enhancement is a resonant effect, and therefore, dependent on the wavelength of the trapping beam. Surprisingly, a wavelength characterization of plasmon-enhanced trapping efficiencies has evaded the literature. Here, we exploit the repeatability of the recorded trapping efficiency, offered by the gold-coated black silicon platform, and perform a wavelength-dependent characterization of the trapping process, revealing the resonant character of the trapping efficiency maxima. Gold-coated black silicon is a promising platform for large-scale parallel trapping applications that will broaden the range of optical manipulation in nanoengineering, biology, and the study of collective biophotonic effects.
| S-EPMC4872531 | biostudies-literature
Project description:Combining carbon nanotubes (CNTs), graphene or conducting polymers with conventional silicon wafers leads to promising solar cell architectures with rapidly improved power conversion efficiency until recently. Here, we report CNT-Si junction solar cells with efficiencies reaching 15% by coating a TiO₂ antireflection layer and doping CNTs with oxidative chemicals, under air mass (AM 1.5) illumination at a calibrated intensity of 100 mW/cm² and an active device area of 15 mm². The TiO₂ layer significantly inhibits light reflectance from the Si surface, resulting in much enhanced short-circuit current (by 30%) and external quantum efficiency. Our method is simple, well-controlled, and very effective in boosting the performance of CNT-Si solar cells.
| S-EPMC3504926 | biostudies-literature
Project description:Thermal analysis is essential for the characterization of polymers and drugs. However, the currently established methods require a large amount of sample. Here, we present pyrolytic carbon resonators as promising tools for micromechanical thermal analysis (MTA) of nanograms of polymers. Doubly clamped pre-stressed beams with a resonance frequency of 233 ± 4 kHz and a quality factor (Q factor) of 800 ± 200 were fabricated. Optimization of the electrical conductivity of the pyrolytic carbon allowed us to explore resistive heating for integrated temperature control. MTA was achieved by monitoring the resonance frequency and quality factor of the carbon resonators with and without a deposited sample as a function of temperature. To prove the potential of pyrolytic carbon resonators as thermal analysis tools, the glass transition temperature (T g) of semicrystalline poly(L-lactic acid) (PLLA) and the melting temperature (T m) of poly(caprolactone) (PCL) were determined. The results show that the T g of PLLA and T m of PCL are 61.0 ± 0.8 °C and 60.0 ± 1.0 °C, respectively, which are in excellent agreement with the values measured by differential scanning calorimetry (DSC).
| S-EPMC6803650 | biostudies-literature
Project description:High-theoretical capacity and low working potential make silicon ideal anode for lithium ion batteries. However, the large volume change of silicon upon lithiation/delithiation poses a critical challenge for stable battery operations. Here, we introduce an unprecedented design, which takes advantage of large deformation and ensures the structural stability of the material by developing a two-dimensional silicon nanosheet coated with a thin carbon layer. During electrochemical cycling, this carbon coated silicon nanosheet exhibits unique deformation patterns, featuring accommodation of deformation in the thickness direction upon lithiation, while forming ripples upon delithiation, as demonstrated by in situ transmission electron microscopy observation and chemomechanical simulation. The ripple formation presents a unique mechanism for releasing the cycling induced stress, rendering the electrode much more stable and durable than the uncoated counterparts. This work demonstrates a general principle as how to take the advantage of the large deformation materials for designing high capacity electrode.
| S-EPMC6062545 | biostudies-literature
Project description:The development of better Li-ion battery (LIB) electrodes requires an orchestrated effort to improve the active materials as well as the electron and ion transport in the electrode. In this paper, iron silicide is studied as an anode material for LIBs because of its higher conductivity and lower volume expansion compared to pure Si particles. In addition, carbon nanotubes (CNTs) can be synthesized from the surface of iron-silicides using a continuous flow coating process where precursors are first spray dried into micrometer-scale secondary particles and are then flown through a chemical vapor deposition (CVD) reactor. Some CNTs are formed inside the secondary particles, which are important for short-range electrical transport and good utilization of the active material. Surface-bound CNTs on the secondary particles may help establish a long-range conductivity. We also observed that these spherical secondary particles allow for better electrode coating quality, cyclability, and rate performance than unstructured materials with the same composition. The developed electrodes retain a gravimetric capacity of 1150 mAh/g over 300 cycles at 1A/g as well as a 43% capacity retention at a rate of 5 C. Further, blended electrodes with graphite delivered a 539 mAh/g with high electrode density (?1.6 g/cm3) and areal capacity (?3.5 mAh/cm2) with stable cycling performance.
| S-EPMC6990505 | biostudies-literature
Project description:We propose that bias-modulated graphene-nanocrystallites (GNs) grown vertically can enhance the photoelectric property of carbon film coated on n-Si substrate. In this work, GN-embedded carbon (GNEC) films were deposited by the electron cyclotron resonance (ECR) sputtering technique. Under a reverse diode bias which lifts the Dirac point of GNs to a higher value, the GNEC film/n-Si device achieved a high photocurrent responsivity of 0.35 A/W. The bias-modulated position of the Dirac point resulted in a tunable ON/OFF ratio and a variable spectral response peak. Moreover, due to the standing structured GNs keeping the transport channels, a response time of 2.2 ?s was achieved. This work sheds light on the bias-control wavelength-sensitive photodetector applications.
| S-EPMC6473602 | biostudies-literature
Project description:Black silicon is a synthetic nanomaterial that contains high aspect ratio nanoprotrusions on its surface, produced through a simple reactive-ion etching technique for use in photovoltaic applications. Surfaces with high aspect-ratio nanofeatures are also common in the natural world, for example, the wings of the dragonfly Diplacodes bipunctata. Here we show that the nanoprotrusions on the surfaces of both black silicon and D. bipunctata wings form hierarchical structures through the formation of clusters of adjacent nanoprotrusions. These structures generate a mechanical bactericidal effect, independent of chemical composition. Both surfaces are highly bactericidal against all tested Gram-negative and Gram-positive bacteria, and endospores, and exhibit estimated average killing rates of up to ~450,000 cells min(-1) cm(-2). This represents the first reported physical bactericidal activity of black silicon or indeed for any hydrophilic surface. This biomimetic analogue represents an excellent prospect for the development of a new generation of mechano-responsive, antibacterial nanomaterials.
| S-EPMC3868328 | biostudies-literature
Project description:We report a black silicon-carbon nanotube (bSi-CNT) hybrid structure for ultrahigh absorbance at wide spectral range of wavelength (300-1200?nm). CNTs are densely grown on entire bSi stems by chemical vapor deposition (CVD) through uniformly coating Fe catalyst. The bSi-CNT not only increases the surface roughness for enhancing the light suppression, but also allows the absorption of light in a wide wavelength range over the Si band gap (>1000?nm owing to 1.1?eV) due to the small band gap of CNT (0.6?eV). At short wavelength below Si band gap (<1000?nm), the absorbance of bSi-CNT shows average of 98.1%, while bSi shows 89.4%, which is because of high surface roughness of bSi-CNT that enhancing the light trapping. At long wavelength over Si band gap, the absorbance of bSi-CNT was maintained to 96.3% because of the absorption in CNT, while absorbance of bSi abruptly reduces with increase wavelength. Especially, the absorbance of bSi-CNT was showed 93.5% at 1200?nm, which is about 30~90% higher than previously reported bSi. Simple growth of CNTs on bSi can dramatically enhances the absorbance without using any antireflection coating layer. Thus, this study can be employed for realizing high efficiency photovoltaic, photocatalytic applications.
| S-EPMC7049560 | biostudies-literature
Project description:The thermodynamic stability of onion-like carbon (OLC) nanostructures with respect to highly oriented pyrolytic graphite (HOPG) was determined in the interval 765-1030 K by the electromotive force (emf) measurements of solid electrolyte galvanic cell: (Low) Pt|Cr3C2,CrF2,OLC|CaF2s.c.|Cr3C2,CrF2,HOPG|Pt (High). The free energy change of transformation HOPG = OLC was found positive below 920.6 K crossing the zero value at this temperature. Its trend with temperature was well described by a 3rd degree polynomial. The unexpected too high values of [Formula: see text] jointly to the HR-TEM, STEM and EELS evidences that showed OLC completely embedded in rigid cages made of a Cr3C2/CrF2 matrix, suggested that carbon in the electrodes experienced different internal pressures. This was confirmed by the evaluation under constant volume of [dP/dT by the α/κ ratio for OLC (0.5 MPa K(-1)) and HOPG (8 Pa K(-1)) where α and κ are the isobaric thermal expansion and isothermal compressibility coefficients, respectively. The temperature dependency of the pressure was derived and utilized to calculate the enthalpy and entropy changes as function of temperature and pressure. The highest value of the internal pressure experienced by OLC was calculated to be about 7 GPa at the highest temperature. At 920.6 K, ΔrH and ΔrS values are 95.8 kJ mol(-1) and 104.1 JK(-1) mol(-1), respectively. The surface contributions to the energetic of the system were evaluated and they were found negligible compared with the bulk terms. As a consequence of the high internal pressure, the values of the enthalpy and entropy changes were mainly attributed to the formation of carbon defects in OLC considered as multishell fullerenes. The change of the carbon defect fraction is reported as a function of temperature.
| S-EPMC4143374 | biostudies-literature
Project description:Exposure to hydroquinone (HQ) can cause various health hazards and negative impacts on the environment. Therefore, we developed an efficient electrochemical sensor to detect and quantify HQ based on palladium nanoparticles deposited in a porous silicon-polypyrrole-carbon black nanocomposite (Pd@PSi-PPy-C)-fabricated glassy carbon electrode. The structural and morphological characteristics of the newly fabricated Pd@PSi-PPy-C nanocomposite were investigated utilizing FESEM, TEM, EDS, XPS, XRD, and FTIR spectroscopy. The exceptionally higher sensitivity of 3.0156 μAμM-1 cm-2 and a low limit of detection (LOD) of 0.074 μM were achieved for this innovative electrochemical HQ sensor. Applying this novel modified electrode, we could detect wide-ranging HQ (1-450 μM) in neutral pH media. This newly fabricated HQ sensor showed satisfactory outcomes during the real sample investigations. During the analytical investigation, the Pd@PSi-PPy-C/GCE sensor demonstrated excellent reproducibility, repeatability, and stability. Hence, this work can be an effective method in developing a sensitive electrochemical sensor to detect harmful phenol derivatives for the green environment.
| S-EPMC9953257 | biostudies-literature